similar to: Unitek UPS driver/Rewrite of energizerups using libhid

Hello, I've already written to the list before about my non-standard hid Unitek UPS. I've tried to use hiddev to access my UPS as its USB HID interface is the same as the energizerups. Nevertheless, the protocols are different and I didn't manage to communicate with my UPS through hiddev. Moreover, the problem described in this page http://www.vttoth.com/ER-OF800.htm about the Linux

Hello, I would like to know if it's possible to use nut with a Unitek Alpha 650ip* and if it's possible which driver should I use ? Thanks.

Hi, I'm new to NUT. I've installed Fedora 8 and NUt along with it. I'm now having a go at getting my Unitek Alpha 1200sx UPS to work and shutdown the box automatically. I know this isn't officially supported but I'm trying my luck... I've seen that other Unitek UPSs use the 'megatec' driver however I'm unsure whether this will do the trick. My UPS comes with a

Do you know some piece of code I could look at to see learn more about this ?

Do you know some piece of code I could look at to see learn more about this ?

I've just acquired a Unitek ALPHA 1200 Sx UPS to replace an older serial UPS that's been working well with NUT for years. Could anyone with a Unitek tell me what the pinout on the 10P10C plug is so I can make up a cable? Thanks.

UNITEK Alpha650ipF and Alpha650ipE Build NUT v2.6.4 from sources http://www.networkupstools.org/source/2.6/nut-2.6.4.tar.gz System: RedHat Linux RHEL4 Kernel: 2.6.9-42.0.10.EL (upsc) command output : battery.charge: 100 battery.voltage: 14.30 battery.voltage.high: 13.00 battery.voltage.low: 10.40 battery.voltage.nominal: 12.0 device.mfr: UNITEK device.model: Alph650ipF device.type: ups

Hello I've got an Unitek UPS (650ipE) that use megatec driver ... I'm running Ubuntu 7.04 with a 2.6.20 kernel and nut 2.0.5-1 package Ubuntu by default use Udev and "hid", "usbhid", "evdev" kernel modules are loaded automatically The UPS is detected on system level but "upsdrvctl" can't access to the device ... Does anyone could give

Hi again, I tested several times using the Megatec driver from nut 2.2.2 to no avail, as it definitely never "sees" the UPS. Always getting : # drivers/megatec -DDD -a Alpha Network UPS Tools 2.2.2 - Megatec protocol driver 1.5.14 [megatec] Carlos Rodrigues (c) 2003-2008 debug level is '3' Starting UPS detection process... Asking for UPS status [Q1]... Q1 => FAILED

Hello everyone, has anyone ever tried to make this device work with Linux and NUT? This is what udevadm monitor says: UEVENT[1215983089.652345] add /devices/pci0000:00/0000:00:0f.2/usb1/1-1 (usb) UEVENT[1215983089.652427] add /class/usb_endpoint/usbdev1.4_ep00 (usb_endpoint) UEVENT[1215983089.657975] add /devices/pci0000:00/0000:00:0f.2/usb1/1-1/1-1:1.0 (usb) UDEV

Hello to all list members, I'm trying to make my UPS work with nut-2.2.2 (using Debian Testing, but compiled from source code) for a week ago, with not success. It's a Unitek Alpha 1000Ps, and I supossed it would work with megatec_usb driver, as other Unitek models. It has an USB interface, and when I plug it into my system I've got this message: chopito:/home/jordi# dmesg | tail

Hi All, I am a newcomer to Nut, so firstly hello :-) I am keen to implement Nut and have been digging around most of the day to see how to get my two Unitek 1250xD UPS devices working. I have now managed to get nut installed (from source 2.2.0) and have (I think) success. I found a post here: http://lists.alioth.debian.org/pipermail/nut-upsuser/2007-December/003573.html which was

Hi All, I am a newcomer to Nut, so firstly hello :-) I am keen to implement Nut and have been digging around most of the day to see how to get my two Unitek 1250xD UPS devices working. I have now managed to get nut installed (from source 2.2.0) and have (I think) success. I found a post here: http://lists.alioth.debian.org/pipermail/nut-upsuser/2007-December/003573.html which was

Hi, Just a quick message to say thanks for this great piece of software. Is it possible to add the Unitek Alpha 500 isx to the list of working UPS? I have tried it this afternoon on one of our machines and it is detected allright using the megatec_usb driver. It worked on Ubuntu Server "Hardy Heron" 8.04.1 using nut v. 2.2.1-2.1ubuntu7.2 Cheers, Mathieu

Hi everyone, I've been using nut 2.0.3 for more than a year on a Unitek iZi UPS 525 (which is a rebadged Mustek). Everything worked fine and last week, when pressed by RENEL :-) I ran a battery test which showed the system to have 17min of back-up power (yes, still haven't figured out how to use upssched...) The system used for testing was an old PIII/500MHz/512KB cache, 256MB RAM (3 x

Hi, just try the Unitek Self Protek Mistral 1000ipF with nut and I doesn't work. How can I correctly configure it (if the driver support it). Best regards, In my dmesg: [42953293.620000] usb 1-2: new low speed USB device using uhci_hcd and address 7 [42953293.760000] usb 1-2: no configurations [42953293.760000] usb 1-2: can't read configurations, error -22 [42953293.880000] usb 1-2: new

Hi everybody, I've got an Unitek iZi UPS 525 with a serial interface. The supplied cable looks fairly simple: RX->RX , TX->TX and GND->GND. Using this cable and Minicom with 2400 8N1 I'm able to issue commands to the UPS using the "Megatec Protocol" http://www.networkupstools.org/protocols/megatec.html so I know the UPS is fairly "intelligent" :-) and the

Looking for ioctl() calls in the drivers, I noticed that the energizerups.c code looks a lot like a megatec protocol over a USB connection. It uses 8 bytes per packet, which makes it look like the agiler subdriver in megatec_usb. Do we know if there are people that use this driver now and that might be able to verify this? Best regards, Arjen -- Eindhoven - The Netherlands Key fingerprint - 66

Hi Viktor, Just to notify you that your energizerups driver is being removed from the NUT tree, as of 2.4.0-pre1. If you wish to see it entering the tree again, please contact the Development mailing list to talk about it. I do recall that you are not maintaining it anymore since you don't own such a unit anymore, so it's really a simple notification. Merry Christmas and happy New Year.

Hi! I don't know how I missed it before, but "bestups" seems to implement mostly the same protocol as megatec. Is anybody out there using this driver willing to try "megatec" to see if it works? AFAIK, the only difference seems to be the command that gets the UPS identification data ("I" on "megatec", "ID" on "bestups"), but