similar to: INFOSEC 500 XP usb support

Hi, just try the Unitek Self Protek Mistral 1000ipF with nut and I doesn't work. How can I correctly configure it (if the driver support it). Best regards, In my dmesg: [42953293.620000] usb 1-2: new low speed USB device using uhci_hcd and address 7 [42953293.760000] usb 1-2: no configurations [42953293.760000] usb 1-2: can't read configurations, error -22 [42953293.880000] usb 1-2: new

Hello list, ? ?Cannot make Evolution 850 to be recognized, maybe the problem is "Warning: incomplete endpoint descriptor" in lsusb? Details are as follows. NUT installed by download of debian package. Any ideas/suggestions are highly welcome, thanks in advance! --ValenteM = ? ?= ? ? = ? ? = Ubuntu server 12.04.1 LTS (GNU/Linux 3.2.0-35-generic x86_64) sudo dpkg -i

Hi, I have a powermust with a usb connector. I searched the archive and found this post: http://lists.alioth.debian.org/pipermail/nut-upsdev/2006-April/000816.html Must I abandon hope of controlling this UPS via USB with NUT? Added this line to /etc/udev/rules.d/70-nut-usbups.rules: # OMRON - usbhid-ups SYSFS{idVendor}=="06da", SYSFS{idProduct}=="0003",

Bonjour, Je souheterais utilis? la version qui permet le '-x generic',mais je ne sais pas ou la recuperer car ca devrait solutionner mon probleme (cf mail ci-dessous) DaneZ _____ From: DaneZ [mailto:david.guillotte@danez.no-ip.org] To: arnaud.quette@mgeups.com Sent: Sat, 08 Jul 2006 23:24:06 +0200 Subject: Fw: INFOSEC 500 XP en USB _____ Bonjour Arnaud, Je me

Hi all! FYI, after some research in your list I think that blazer_usb is the best driver for my Soyntec Sekury A600 UPS (which is not in the hardware supported lists). I connected it with my system using USB port (it also has serial RS-232) This is the report I have: battery.voltage: 13.60 battery.voltage.nominal: 12.0 beeper.status: enabled device.type: ups driver.name: blazer_usb

Hi everyone, I have a belkin ups that was bought around 2 months ago. It seems like the driver doesn't like the UPS, although on the website it's listed as supported. This is on a gentoo system with nut 2.2.1 . megatec_usb output: ---------SNIP---------- digamma nut # ./megatec_usb -a belkinm -DDDDDD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues

Hello to all list members, I'm trying to make my UPS work with nut-2.2.2 (using Debian Testing, but compiled from source code) for a week ago, with not success. It's a Unitek Alpha 1000Ps, and I supossed it would work with megatec_usb driver, as other Unitek models. It has an USB interface, and when I plug it into my system I've got this message: chopito:/home/jordi# dmesg | tail

Hi all! I have a ups Ippon smart power pro 2000. And it connects to my FreeBSD 7.2 x86 server throught usb. I'm try to setup it in nut with megatec_usb driver... But it is not recognizes ups. I'm try set productid and vendorid in ups.conf, but this is not help. Nut version 2.4.1 below i'm add output of lsusb, my ups.conf and /usr/local/libexec/nut/megatec_usb -a IPPON -DDD

Hi, Just purchashed this UPS. The megatec_usb driver appears to be communicating with the UPS - however, the ups.status field always states "off" /usr/local/ups/bin/megatec_usb -a plexus -DD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] Andrey Lelikov (c)

Hi, Just purchashed this UPS. The megatec_usb driver appears to be communicating with the UPS - however, the ups.status field always states "off" /usr/local/ups/bin/megatec_usb -a plexus -DD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] Andrey Lelikov (c)

Hello all: I have a Yukai PowerMust 1000 USB and it used to work on another computer using megatec_usb driver. Now, I have it in a new computer, but the driver does not detect it. It is there: # lsusb|grep Cypress Bus 006 Device 007: ID 0665:5161 Cypress Semiconductor USB to Serial Permissions are OK: # ls -l /dev/bus/usb/006/007 crw-rw-r-- 1 root nut 189, 646 ago 8 01:51

# /lib/nut/megatec_usb -a myups Network UPS Tools 2.2.0- - Megatec protocol driver 1.5.4 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] No supported devices found. Please check your device availability with 'lsusb' and make sure you have an up-to-date version of NUT. If this does not help, try running the driver with

Hi, I'm new in the list and I'm having a little bit trouble to put the megatec_usb to work. I've been using NUT for a while with the apc and megatec driver (serial), with no problem. The server is a Ubuntu 8.04.2 with NUT version 2.2.1-2.1ubuntu7.2, the default package version in this ubuntu release. I've configured the ups.conf as follows: [sms] driver = megatec_usb

Hi, I'm new in the list and I'm having a little bit trouble to put the megatec_usb to work. I've been using NUT for a while with the apc and megatec driver (serial), with no problem. The server is a Ubuntu 8.04.2 with NUT version 2.2.1-2.1ubuntu7.2, the default package version in this ubuntu release. I've configured the ups.conf as follows: [sms] driver = megatec_usb

G'day, New toy, came with bundled software which is non-free, so I'm looking at whether NUT can be convinced to play with the toy. I've never used NUT before. OS name and version: Ubuntu 10.10 exact NUT version: 2.4.3-1ubuntu5 NUT installation method: Ubuntu package nut exact device name and related information: PowerShield Centurion 2000

hi, i've bought a 750VA orvaldi ups http://en.orvaldi.com/index.php/en/product_catalog/product_view/11/162 which holds my hardware (wifi router, cable modem, quad-core with raid and lcd monitor) for ~15 minutes. pretty nice result for a cheap (~57 euro) home ups. in fact, the vendor software for linux is very old (e.g. requires ancient redhat with qt2), requires db9 port while shipped

I recently bought 2 different USB flash disks. These are some cheap no-name devices. Their parameters: bytes C/H/S ID 4194304512 509/255/63 Vendor: Generic Model: USB Flash Drive Rev: 1.00 ANSI SCSI revision: 02 4288676352 1023/132/62 Vendor: USB Model: USB 2.0 Rev: 1.00 ANSI SCSI revision: 02 When I put a FAT32 filesystem on them,

I have an UPS, that claims to be IPPon Back Power Pro 700. I'm trying to connect it using USB. lsusb -v says: Bus 1 Device 3: ID 06da:0003 Phoenixtec Power Co., Ltd Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0

Greetings Gentlemen, I have Mustek NetGuard 1000 UPS which is equivalent to Ippon SmartWinner 1000. I have tried to run several latest builds of NUT, but run megatec_usb driver still failed with my device. I hope the information below might help. Regards, Oleg Here is the information which may help: lsusb -v Bus 002 Device 002: ID 06da:0003 Phoenixtec Power Co., Ltd Device Descriptor:

Ok guys I get this errors: Network UPS Tools ? UPS driver controller 2.4.1 Network UPS Tools ? Generic HID driver 0.34 (2.4.1) USB communication driver 0.31 No matching HID UPS found my ups.conf is: [ap1000] driver = usbhid-ups port = auto I?ve also tried to set a specific usb port and change driver. My ups is a AMACROX 1000 http://www.amacrox.com//english/01_product/02_01detail.aspx?pdid=46