similar to: PowerCOM UPS management protocol specification

On Mon, 15 May 2017, Dinow Hsieh wrote: > ==> I have tried this command "upsdrvctl shutdown" as below results (However the UPS still sustain the power) > > ??? Network UPS Tools - UPS driver controller 2.7.1 > ??? Network UPS Tools - Generic HID driver 0.38 (2.7.1) > ??? USB communication driver 0.32 > ??? Using subdriver : PowerCOM HID 0.4 > ??? Initiating UPS

Good Day Roger Price AA. Hi, Normally one would expect the UPS to disconnect it's power outlets after the default ups.delay.shutdown = 20 seconds. ==> I got it. I tried to command "upsdrvctl shutdown" on both line-mode and battery-mode ==> But ups do not disconnect its outlets power ----------------------------------------------------------------------------------- BB.

Good Day Roger AA. notice that during the test, you have little or no load, since despite being in state OB DISCHRG the battery.charge is still 100. It's best to perform such tests with a dummy load such as a table lamp and an old fashioned incandescent 100 watt bulb. ==> Yes. I got it and try to ascend load as below results dinow-All-Series:~# upsc pcmups Init SSL without

Hi! Is there any user of nut having this type of UPS? ( http://www.pcmups.com.tw/product/iCute.html) It works nice under windows and also is detected under Linux and installed as USB HID device. There is problem however, as the software provided by its manufacturer (http://www.pcmups.com.tw/download/Download/UPSMON_USBV091.zip) doesn't seem to comunicate with the UPS at all. It shows messages

Good Day nut Many thanks for your reading ==> AA. I confront an issue that can't shutdown the ups With the nut, I can get the ups status(upsc) and shutdown the linux-ubuntu when power failure occurs(upsmon) But don't know which configuration I ignore to setup for ups shutdown ==> BB. I want to check that with the command "upsdrvctl shutdown" and

resending to the list - got an error the first time. From: Charles Lepple <clepple at gmail.com> Subject: Re: [Nut-upsuser] Re Powercom Vanguard driver for nut Date: July 21, 2012 1:21:22 PM EDT To: Gordon Longland <gordon at compsos.com.au> Cc: nut-upsuser at lists.alioth.debian.org <nut-upsuser at lists.alioth.debian.org> On Jul 21, 2012, at 7:52 AM, Gordon Longland wrote:

Hello there! I know, that this thing is discussed many times already ( http://xen.1045712.n5.nabble.com/change-console-size-of-quot-xm-console-quot-td2572700.html for example), but still can''t figure out a reason, why the possiblity to dynamically change HVC size can''t be totally implemented for a many years :''(. _______________________________________________

Hello there! I know, that this thing is discussed many times already ( http://xen.1045712.n5.nabble.com/change-console-size-of-quot-xm-console-quot-td2572700.html for example), but still can''t figure out a reason, why the possiblity to dynamically change HVC size can''t be totally implemented for a many years :''(. _______________________________________________

Good Day Roger AA. notice that during the test, you have little or no load, since despite being in state OB DISCHRG the battery.charge is still 100. It's best to perform such tests with a dummy load such as a table lamp and an old fashioned incandescent 100 watt bulb. ==> Yes. I got it and try to ascend load as below results dinow-All-Series:~# upsc pcmups Init SSL without

Hello everybody! I'm trying to use nut-2.4.1 with brand new UPS Powercom Imperial IMD-825AP USB. I've faced a problem that the driver powercom despite specifying type=IMP automatically re-detects the UPS as "KIN" and then interprets raw data incorrectly. The same problem was reported by other Powercom users on the official support forum ( http://forum.pcm.ru ). I suppose the

Hi Have been trying to get nut and Powercom Vanguard 2000 ups communicating ? in the /lib/udev/rules.d/52-nut-usbups.rules file we have this entry #? PowerCOM VGD - Vanguard? - usbhid-ups ATTR{idVendor}=="0d9f", ATTR{idProduct}=="0004", MODE="664", GROUP="nut" ? In the /etc/ups/ups.conf [UPS] ??????? driver = usbhid-ups ??????? port =

Hello, Got PowerCOM BNT-1000AP, usb id 0d9f:00a6, firmware FW4.A6 nut 2.4.3 on debian stable shows only two instant commands: beeper.toggle - Toggle the UPS beeper -- not working test.battery.start.quick - Start a quick battery test -- works ok. No load and shutdown commands. Trying svn trunk version, with the same results. Debug output shows the problem: 0.035558

I'm trying to use NUT with PowerCom RPT-1000AP on CentOS 6/7 ups.conf: [RPT-1000] ??? driver = "usbhid-ups" ??? port = "auto" ??? vendorid = "0D9F" ??? productid = "0004" ??? product = "HID UPS Battery" ??? serial = "004-0D9F-000" ??? vendor = "POWERCOM Co.,LTD" ??? bus = "002" ??? pollfreq = 10 ??? offdelay = 120

On Tue, 16 May 2017, Dinow Hsieh wrote: > BB. Could you show us the output of command "upsc pcmups"? > > ==> Yes. Below 2 mode were the outputs of command "upsc pcmups" > > battery.charge: 100 > battery.charge.low: 10 > battery.charge.warning: 30 > battery.date: 2010/12/20 ... > ups.date: 2010/12/20 > ups.load: 4 ... > ups.status: OB

On May 17, 2017, at 4:53 AM, Dinow Hsieh <dinow at upspowercom.com.tw> wrote: > > ==> I tried below set-command but it react fail > > dinow-All-Series:~# upsrw -s "ups.delay.shutdown"="30" -u pcmups pcmups at localhost > Password: > Unexpected response from upsd: ERR ACCESS-DENIED > This error is not from the driver. Be sure to specify a NUT

Hi there! I just fresh-installed Xen on new server, Xeon E5-2620, and noticed following thing: node1 ~ # xl info -n host : node1 release : 3.8.8 version : #1 SMP Tue Apr 23 20:54:17 MSK 2013 machine : x86_64 nr_cpus : 6 max_cpu_id : 5 nr_nodes : 1 cores_per_socket : 6 threads_per_core

Hi guys, We've got a BNT-1000AP (powercom) BlackKnight UPS that works with the KIN1500AP model in the powercom driver. Well, almost. It seems the input frequency and the battery charge is swapped around: # upsc blackknight at localhost battery.charge: 46.5 driver.name: powercom driver.parameter.manufacturer: BlackKnight driver.parameter.modelname: BNT-1000AP driver.parameter.port:

OS name and version: pi at raspberrypi ~ $ cat /etc/*release PRETTY_NAME="Debian GNU/Linux 7.0 (wheezy)" uname -a Linux raspberrypi 3.6.11+ #393 PREEMPT Fri Mar 8 16:36:28 GMT 2013 armv6l GNU/Linux exact NUT version pi at raspberrypi ~ $ dpkg -s nut Package: nut ... Version: 2.6.4-2.3 NUT installation method: package exact device name and related information:

On 04/20/2015 02:01 PM, Rowland Penny wrote: > > I would suggest you try it on a test set up in a VM and if it works, go > to production. > > Rowland > Hi Rowland, Ok, I think I am pretty close. Still using Samba 3.3.6 since I couldn't seem to get Samba 4 to work from backports. My sticking point right now is that winbind is mapping the wrong UID to my test user.

Hello all, I've just installed Samba 3.6.6 from the Debian Stable repo. I want to use this linux box as a smb file server for windows clients. I installed NSLCD to allow users in AD to authenticate against my linux server per https://wiki.samba.org/index.php/Local_user_management_and_authentication/nslcd getent passwd and getent group returns domain users with UID mappings like: tempuser