similar to: Krauler UP-D1200VA

Hi, This is my first post ever on a technical forum, so please forgive any poor etiquette etc. Also I'm totally new to Linux all of my experience has been trying to get this UPS to work. So please bear this in mind. I'm running OpenSuse 13.1 and I have a Lupus 500 USB (Fideltronik) After quite a bit of playing around I managed to get the status of the UPS using the blazer_usb driver and

On Jun 9, 2014, at 6:40 AM, Hill wrote: > Hi, > This is my first post ever on a technical forum, so please forgive any poor etiquette etc. > Also I'm totally new to Linux all of my experience has been trying to get this UPS to work. So please bear this in mind. No worries. On the NUT lists, we don't set or alter the reply-to header, so please use "reply all" to make

Sorry for the huge delay and thanks Charles for taking care of this topic. >> I'm running OpenSuse 13.1 and I have a Lupus 500 USB (Fideltronik) >> >> After quite a bit of playing around I managed to get the status of the UPS using the blazer_usb driver and running NUT 2.6.5. >> But unfortunately none of the Instcmds such as load.off etc. worked. > > Can you post

On Feb 11, 2008 5:30 PM, Marcio Gomes <mpg at microlink.com.br> wrote: > I change the if in [OFF] detect state to, in original way, if you send a > reset.watchdog, the UPS goes > to OFF state in clients, but it is not correct, because UPS is OL and > Shutdown are in progress, but > the power is not OFF First of all, thanks for the patch. But I have a few comments: Are you

I've got a big UPS from an italian manufacturer MSC elettronica which should be megatec protocol based. They distribute it with Upsilon2000, developed by Megatec, and with a cable listed on the megatec site: http://www.megatec.com.tw/FAQ.htm How do I know the M2505 cable is the one that should be used on my UPS instead of M2502 cable? UPS that use both these cables are TRUE RS232 UPS

Hi, All! I've recently bought an UPS. It is Krauler UP-M500VA, it has USB port and is a HID device. But as I discovered the only HID application it supports is 0x860004, so it isn't claimed by both hidups and newhidups drivers, because it uses a vendor-specific values. I tried to discover values in that x86 page, but I failed. How can I do it? And after I get values how to understand

Hi Stefanos, you should mail to the NUT list, and try the megatec driver, which is only available from subversion for the moment (but should be included in the next stable release). Carlos might give you some help with this driver. Arnaud Quette -- Linux / Unix Expert - MGE UPS SYSTEMS - R&D Dpt Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer -

Hello Peter! Peter Selinger wrote: > This is useful information. I don't think the device is currently > supported, but the information printed above is enough to write a > subdriver for it. Note that the purpose of the "-x generic" option is > precisely to produce this output. [...] >> Apparently the UPS is recognized but no communication is >>

Sorry for my delay, I've only just read this mail. At first glance the driver looks like it should work, I will test it tomorrow (if possible) and let you know. I'll also give a reply to your questions. Many thanks for the work you've already put into this. -------------------------------------------------- From: <hyouko at gmail.com> Sent: Monday, June 30, 2014 12:42 AM To:

Hello Charles! As promised, I just checked out the CVS and recompiled everything. In the attached .txt is what is coming out from my UPS. I am wondering about all those zeroes. Also, this morning I plan to connect the UPS to a Win box running the monitoring program supplied with the UPS (UPSilon2000) and a USB sniffer program. If you have any suggestions on what to look for in the data,

Hi Arnaud and NUT team You may recall some time ago, I and a few others posted questions about the above referenced (cheap and cheerful) USB-based UPS - specifically regarding FreeBSD USB support in NUT. The original posting was entitled "Zigor Ebro 650 compatibility". I've since tried the latest Windows port of NUT with my WinXP laptop connected to the Zigor Ebro and finally

Hi to all and happy new year! I'm writing here as I'm trying to get nut supporting the UPS in the subject; I didn't check well before buying and nowI discovered this is kinda bad hardware (it doesn't have a valid USB id, it just reports 0000:0001 and linux support doesn't really work as they stated), but before changing it I wanted to try to find a solution to get it work with

Merry Christmas to you all and best wishes! I ran into exactly the same problem as described. OS: FreeBSD 9.0-Rel UPS: Eaton E-Series NV 600H NUT: from Ports, nut-2.6.5_1 driver: blazer_usb I am sure the problem is not permission-related as it occurs even when the driver runs as root. My tested recipe for USB permissions is: 1. run usbconfig to find where the device is connected. In my case:

Hi Volker Kuhlmann and Richard Nelson, As both of you are interested in where I got up to with getting my Dynamix 1000 VA UPS working with Linux, here is the details. It works.. But not too well, as the driver still seems to need some work, and is not in the main nut source as far as I know. It also seems to sometimes not respond when it should. The manufacture has uses the same format as

Hello, I have just installed nut_2.6.0 from Debian testing, do anyone know the correct driver for this ups? The blazer_usb don't report battery-charge, the bundled software report charge and runtime. root at pluto<~>upsc powerwalker battery.voltage: 40.86 battery.voltage.nominal: 36.0 beeper.status: enabled device.mfr: device.model: HV 1K device.type: ups driver.name: blazer_usb

R-help, I'm getting some unexpected behavior with subsetting a data frame (aircraft flight data) that I can't sort out. Here is a simplified version of my data frame and problem: > flight FlightID TailNo FlightDate HobbsTime FlightCost Date year 1 4497 6009K <NA> 2.2 330.0 <NA> NA 2 4498 6009K <NA>

Hi, I'm at my wits end and need help regarding my UPS. I am a newbie to Linux (10 months) and need help with trying to configure my UPS to my Linux SME server. I have little or no experience with Bash and am finding it overwhelming when it comes to trying to configure my UPS. I have installed my UPS to my Linux SME server and have installed my driver for it. At best I think its running but

Can anyone work out why my callerid doesn't work on my isdn4Linux with asterisk (or without asterisk for that matter)... This used to work fine, and I am quite confident that the telco is sending callerid information (because they always do on all ISDN lines standard, only extra cost on POTS lines). This is the information from dmesg, whether asterisk is running or not: isdn_net: Incoming

Hi again, > On Sep 8, 2016, at 10:05 AM, Vassilis Virvilis <vasvir at iit.demokritos.gr> > wrote: >> Now that's a problem. I am not sure that I can find >> >> 1) the original software >> 2) a (physical) windows machine in the vicinity of the UPS >> Ha! I jumped several hooks but I think I got it. 01. I contacted the store that sold us the UPS and

Hi, I'm using a gamasonic UPS with a megatec driver since two years with no problem. I'm running a Linux server Debian Etch 4.0 and the nut package is ( taken from dpkg -l nut ) ii nut 2.0.4-4 The core system of the nut - Network UPS Tools Today morning I found the UPS powered off. I had to manually power it on. I found the following