similar to: Fenton UPS driver -- unknown UPS report

Hi! I've tried the Fenton Driver for my UPS. The Powercom driver doesn't work. Here is the results: Network UPS Tools - UPS driver controller 2.0.0 Network UPS Tools - Fenton UPS driver 1.21 (2.0.0) Unknown ups - please report this ID string: #PCM SMK-1000 2001 V9.0 Detected Unknown MK-1000 on /dev/ttyS0 Have you any ideas to make it compartible with NUT. Thanks! With

Hi list here is the patch to make fentonups recognize some PowerCOM's UPS's, and to setup terminal lines for them (at least for SMK-1500a) as powercom's original upsmon do. fentonups -x powercom works correctly with SMK-1500a (it screamed ''Communications with UPS lost - check cabling' or 'Short read during UPS id sequence' without this patch). Sorry for

Hi ups-devel, As I looked throw www.networkupstools.org site, haven't found any pointers where to send patches, so I hope this is the right place. (Please let me know weather this is the right place.) The patch contains a minor change in the logic of the driver, our Effekta MHD 3000 UPS continuously writes status data to the serial port, so one has to send a CR character and empty the

Hi there Would anybody happen to know the correct driver for a Fenton Powerpal S series? upsdrvctl reports: Network UPS Tools - UPS driver controller 1.2.2 Network UPS Tools - Fenton UPS driver 0.90 (1.2.2) Unknown ups - please report this ID string: #FENTON S Series V4.04EG503 Detected Unknown Series on /dev/ttyS0 Alternatively, does anyone know if the manufacturer is likely to

Hi There, Running on debian sarge. This was working a while ago, but here goes.. When viewing the upsstats.cgi page, im getting a message "Not Supported" in the Model column with a "ONLINE" message, but no other stats. Here is the syslog when booting nut: Oct 15 14:28:40 mx1 upsmon[4835]: Signal 15: exiting Oct 15 14:28:40 mx1 upsmon[4834]: upsmon parent: read: Success Oct

Hi Henning, you should get in touch with Carlos, who his developing a generic megatec driver (available from svn: http://eu1.networkupstools.org/source.html) Arnaud -- Linux / Unix Expert - MGE UPS SYSTEMS - R&D Dpt Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer - http://people.debian.org/~aquette/ OpenSource Developer -

Hi, I am working on a patch for FENTON.H to support some more ups models, I wonder if someone can help with further information,meaning and importance for the following values that are beeing set in the model capability table: float lowvolt; float voltrange; float chrglow; float chrgrange; int lowxfer; int lownorm; int highnorm; int highxfer; Thanks, Nadav

Carlos, Today I was browsing through the NUT Tracker and noticed an entry which linked to a message on nut-upsdev: http://lists.alioth.debian.org/pipermail/nut-upsdev/2006-January/000559.html Although the fentonups driver is no longer in the tree (since it was replaced by the megatec driver), I think there is still some merit in this patch. Notice the following lines from this message: >

Hello everybody, this is my first post to this list - normally I take some time to read some messages first to get an impression of the List, but I have a pressing question to ask, so please forgive me if I miss the right tone... I just installed NUT 2.0.2 and try to get it working with our Effekta MT 1500. In the Drievers List I found this entry: "Effekta" "MI/MT/MH"

Hello, The following code is expected to produce 4 charts. But, I only get charts 1,2 ,& 4, NOT CHART # 3. For Chart# 3, I am getting the following error message: Error in tapply(1:NROW(x), list(factor(strata)), function(index) { : arguments must have same length I would appreciate if someone could help me resolve the issue. Thanks, Pradip # BELOW IS THE REPRODUCIBLE EXAMPLE setwd

Hi, I have a Fenton Powerpal L660, when I try and configure nut with either the metatec or fentonups driver, and start upsd, the UPS instantly turns itself off. It used to work, until I changed my motherboard and CPU, which means it has a different bios and serial port setup. This is happening with Nut 2.0.1 and also Nut 2.0.5. I have an AMD64 bit processor, Mandriva 2007 64 bit. Any

Hi Stefanos, you should mail to the NUT list, and try the megatec driver, which is only available from subversion for the moment (but should be included in the next stable release). Carlos might give you some help with this driver. Arnaud Quette -- Linux / Unix Expert - MGE UPS SYSTEMS - R&D Dpt Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer -

Hi There, i have a strange problem with a fenton powerpal 660. When you switch off the power to the UPS (from the wall), the server (IBM xSeries 203) attached to it dies...However, if you unplug the cable from the server to the UPS and plug it back in again (with the power still out to the UPS), the server starts up again (set to power up after a power failure) and runs with no issues. I have

Hi guys, Please bare with me, as this is my first attempt at setting up a UPS under Linux. I've been trying to setup a UPS on one of my clients servers. The model of the UPS is a Square one QP1000/QP1010 1Kva I've looked on the following link http://eu1.networkupstools.org/compat/stable.html It says that it should be compatible with the "powermust" driver, then in my

hey guys I finally got starcraft working (only took about two hrs, not bad) anyways I've played though it a bit and I get the first cinematic but I'm dropped back to X with this message "Starcraft was unable to open a required file, if the problem persists reinstall blah blah blah" the thing is it's trying to open PreTerran_1.smk in the smk folder.......but I don't have

Hi Patrick, 2006/4/2, Patrick Beard <p.beard@blueyonder.co.uk>: > Hi Arnaud, > > Just wanted to let you know the the Belkin F6H500ukUNV is working for me > with the fentonups driver. > > http://catalog.belkin.com/IWCatSectionView.process?IWAction=Load&Merchant_Id=&Section_Id=202840 > > I originally tried it with the genericups driver with upstype=7 but this

Hi everybody, I've got an Unitek iZi UPS 525 with a serial interface. The supplied cable looks fairly simple: RX->RX , TX->TX and GND->GND. Using this cable and Minicom with 2400 8N1 I'm able to issue commands to the UPS using the "Megatec Protocol" http://www.networkupstools.org/protocols/megatec.html so I know the UPS is fairly "intelligent" :-) and the

2007/2/19, Glen Ogilvie <nelg@linuxsolutions.co.nz>: > Hi, > > I have a Fenton Powerpal L660, when I try and configure nut with either the > metatec or fentonups driver, and start upsd, the UPS instantly turns itself > off. > > It used to work, until I changed my motherboard and CPU, which means it has > a different bios and serial port setup. > > This is

2007/2/19, Glen Ogilvie <nelg@linuxsolutions.co.nz>: > Hi, > > I have a Fenton Powerpal L660, when I try and configure nut with either the > metatec or fentonups driver, and start upsd, the UPS instantly turns itself > off. > > It used to work, until I changed my motherboard and CPU, which means it has > a different bios and serial port setup. > > This is

Hi *Simon, i got a similar setup here (also a powercom-oem-product, but in my case labeled by a swiss "manufacturer") with the same problems, using powercom's upsmon works fine, while nut completely refuses to cooperate. after trying almost everything i somehow hopeless surfed on the official nut-page, when i saw that there are powercom-products which don't need the