thr3ads.net - Ext3 users - 4 GB USB flash disk with FAT ok, with ext3 corrupted files [Jun 2007]

If this information is useful, please help other people find it:
Share via:

Miernik

2007-Jun-16 00:56 UTC

4 GB USB flash disk with FAT ok, with ext3 corrupted files

I recently bought 2 different USB flash disks. These are some cheap no-name
devices.  Their parameters:

   bytes            C/H/S       ID
4194304512       509/255/63     Vendor: Generic Model: USB Flash Drive  Rev:
1.00  ANSI SCSI revision: 02
4288676352      1023/132/62     Vendor: USB     Model: USB 2.0          Rev:
1.00  ANSI SCSI revision: 02

When I put a FAT32 filesystem on them, everything is OK, but when I put an ext3
filesystem, everything is OK when I write files to the disk, I can fill it with
files, but then when I remove the disk from the computer (after a proper
umount) and putting it in again, most of the files have corrupted direcotry
entries (they look red in midnight commander, some of them pink). But some
(about 5 to 10%) files are normal, and normally accessible.

I tried them both on two completely different computers with very different
hardware, and different Linux versions, and the effect is the same.

One of the computers is a desktop with and old AMD K7 Clayton motherboard with
only old USB1.1: VT82xxxxx UHCI USB 1.1 Controller, and Debian sid with
2.6.18-4-k7 kernel from Debian.

The other computer is a much newer AMD Athlon64 HP laptop with USB2.0 port and
SuSE 10.2.

Did anyone observe anything similar with any USB flash drives (FAT OK, ext3
corrupted)?

I've put files on these disks on FAT32 and run fsck.vfat, and everything
looks
fine:

root at tarnica:~# dosfsck -v /dev/sda1
dosfsck 2.11 (12 Mar 2005)
dosfsck 2.11, 12 Mar 2005, FAT32, LFN
Checking we can access the last sector of the filesystem
Boot sector contents:
System ID "mkdosfs"
Media byte 0xf8 (hard disk)
       512 bytes per logical sector
      4096 bytes per cluster
        32 reserved sectors
First FAT starts at byte 16384 (sector 32)
         2 FATs, 32 bit entries
   4177920 bytes per FAT (= 8160 sectors)
Root directory start at cluster 2 (arbitrary size)
Data area starts at byte 8372224 (sector 16352)
   1044477 data clusters (4278177792 bytes)
62 sectors/track, 132 heads
         0 hidden sectors
   8372170 sectors total
Checking for unused clusters.
Checking free cluster summary.
/dev/sda1: 121 files, 116397/1044477 clusters
root at tarnica:~# echo "$?"
0
root at tarnica:~#

With FAT I can read any file I saved to the disk just fine, it
simply works.

Maybe you'd like my 'lsusb -v' (this is on the USB1.1-only Debian
machine):


Bus 002 Device 001: ID 0000:0000  
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed hub
  bMaxPacketSize0        64
  idVendor           0x0000 
  idProduct          0x0000 
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.18-4-k7 uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:07.3
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed hub
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood        1 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0300 lowspeed power
   Port 2: 0000.0300 lowspeed power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Bus 001 Device 002: ID 1043:8012 iCreate Technologies Corp. 
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  idVendor           0x1043 iCreate Technologies Corp.
  idProduct          0x8012 
  bcdDevice            1.00
  iManufacturer           1 USB
  iProduct                2 USB 2.0
  iSerial                 0 
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           32
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0x80
      (Bus Powered)
    MaxPower              100mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           2
      bInterfaceClass         8 Mass Storage
      bInterfaceSubClass      6 SCSI
      bInterfaceProtocol     80 Bulk (Zip)
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x02  EP 2 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0
Device Qualifier (for other device speed):
  bLength                10
  bDescriptorType         6
  bcdUSB               2.00
  bDeviceClass            0 (Defined at Interface level)
  bDeviceSubClass         0 
  bDeviceProtocol         0 
  bMaxPacketSize0        64
  bNumConfigurations      1
Device Status:     0x0000
  (Bus Powered)

Bus 001 Device 001: ID 0000:0000  
Device Descriptor:
  bLength                18
  bDescriptorType         1
  bcdUSB               1.10
  bDeviceClass            9 Hub
  bDeviceSubClass         0 Unused
  bDeviceProtocol         0 Full speed hub
  bMaxPacketSize0        64
  idVendor           0x0000 
  idProduct          0x0000 
  bcdDevice            2.06
  iManufacturer           3 Linux 2.6.18-4-k7 uhci_hcd
  iProduct                2 UHCI Host Controller
  iSerial                 1 0000:00:07.2
  bNumConfigurations      1
  Configuration Descriptor:
    bLength                 9
    bDescriptorType         2
    wTotalLength           25
    bNumInterfaces          1
    bConfigurationValue     1
    iConfiguration          0 
    bmAttributes         0xe0
      Self Powered
      Remote Wakeup
    MaxPower                0mA
    Interface Descriptor:
      bLength                 9
      bDescriptorType         4
      bInterfaceNumber        0
      bAlternateSetting       0
      bNumEndpoints           1
      bInterfaceClass         9 Hub
      bInterfaceSubClass      0 Unused
      bInterfaceProtocol      0 Full speed hub
      iInterface              0 
      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x81  EP 1 IN
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0002  1x 2 bytes
        bInterval             255
Hub Descriptor:
  bLength               9
  bDescriptorType      41
  nNbrPorts             2
  wHubCharacteristic 0x000a
    No power switching (usb 1.0)
    Per-port overcurrent protection
  bPwrOn2PwrGood        1 * 2 milli seconds
  bHubContrCurrent      0 milli Ampere
  DeviceRemovable    0x00
  PortPwrCtrlMask    0xff
 Hub Port Status:
   Port 1: 0000.0103 power enable connect
   Port 2: 0000.0100 power
Device Status:     0x0003
  Self Powered
  Remote Wakeup Enabled

Let me give you some more diag.
Here is what I did:

Having read that too large max_sectors sometimes gives problems, I did:

root at tarnica:~# echo "64" > /sys/block/sda/device/max_sectors

But before I tried without reducing max_sectors from the default - no
difference.

root at tarnica:~# mkfs.ext3 /dev/sda1
mke2fs 1.40-WIP (07-Apr-2007)
Filesystem labelOS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
523264 inodes, 1046521 blocks
52326 blocks (5.00%) reserved for the super user
First data block=0
Maximum filesystem blocks=1073741824
32 block groups
32768 blocks per group, 32768 fragments per group
16352 inodes per group
Superblock backups stored on blocks:
        32768, 98304, 163840, 229376, 294912, 819200, 884736

Writing inode tables: done
Creating journal (16384 blocks): done
Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 24 mounts or
180 days, whichever comes first.  Use tune2fs -c or -i to override.
root at tarnica:~# mount /dev/sda1 /mnt/sda1

No errors up till here.

root at tarnica:~# cp -dr /usr/share/doc/ /mnt/sda1/

Here we get this error in kern.log:

Jun 16 00:47:09 tarnica kernel: scsi0: PCI error Interrupt at seqaddr = 0x8
Jun 16 00:47:09 tarnica kernel: scsi0: Data Parity Error Detected during address
or write data phase

root at tarnica:~# sync

Later I did an 'find -ls' in the /mnt/sda1/ directory,
then 'umount /mnt/sda1' and then 'mount /dev/sda1 /mnt/sda1'
again.


The above commands caused that to appear in the output of 'dmesg':

EXT3-fs error (device sda1): ext3_readdir: bad entry in directory #11: rec_len
is smaller than minimal - offset=0, inode=0, rec_len=0, name_len=0
Aborting journal on device sda1.
EXT3-fs error (device sda1) in ext3_ordered_writepage: IO failure
ext3_abort called.
EXT3-fs error (device sda1): ext3_journal_start_sb: Detected aborted journal
Remounting filesystem read-only
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
EXT3-fs error (device sda1): ext3_readdir: bad entry in directory #11: rec_len
is smaller than minimal - offset=0, inode=0, rec_len=0, name_len=0
EXT3-fs error (device sda1): ext3_readdir: bad entry in directory #11: rec_len
is smaller than minimal - offset=0, inode=0, rec_len=0, name_len=0
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_committed_data
__journal_remove_journal_head: freeing b_frozen_data
__journal_remove_journal_head: freeing b_committed_data
kjournald starting.  Commit interval 5 seconds
EXT3-fs warning (device sda1): ext3_clear_journal_err: Filesystem error recorded
from previous mount: IO failure
EXT3-fs warning (device sda1): ext3_clear_journal_err: Marking fs in need of
filesystem check.
EXT3-fs warning: mounting fs with errors, running e2fsck is recommended
EXT3 FS on sda1, internal journal
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.

At this point:

root at tarnica:~# ls -al /mnt/sda1
total 24
drwxr-xr-x  4 root root  4096 2007-06-16 00:47 .
drwxr-xr-x 27 root root  4096 2007-06-09 09:25 ..
drwx------  2 root root 16384 2007-06-16 00:37 lost+found
?---------  ? ?    ?        ?                ? /mnt/sda1/doc
root at tarnica:~#

So I did 'umount /mnt/sda1' and 'e2fsck -v -y /dev/sda1', which
runs endlessly
with a zillion errors, for example:

Inode 133561 has compression flag set on filesystem without compression support.
Clear? yes

Inode 133561 has illegal block(s).  Clear? yes

Illegal block #0 (189057594) in inode 133561.  CLEARED.
Illegal block #1 (3559149010) in inode 133561.  CLEARED.
Illegal block #2 (4279737499) in inode 133561.  CLEARED.
Illegal block #3 (362979125) in inode 133561.  CLEARED.
Illegal block #4 (3152073428) in inode 133561.  CLEARED.
Illegal block #5 (679595262) in inode 133561.  CLEARED.
Illegal block #6 (1924390837) in inode 133561.  CLEARED.
Illegal block #7 (1058295063) in inode 133561.  CLEARED.
Illegal block #8 (795243680) in inode 133561.  CLEARED.
Illegal block #9 (3130620932) in inode 133561.  CLEARED.
Illegal block #10 (1544529913) in inode 133561.  CLEARED.
Too many illegal blocks in inode 133561.
Clear inode? yes


or:


Inode 134287 has compression flag set on filesystem without compression support.
Clear? yes

Inode 134287, i_size is 7400753060221116605, should be 0.  Fix? yes

Inode 134287, i_blocks is 2017258698, should be 0.  Fix? yes

Inode 134303 has compression flag set on filesystem without compression support.
Clear? yes

Inode 134303, i_size is 7400753060221116605, should be 0.  Fix? yes

Inode 134303, i_blocks is 2017258698, should be 0.  Fix? yes


or:


Inode 132391 has imagic flag set.  Clear? yes

Special (device/socket/fifo) inode 132391 has non-zero size.  Fix? yes

Inode 132392 is in use, but has dtime set.  Fix? yes

Inode 132392 has imagic flag set.  Clear? yes


and other different types of errors alternatively, from time to time
doing:

Restarting e2fsck from the beginning...
/dev/sda1 contains a file system with errors, check forced.
Pass 1: Checking inodes, blocks, and sizes


and it seems this goes on forever. Nothing shows in 'dmesg', nor
kern.log nor 'cat /proc/kmsg' nor any other log file/output during doing
the filesystem check.


I would think it's a broken hardware, but this happens on two different
4 GB USB sticks, from two different sources, one used, one new, on
different computers, so it's quite unlikely that both of these sticks
would be bad. Besides that they work perfectly with FAT32. And it is
also unlikely that so different USB controllers on two different
computers would be bad at the same time.

Similar symptoms are in this bug report:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=404486

But I have never saw such symptoms using HDDs, CF cards (also 4 GB ones, on the
same machine) and 256 MB USB flash disks.

Any clues?


-- 
Miernik
http://miernik.name/

Miernik

2007-Jun-16 16:11 UTC

head link

4 GB USB flash disk with FAT ok, with ext3 corrupted files

Posting now to two lists, one about USB and the other about ext3 as I
don't know what is the source of the problem.

Miernik <public at miernik.name> wrote:> I recently bought 2 different USB flash disks. These are some cheap no-name
> devices.  Their parameters:
> 
>   bytes            C/H/S       ID
> 4288676352      1023/132/62     Vendor: USB     Model: USB 2.0         
Rev: 1.00  ANSI SCSI revision: 02
Right now after trying to copy about 0.5 GB of files to a freshly created ext3
filesystem on the device, this is the output of dmesg:

ontroller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Freeing unused kernel memory: 212k freed
input: AT Translated Set 2 keyboard as /class/input/input0
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 2 throttling states)
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 11 (level, low)
-> IRQ 11
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 11, io base 0x0000d400
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ACPI: PCI Interrupt 0000:00:07.3[D] -> Link [LNKD] -> GSI 11 (level, low)
-> IRQ 11
uhci_hcd 0000:00:07.3: UHCI Host Controller
uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:07.3: irq 11, io base 0x0000d800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
8139cp: 10/100 PCI Ethernet driver v1.3 (Mar 22, 2004)
SCSI subsystem initialized
VP_IDE: IDE controller at PCI slot 0000:00:07.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci0000:00:07.1
    ide0: BM-DMA at 0xd000-0xd007, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xd008-0xd00f, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
Time: acpi_pm clocksource has been installed.
hda: ST33210A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
8139cp 0000:00:08.0: This (id 10ec:8139 rev 10) is not an 8139C+ compatible chip
8139cp 0000:00:08.0: Try the "8139too" driver instead.
ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [LNKD] -> GSI 11 (level, low)
-> IRQ 11
libata version 2.20 loaded.
8139too Fast Ethernet driver 0.9.28
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 7.0
        <Adaptec 2940 SCSI adapter>
        aic7870: Single Channel A, SCSI Id=7, 16/253 SCBs

ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [LNKA] -> GSI 10 (level, low)
-> IRQ 10
eth0: RealTek RTL8139 at 0xe800, 00:02:44:29:57:bf, IRQ 10
eth0:  Identified 8139 chip type 'RTL-8139C'
hda: max request size: 128KiB
hda: 6346368 sectors (3249 MB) w/256KiB Cache, CHS=6296/16/63, UDMA(33)
hda: cache flushes not supported
 hda: hda1 hda2 < hda5 >
scsi 0:0:2:0: Processor         HP       C5110A           3638 PQ: 0 ANSI: 2
 target0:0:2: Beginning Domain Validation
 target0:0:2: Ending Domain Validation
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
scsi 0:0:2:0: Attached scsi generic sg0 type 3
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
input: PC Speaker as /class/input/input1
Real Time Clock Driver v1.12ac
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
agpgart: AGP aperture is 64M @ 0xe0000000
parport_pc: VIA 686A/8231 detected
parport_pc: probing current configuration
parport_pc: Current parallel port base: 0x378
parport0: PC-style at 0x378, irq 7 [PCSPP,EPP]
parport_pc: VIA parallel port: io=0x378, irq=7
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 12
PCI: setting IRQ 12 as level-triggered
ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKC] -> GSI 12 (level, low)
-> IRQ 12
PCI: Setting latency timer of device 0000:00:07.5 to 64
EXT3 FS on hda1, internal journal
Probing IDE interface ide1...
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel at
redhat.com
Sound Blaster 16 soundcard not found or device busy
In case, if you have non-AWE card, try snd-sb16 module
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 10 (level, low)
-> IRQ 10
[drm] Initialized radeon 1.25.0 20060524 on minor 0
radeonfb: Found Intel x86 BIOS ROM Image
radeonfb: Retrieved PLL infos from BIOS
radeonfb: Reference=27.00 MHz (RefDiv=12) Memory=240.00 Mhz, System=166.00 MHz
radeonfb: PLL min 20000 max 40000
i2c_adapter i2c-2: unable to read EDID block.
i2c_adapter i2c-2: unable to read EDID block.
i2c_adapter i2c-2: unable to read EDID block.
i2c_adapter i2c-4: unable to read EDID block.
i2c_adapter i2c-4: unable to read EDID block.
i2c_adapter i2c-4: unable to read EDID block.
radeonfb: Monitor 1 type CRT found
radeonfb: EDID probed
radeonfb: Monitor 2 type no found
Console: switching to colour frame buffer device 200x75
radeonfb (0000:01:00.0): ATI Radeon Y` 
Intel ISA PCIC probe: 
  Intel i82365sl B step ISA-to-PCMCIA at port 0x3e0 ofs 0x00, 2 sockets
    host opts [0]: none
    host opts [1]: none
    ISA irqs (scanned) = 9,15 polling interval = 1000 ms
pccard: PCMCIA card inserted into slot 0
TCP hybla registered
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
cs: memory probe 0x0d0000-0x0dffff: excluding 0xd0000-0xd7fff
cs: memory probe 0x0e0000-0x0effff: clean.
pcmcia: registering new device pcmcia0.0
cs: IO port probe 0x100-0x3af: clean.
cs: IO port probe 0x3e0-0x4ff: excluding 0x4d0-0x4d7
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
Probing IDE interface ide2...
hde: SAMSUNG CF/ATA, CFA DISK drive
ide2 at 0x100-0x107,0x10e on irq 9
hde: max request size: 128KiB
hde: 8211168 sectors (4204 MB) w/0KiB Cache, CHS=8146/16/63
 hde: hde1 hde2
ide-cs: hde: Vpp = 0.0
pcmcia: Detected deprecated PCMCIA ioctl usage from process: discover.
pcmcia: This interface will soon be removed from the kernel; please expect
breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for
details.
eth0: link up, 100Mbps, half-duplex, lpa 0x44E1
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
eth0: no IPv6 routers present
input: Power Button (FF) as /class/input/input2
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /class/input/input3
ACPI: Power Button (CM) [PWRB]
input: Sleep Button (CM) as /class/input/input4
ACPI: Sleep Button (CM) [SLPB]
irda_init()
NET: Registered protocol family 23
powernow-k8: Processor cpuid 680 not supported
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Setting GART location based on new memory map
[drm] Loading R200 Microcode
[drm] writeback test succeeded in 1 usecs
kjournald starting.  Commit interval 5 seconds
EXT3 FS on dm-0, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Loading R200 Microcode
usb 1-1: new full speed USB device using uhci_hcd and address 2
usb 1-1: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi1 : SCSI emulation for USB Mass Storage devices
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 1:0:0:0: Direct-Access     USB      USB 2.0          1.00 PQ: 0 ANSI: 2
SCSI device sda: 8376321 512-byte hdwr sectors (4289 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
SCSI device sda: 8376321 512-byte hdwr sectors (4289 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
sda: assuming drive cache: write through
 sda: sda1
sd 1:0:0:0: Attached scsi removable disk sda
sd 1:0:0:0: Attached scsi generic sg1 type 0
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
scsi0: PCI error Interrupt at seqaddr = 0x7
scsi0: Data Parity Error Detected during address or write data phase
usb 1-2: new full speed USB device using uhci_hcd and address 3
usb 1-2: configuration #1 chosen from 1 choice
scsi2 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 3
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 2:0:0:0: Direct-Access     USB 2.0  Mobile Disk      PMAP PQ: 0 ANSI: 0 CCS
SCSI device sdb: 1003520 512-byte hdwr sectors (514 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
SCSI device sdb: 1003520 512-byte hdwr sectors (514 MB)
sdb: Write Protect is off
sdb: Mode Sense: 23 00 00 00
sdb: assuming drive cache: write through
 sdb: sdb1
sd 2:0:0:0: Attached scsi removable disk sdb
sd 2:0:0:0: Attached scsi generic sg2 type 0
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
EXT3 FS on sda1, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
EXT3-fs error (device sda1): ext3_new_block: block(1046522) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046523) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046524) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046525) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046526) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046531) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046532) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046535) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046537) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046541) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046542) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046544) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046546) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046548) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046549) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046550) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046553) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046554) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046556) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046558) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046561) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046562) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046563) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046565) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046566) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046567) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046568) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046571) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046573) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046575) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046578) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046579) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046581) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046582) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046583) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046585) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046586) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046587) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046589) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046590) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046593) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046594) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046595) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046596) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046597) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046598) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046602) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046603) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046604) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046607) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046610) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046612) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046613) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046614) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046615) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046616) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046620) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046622) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046623) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046624) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046625) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046626) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046627) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046628) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046629) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046633) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046636) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046638) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046639) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046641) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046642) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046643) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046646) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046647) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046648) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046650) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046651) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046652) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046653) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046655) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046657) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046661) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046667) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046669) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046671) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046672) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046673) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046674) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046676) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046680) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046681) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046683) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046685) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046686) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046688) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046689) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046690) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046692) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046694) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046697) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046698) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046701) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046705) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046708) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046713) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046714) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046716) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046718) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046721) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046723) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046726) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046727) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046730) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046731) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046732) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046733) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046735) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046736) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046738) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046740) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046741) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046743) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046749) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046751) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046752) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046757) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046758) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046759) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046760) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046762) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046764) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046766) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046767) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046768) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046770) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046772) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046774) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046776) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046777) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046783) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046784) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046786) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046787) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046788) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046790) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046791) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046792) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046795) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046796) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046797) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046799) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046800) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046804) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046806) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046811) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046812) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046813) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046815) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046816) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046817) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046818) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046821) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046822) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046823) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046825) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046826) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046827) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046828) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046830) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046831) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046832) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046834) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046836) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046838) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046839) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046840) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046841) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046843) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046844) >= blocks
count(1046521) - block_group = 31, es == d8f5d400
EXT3-fs error (device sda1): ext3_new_block: block(1046845) >= blocks
count(1046521) - block_group = 31, es == d8f5d400


And trying to write any more files gives "No space left on device"
message,
while only 8% of the device is used:

Filesystem           1K-blocks      Used Available Use% Mounted on
/dev/sda1              4120356    305988   3605064   8% /mnt/sda1

Its mounted like this:

miernik at tarnica:~$ cat /proc/mounts | grep sda1
/dev/sda1 /mnt/sda1 ext3 rw,nosuid,nodev,noexec,data=ordered 0 0
miernik at tarnica:~$

-- 
Miernik
http://miernik.name/

Apparently Analagous Threads

Search for more apparently analagous threads

Ext3 users - Jun 2007 - 4 GB USB flash disk with FAT ok, with ext3 corrupted files

4 GB USB flash disk with FAT ok, with ext3 corrupted files

4 GB USB flash disk with FAT ok, with ext3 corrupted files

Apparently Analagous Threads