similar to: Mustek Powermust 600USB and newhidups

Hi again, I've succeeded in compiling the svn trunk with the automake tools and wish to say thank you to Charles Lepple for his help. After fixing some parameters in the hotplug script I can now get access to the UPS on /dev/usb/hiddev0 (I added productid and vendorid of my ups to the usermap). I've decided to try the newhidups driver with -x generic parameter and got this response :

Hello all, I am trying to set up my brother's UPS (remotely over internet) on an OpenIndiana-based storage box. According to him, the UPS is probably an Ippon Back Power Pro 600 dated around 2003 (battery recently replaced), and it has an USB connection. Sorry for a relatively long post with a log of my successes and failures, in the hopes that someone would point out what I did wrong.

On 11/9/2013 5:24 AM, Jim Klimov wrote: > Hello all, > > I am trying to set up my brother's UPS (remotely over internet) > on an OpenIndiana-based storage box. According to him, the UPS is > probably an Ippon Back Power Pro 600 dated around 2003 (battery > recently replaced), and it has an USB connection. > > Sorry for a relatively long post with a log of my successes

Hi, I bought a Belkin Active Battery Backup UPS (http://www.belkin.com/uk/activebattery/) yesterday with a USB port and hoped it would work with nut. The device will show up in /proc/bus/usb/devices as a Cypress Semiconductor USB to Serial. It creates /dev/hiddev0 (and this disappears when the UPS is unplugged). I've tried using belkin, belkinunv, usbhid-ups and megatec_usb. I've tried

Hi, a few days ago, I bought some of those Mustek UPSes that have both a serial and a USB connector. Currently only the serial port is supported by the megatec driver. This works fine so far. Now I have seen there is a megatec_usb driver, which currently only supports 2 other UPSes. How can I help to find out whether the PowerMust might actually work with the megatec_usb driver? -- Regards,

Hi Rok, I retired from working on NUT a few months ago, so I don't have the most up-to-date info. But the guys on the nut-upsdev mailing list (cc'd above) are very helpful. Both of your devices (or nearly identical ones) have been seen on the mailing lists before. The Sweex was first mentioned in a message by Eli Wapniarski on 14 Jun 2006 on nut-upsuser, and was most recently discussed

Disclaimer: I've setup APC UPS monitoring and it works... ... but when it comes to mustek powermust 600usb (connected via com-port), I can't make it work. Got NUT installed via aptitude in ubuntu feisty and a basic setup, exactly the same as for the apc, except for the name of the ups and the corresponding section of ups.conf -- [mustek] driver = megatec port = /dev/ttyS1

Hello. So as my english is not so good, i'll try to write my story in bash commands :o) miwa@zork3$ uname -mrs FreeBSD 5.5-STABLE i386 miwa@zork3$ su root@zork3# cd /usr/ports/sysutils/nat root@zork3# make && make install root@zork3# cd ../nut-usb root@zork3# make && make install root@zork3# cd /usr/local/etc/nut root@zork3# cat ups.conf user=root [MGE-Ellipse]

A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 188 bytes Desc: not available Url : http://lists.alioth.debian.org/pipermail/nut-upsdev/attachments/20071124/3ceb35d2/attachment.pgp

Hi, I'm having a hard time configuring a Mustek Powermust 600VA ups to work via USB with nut. I read somewhere that nut works OK via the rs232 cable, but unfortunately I don't have a COM port in my computer. The kernel detects the ups as an Xbox pad :) and loads the xpad module. I tried running /lib/nut/megatec with different /dev/ttySx but it displays megatec protocol UPS was not

Hi, I have a powermust with a usb connector. I searched the archive and found this post: http://lists.alioth.debian.org/pipermail/nut-upsdev/2006-April/000816.html Must I abandon hope of controlling this UPS via USB with NUT? Added this line to /etc/udev/rules.d/70-nut-usbups.rules: # OMRON - usbhid-ups SYSFS{idVendor}=="06da", SYSFS{idProduct}=="0003",

Have recently purchased a MGE Nova 1100 UPS and am trying to get running on netBSD. Configuration netBSD 3.0 amd64 libusb 0.1.10a nut 2.0.3 Built & installed libusb Built kernel with ugen device and uhid removed Build & install nut-2.0.3 with usb Chmod /dev/ugen1 etc to allow access by nut user. Ups.conf [MGENova] driver = newhidups port = auto

Hello, fisrt, you should subscribe to the NUT user mailing list to get a good support, since I've personaly no knowledges about such units: http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser Next, you should try the latest nut release (2.0.5 currently, but 2.2.0 soon) and most of all the new megatec driver. 2007/6/10, esva2 at inbox.lv <esva2 at inbox.lv>: > Dear

Arnaud Quette wrote: > Anyhow, I would more see this as a merge of all these drivers, with > some autodetection or flag/param to switch the mfr/model and maybe > capabilities... Whatever the driver name is, a good thing would be the > name of the protocol or something generic enough, though powermust is > fine. Ok, I made some minor changes to powermust, to make it less

On 2/27/07, Markus Layr <tuxian@yahoo.de> wrote: > do you now if there is a possibility to get an connection betwenn nut an > the Mustek PowerMust 2000VA via USB? > I tried if with newhidups but I always got "No matching HID UPS found". In the latest development version of NUT there's a new driver called "megatec_usb" that may support your UPS. If it

Hi Vitaly, 2009/2/26 Vitaly Polyakov <var at fapu.ru> > Hello. > > You are the site administrator Project Network UPS Tools, are not you? I > think? it is a good idea to add information about the compatibility the > NUT with a Mustek PowerMust 424/636/848 USB. These UPS are using > modified protocol, and therefore the old driver megatec_usb is not > suitable and the

Hello, I'm trying to setup my UPS using the "megatec" driver, but for now without success. from what I understood, the UPS should be connected to serial port (despite being an USB UPS), so I did i. sudo upsdrvctl start Network UPS Tools - UPS driver controller 2.0.5 Network UPS Tools - Megatec protocol driver 1.5 (2.0.5) Carlos Rodrigues (c) 2003-2006 Megatec protocol UPS not

ok, I'll try to sum up the thread and answers to the various point: 2005/10/24, Peter Selinger <selinger@mathstat.dal.ca>: > > Arnaud Quette wrote: > ... > > Any perl (or other well supported scripting) monger out there to take > over > > that one? > > Great idea. How about bash/sh? Still the most universally available > scripting language. I am

Hello, We are using the equipment "MUSTEK PowerMust 3000 NetGuard RM". That is using Megatec protocol. But unfortunately not all the data can be viewed correctly when dumping from utility "upsc". For example: upsbox# upsc mustek at localhost battery.voltage: 108.00 battery.voltage.nominal: 96.0 driver.name: megatec driver.parameter.pollinterval: 2 driver.parameter.port:

On Jan 2, 2012, at 10:51 AM, Vladimir Micovic wrote: >> Bus 003 Device 004: ID 0665:5161 Cypress Semiconductor USB to Serial > Unfortunately, this device ID is used by several different vendors. What does "lsusb -vvv -d 0665:5161" show? > Also, what OS and kernel are you using? (I thought certain kernels had USB-to-serial drivers for that chip.) > -- > Charles