similar to: Fw: INFOSEC 500 XP en USB et drivers newhidups avec '-x generic'

Hi Arnaud, Is there any news about this hardware,does nut managed it right now ? Is there any technical information to make it working on debian ? Thanks for your help, Regards, DaneZ _____ From: Arnaud QUETTE [mailto:Arnaud.QUETTE@mgeups.com] To: DaneZ [mailto:david.guillotte@danez.no-ip.org] Sent: Mon, 17 Jul 2006 09:07:03 +0200 Subject: Re: RE Fw: INFOSEC 500 XP

So, I have this Mustek Powermust 600USB (no serial port) here temporarily. It seems to be a hid device. The output from "lsusb -v" and "newhidups -DDDDD" (with "generic" and "vendorid=06da") are (respectively): ----------------------------------------------------------------------------------------------- Bus 001 Device 002: ID 06da:0003 Phoenixtec Power

I used a brazilian UPS from "TS-Shara" which uses the megatec serial protocol and it works perfectly. Now I have another one from the same brand (TS-Shara) and it uses a USB cable. I found the following: T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3 Spd=1.5 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1 P: Vendor=0483 ProdID=0035 Rev= 2.00 S:

I looked through the faq, but couldn't find an answer to this. I'm trying to configure nut-2.0.4-26 on SuSE linux 10.2. In ups.conf, I have [myups] driver = belkinunv port = /dev/undefined desc = "Local UPS" I'm trying to find out what the port should be set to. lsusb shows: Bus 001 Device 005: ID 050d:0980 Belkin Components Device Descriptor: bLength

Hi everybody, In a christmas sequel I've been offered one of the units mentioned above. I've tried to connect it to my Fedora 8 workstation but rapidly concluded it's not yet supported by NUT. So far, I've decompiled the Java classes of the manufacturer's application and noticed that it's most probably yet another kind of serial protocol through the USB. Since

Hi, I'm new in the list and I'm having a little bit trouble to put the megatec_usb to work. I've been using NUT for a while with the apc and megatec driver (serial), with no problem. The server is a Ubuntu 8.04.2 with NUT version 2.2.1-2.1ubuntu7.2, the default package version in this ubuntu release. I've configured the ups.conf as follows: [sms] driver = megatec_usb

Hi, I'm new in the list and I'm having a little bit trouble to put the megatec_usb to work. I've been using NUT for a while with the apc and megatec driver (serial), with no problem. The server is a Ubuntu 8.04.2 with NUT version 2.2.1-2.1ubuntu7.2, the default package version in this ubuntu release. I've configured the ups.conf as follows: [sms] driver = megatec_usb

Hi all, I?ve a UPS Liebert GXT3 500-3000VA with USB port. I?ve install NUT version 2.2.2 from repository packages for Debian Lenny. Linux kernel 2.6.26 I?ve try to use usbhid-ups driver in ups.conf [liebert] driver=usbhid-ups port=/dev/usb/hiddev0 Debian get the usb: # lsusb -v Bus 001 Device 002: ID 10af:0008 Liebert Corp. PowerSure Interactive UPS Device Descriptor: bLength

Hi Arjen My apologies fro drifting off topic in the other mailing list...:-) On the bottom of the Belkin UPS unit - is the model number: F6C120auUNV The "au" is for Australia I think. "man belkinunv" states that F6C120-UNV is supported - and I assumed that the "au" would not prevent this. I plugged in the USB to gather the information you requested. My intention

Ok guys I get this errors: Network UPS Tools ? UPS driver controller 2.4.1 Network UPS Tools ? Generic HID driver 0.34 (2.4.1) USB communication driver 0.31 No matching HID UPS found my ups.conf is: [ap1000] driver = usbhid-ups port = auto I?ve also tried to set a specific usb port and change driver. My ups is a AMACROX 1000 http://www.amacrox.com//english/01_product/02_01detail.aspx?pdid=46

I have an UPS, that claims to be IPPon Back Power Pro 700. I'm trying to connect it using USB. lsusb -v says: Bus 1 Device 3: ID 06da:0003 Phoenixtec Power Co., Ltd Device Descriptor: bLength 18 bDescriptorType 1 bcdUSB 1.10 bDeviceClass 0 (Defined at Interface level) bDeviceSubClass 0 bDeviceProtocol 0

>> >> The output was also not as big as you made it out to be. > > Well, I didn't expect the driver to fail *that* badly :-) > > Assuming the UPS is still at /dev/ugen4.2, can you try the following command? (Probably needs to be run as root, with the driver stopped.) > > usbconfig -u 4 -a 2 dump_curr_config_desc Here is output of the command. Thank you for

On 06/19/2017 05:33 PM, Charles Lepple wrote: > On Jun 19, 2017, at 4:27 AM, Manuel Wolfshant wrote: >> 1.014501 [D2] Unable to get HID descriptor (Pipe error) >> 1.014511 [D3] HID descriptor length (method 1) -1 > So at this point in the logs, the kernel USB HID driver is detached from the UPS HID interface (until the UPS USB cable is unplugged and reattached). If

Hi, Sometime ago [ June 2018 ] I posted a message about getting trying to get NUT to work with a Power Shield Defender 1200VA UPS. This model appears in the HCL at https://networkupstools.org/stable-hcl.html That UPS reported the following when queried using 'lsusb' on an iMac running macOS [ 10.15 ] Bus 001 Device 008: ID 0665:5161 Cypress Semiconductor USB to Serial Device Descriptor:

Hi nut-upsdev, I have just got OMRON BX35F. Only object files and usage information is included. Where should I start to help you to get it supported? Any interest in supporting it at all?

I recently purchased a UPS from http://www.microcenter.com/product/470131/5E_1,100W_2,200VA_6-Outlet_UPS It's sold as an Eaton 5E 1,100W 2,200VA 6-Outlet UPS SKU: 147140 Mfr Part #: 5E2200USB-LA UPC: 743172064875 "The Eaton 5E is an essential line interactive UPS that provides cost effective and reliable power protection against power outages and bad power quality. Thanks to its small

Here are all the usbconfig outputs you have requested. I have left a message with the Dev for NAS4Free to give up the ./configure for NUT portion.? I am hoping they will... usbconfig -u 0 -a 5 dump_device_desc? datanas: ~# usbconfig -u 0 -a 5 dump_device_desc ugen0.5: <TRIPP LITE UPS Tripp Lite> at usbus0, cfg=0 md=HOST spd=LOW (1.5Mbps) pwr=ON (100mA)? bLength = 0x0012 ? bDescriptorType =

Following the instructions a following site I can not get nut to work with my UPS. http://bernaerts.dyndns.org/linux/75-debian/335-debian-wheezy-install-monitor-eaton-ups Hope that you can find out what is wrong by the provided info in the email Best Regards, Magnus Karlsson # lsusb -s 001:005 -v Bus 001 Device 005: ID 06da:0002 Phoenixtec Power Co., Ltd UPS Device Descriptor: bLength

Hi, I have a powermust with a usb connector. I searched the archive and found this post: http://lists.alioth.debian.org/pipermail/nut-upsdev/2006-April/000816.html Must I abandon hope of controlling this UPS via USB with NUT? Added this line to /etc/udev/rules.d/70-nut-usbups.rules: # OMRON - usbhid-ups SYSFS{idVendor}=="06da", SYSFS{idProduct}=="0003",

I was dropping off junk at the waste transfer station and scarfed a UPS out of the pile of old TV's and VCR's. It was in good physical condition and as I expected, the battery was toast. A new RBC-2 battery restored it to working condition. Then I tried to get it to talk to some software. And I am having no luck. The unit is branded as a Nexxtech Model 6118507 650VA imported into