similar to: [Nut-upsuser] Belkin F6C1100-UNV

Hi, it'd be great if you could update the documentation on the website that some models of the Belkin -UNV series will only work with the megatec(_usb) drivers. I wasted a lot of time on trying to get it to work with the wrong drivers, and would like to spare others the pain :-). Thanks, ~David P.S. Some forum post said that the stable megatec drivers don't work 100% with the belkin UPS,

Hi, it'd be great if you could update the documentation on the website that some models of the Belkin -UNV series will only work with the megatec(_usb) drivers. I wasted a lot of time on trying to get it to work with the wrong drivers, and would like to spare others the pain :-). Thanks, ~David P.S. Some forum post said that the stable megatec drivers don't work 100% with the belkin UPS,

All, I just bought a Belkin F6C1100-UNV and am trying to get it to work with NUT. I have tried many drivers ( "belkin", "belkinunv", "genericups upstype=4", and "genericups upstype=7", "bestups", "fentonups"). None of them seem to work. Does anyone have any experience with this device? If there is some utility that you all use to

Hi everyone, I have a belkin ups that was bought around 2 months ago. It seems like the driver doesn't like the UPS, although on the website it's listed as supported. This is on a gentoo system with nut 2.2.1 . megatec_usb output: ---------SNIP---------- digamma nut # ./megatec_usb -a belkinm -DDDDDD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues

Mr. Selinger, I'm CCing you directly since it appears (insofar as I can tell) that you are one of the delelopers for the newhidups driver. This is the third time I've submitted this (hence the CC this time). Hopefully mailman takes it. I've tweaked my SPF records, and I'm hoping that was the problem. My sincere apologies if this has gone through and I just haven't seen it

Hello, all, I had been using NUT's Ubuntu package (64 bit) with no problems until upgrading to Ubuntu 11.04. Now, I get the following message when I try usbhid-ups: $ sudo /lib/nut/usbhid-ups -a mybelkin Network UPS Tools - Generic HID driver 0.35 (2.6.0) USB communication driver 0.31 Can't claim USB device [050d:1100]: could not detach kernel driver from interface 0: Operation not

Hi. My Belkin UPS F6C1100-UNV works fine with megatec_usb version 1.6 (2.4.1). However, it doesn't work with 2.4.2 nor 2.4.3. # /lib/nut/megatec_usb_old -D -a belkin Network UPS Tools - Megatec protocol driver 1.6 (2.4.1) Serial-over-USB transport layer 0.10 debug level is '1' Starting UPS detection process... 0 out of 5 detection attempts failed (minimum failures: 2). Cancelling

Philipp Leusmann wrote: > > Ok, I tried this and my results seem to bet he same as reported. Then I > think I=B4ll have to stick with the windows-driver at least on my main > machine.=20 > Or is there anything I can help to fix this driver? I don't know why we can't read anything from this device. There are many ways in which one could make a buggy device that works with

I think someone tried this recently, although I cannot find the post any more. It may be helpful, but it is not guaranteed that we will find anything. Could you please keep the discussion on the mailing list? Thanks, -- Peter Philipp Leusmann wrote: > > Wouldn't it help to sniff usb-communication with the windows driver? > > Philipp > > > -----Urspr=FCngliche

I recently installed NUT 2.2.1 and set it up with a Belkin F6C100-UNV. I can monitor it via serial (belkinunv) or USB (usbhid-ups) cable, and both do seem to work fine, but I would prefer USB to avoid having to add a PCI serial card to the machine. I had to unplug something else to try it with a serial cable. Using 'belkinunv', there's a "-x wait" option: [ from

I have a new Belkin F6C900-UNV. I see that it's not listed in belkin-hid.c The VendorID is 0x050d like all the Belkin UPSes, and the ProductID is 0x0900. I haven't had a chance to actually test the development version of nut yet, since I'm running Fedora Core 6, which still has nut 2.0.3. `newhidups -DD -a myups` gives the error of: Checking device (050D/0900) (001/002) - VendorID:

I just moved my UPS over from serial to USB and found that I needed to add it to the hotplug USB list to make things work. Belkin F6C120-UNV - Bus 002 Device 004: ID 050d:0912 Belkin Components It seems to be working OK on 2.0.4 with newhidups. Attached is a patch which I think should add the appropriate device id's in the right places to the trunk code. Jon -------------- next part

This model is available in AU/NZ and can work as USB or serial. It uses the cutdown Bulldog software that comes with the cheaper serial based belkin models, and they don't officially support the USB mode under Linux. Anyone managed to get this working with NUT using either serial or USB? I'd really like to get the extra functionality of the NUT tools vs the very simple setup of the

Hi, I've been fighting with trying to get a Belkin Universal model F6C800-UNV to work with NUT. The error I am getting is as follows: ---------------------------------------------- * Starting UPS drivers ... Network UPS Tools - UPS driver controller 2.0.0 Network UPS Tools - Belkin 'Universal UPS' driver 0.06 (2.0.0) tcgetattr(/dev/ups): Inappropriate ioctl for device Driver failed

Greetings! Thanks to all the developers who have made this project so far. Searching for a Linux based Belkin UPS monitor led me straight to the Network UPS Tools. I have bought a Belkin F6C900-UNV (900VA) for use on a Slackware 10.2 server to replace an older APC model that died suddenly. So far I have successfully managed to get NUT 2.0.5 compiled and configured and found that this Belkin

I recently upgraded from nut-2.4.1 to 2.4.3 and my UPS stopped working. usbhid-ups now fails two communicate with the UPS: With 2.4.1: # /sbin/usbhid-ups -D -a auto Network UPS Tools - Generic HID driver 0.34 (2.4.1) USB communication driver 0.31 debug level is '1' upsdrv_initups... Using subdriver: Belkin HID 0.12 Path: UPS.BELKINConfig.BELKINConfigVoltage, Type: Feature, ReportID: 0x01,

I'm trying to set up a belkin f6c1100-unv UPS to work with nuts. From reading the mailing list, it sounds like the belkinunv serial driver should work and that the USB driver is potentially troublesome. Is this a correct impression? Also I may have missed this but if I do go with the serial (or USB port) is there any simple command line method for verifying basic connectivity? The

Marc Collin wrote: > > Le mercredi 27 d=E9cembre 2006 00:29, vous avez =E9crit=A0: > > Hi Marc, > > > > the answer to your question is contained in the file INSTALL, > > distributed with NUT, section 6 "Set ownership data and permissions on > > your serial or USB ports that go to your UPS hardware." > > > > Quote: > > > >

Hi I'm sending this to you as it appears that you are the person who looks after and/or supervises the code for NUT's Belkin drivers. I'm using the address you use for the Nut-upsdev mailing list ( selinger at mathstat.dal.ca ). Anyway... I have a Belkin Universal UPS and, having just upgraded my Fedora Core system from 4 to 5 and had to go back through the system RC files

OK Eric, Den Tuesday 22 May 2007 08.56.08 skrev Eric S. Raymond: > Kjell Claesson <kjell.claesson at epost.tidanet.se>: > > Or install the udev rules and replug the ups. > > Did that. Manual startup of the driver now works without -u root, > indicating (I think) that the udev rools are doing their job. This >