similar to: Fwd: Fun with TrippLite

Hi Charles and Jonathan, I am going through my over 300 unread NUT messages, and I just discovered this one from mid-December. At the time, I was trying to clean up the tripplite subdriver of newhidups, but never got the information I needed. I have enabled this driver now, but it is marked "experimental". The driver is still incomplete, in the sense that there are many unmapped device

Hey I recently picked up a couple SMART1000LCD TrippLite UPS's. These are similar to other usb ups's that have been mentioned on the list in the past few months. I tried a few patches posted last month and got some amount of success. That being said, I am thus far unable to get much love from the actual upsd itself. Any pointers in terms of what I may need to change or what help I can

I think I'm going to have the slightly rejigger the tripplite-hid.c driver to 'properly' support all of the data I know about it's outlets. A given UPS may have 'n' output loads. I could have 5, I could have 10, I won't know until I actually ask the UPS. But in order to use the hid to nut struct, I'm actually going to have to modify that struct dynamically, or

I'm read through the archives trying to figure out how to get a Tripplite SmartPro SLT 1500 configured with NUT using the USB interface (it also has a serial interface but I'd rather not). The thread which this link belonged to seemed most instructive: http://lists.alioth.debian.org/pipermail/nut-upsdev/2007-January/001656.html and I followed it as best I could. I'm running a

I?m setting up a new system and installed a new UPS with nut. System Specifics: OS: Debian 3.16.36 Nut version: 2.7.2 Install method: apt-get Device: TRIPPLITE SMART1300LCDT using usbhid-ups driver Problem: The output from upsc has a few incorrect values. They appear to be a matter of scale. root at server:/etc/nut# upsc tripplite at localhost Init SSL without certificate database

While working on the mge-hid subdriver, I wanted to add the 'beeper.mute' command. Unfortunately, the description I intended to use was used already by the 'beeper.off' instcmd: CMDDESC beeper.off "Temporarily mute the UPS beeper" Now of course we could add another instcmd 'beeper.reallyoff', but instead I would prefer to bite the buller and do the following:

These patches allow this device to function in nut.. diff --git a/trunk/drivers/tripplite-hid.c b/new/drivers/tripplite-hid.c index c36da98..dddd13c 100644 --- a/trunk/drivers/tripplite-hid.c +++ b/new/drivers/tripplite-hid.c @@ -71,6 +71,8 @@ static usb_device_id_t tripplite_usb_device_table[] = { { USB_DEVICE(TRIPPLITE_VENDORID, 0x2005), battery_scale_0dot1 }, /* e.g. TrippLite

Thanks, now I started getting messages from the list. As you advised, I renamed the mib file NETCARD.mib to Tripplite and ran command ./gen-snmp-subdriver.sh -H 10.200.254.39 -c public -n Tripplite Here is what it says: snmp_build: unknown failuresnmpget: Error building ASN.1 representation (Can't build OID for variable) COUNT = 0 / 0 Creating tripplite-mib.h Creating tripplite-mib.c Done.

Joel Peshkin wrote: > > I hacked in the following additonal changes... > > Index: newhidups.c > =================================================================== > RCS file: /cvsroot/nut/nut/drivers/newhidups.c,v > retrieving revision 1.1.1.1.8.6.2.21 > diff -u -r1.1.1.1.8.6.2.21 newhidups.c > --- newhidups.c 7 Nov 2005 22:14:20 -0000 1.1.1.1.8.6.2.21 > +++

Just started using NUT and having a problem. I'm not sure if it is even NUT that is causing the issue. I'm running the latest FreeNAS 9.3 release. Network UPS Tools upsmon 2.7.2. The UPS is a Tripplite SU6000RT4UHVPM with the SNMPwebcard installed. I'm trying to use the SNMPwebcard, not USB or Serial. I've updated the SNMPwebcard to the latest firmware version (see below). In

I am trying to get a TrippLite SU1500RTXL2Ua working with nut on Mandriva 2007.1, is there a particular version of nut needed to get this to work? At first I tried nut 2.0.5 (which came with 2007.1) but it wouldn't work, and then research showed it was an older version of nut. So nut-2.2.1-2 src rpm was pulled from Mandriva 2008.1, the binary rpm built, and nut and nut-server installed from

On May 12, 2017, at 10:06 AM, Mike <the.lists at mgm51.com> wrote: > > > OpenBSD 6.1/amd64 > nut-2.7.4p0 (from OpenBSD package) > UPS: Tripp-Lite OMNI1500LCDT > > I cannot get the driver for the UPS to load without error. > > Here are the commands, with the output, and the config files: > > ======================================================= > #

Hi Matt, first, note that Russell (Kroll) is retired for long. Support request should go to the NUT Users list, which needs subscription. 2010/6/23 matt <matt at mattevans.org> > Experts, > > I have gotten nut to work this evening, with usbhid-ups, and a small > addition to udev, on my new TrippLite SmartOnline model. I am on Ubuntu > 10.04. This is the 2U rackmount 800W

On Aug 21, 2017, at 1:35 PM, Whiteshell Tech <neil at whiteshell-tech.com> wrote: > > I ran it again on battery and upsd running, set upsrw ok and then shutdown.return gave an "ERR CMD-NOT-SUPPORTED" Odd thing is after running that I am getting random timed ups powering off for one or two seconds then turns back on even on battery. Server then starts shutting down. Some

On Feb 10, 2014, at 1:16 AM, ??? ????? wrote: > Thanks for you reply. Concerning the subscribtion list, I have earlier filled in the fields and sent request to subscribe to this list, but still haven't got an answer. I added you manually, but check your spam folder just in case it ended up there. > Yes, I do have a MIB file that was on CD that came with the UPS, attached it to this

On 5/13/2017 10:20 AM, Charles Lepple wrote: > On May 12, 2017, at 10:06 AM, Mike <the.lists at mgm51.com> wrote: >> >> >> OpenBSD 6.1/amd64 >> nut-2.7.4p0 (from OpenBSD package) >> UPS: Tripp-Lite OMNI1500LCDT >> >> I cannot get the driver for the UPS to load without error. >> >> Here are the commands, with the output, and the config

When running 'sudo upsmon -c fsd' UPS turns off then back on after a delay as expected. But when power is disconnected and the command is ran, the UPS turns off but still turns back on again. Changing 'ondelay' to -1 or 0 does not change the behavior. How can I get the UPS load to stay turned off if there is no power? Or am I misunderstanding how to test this functionality?

OpenBSD 6.1/amd64 nut-2.7.4p0 (from OpenBSD package) UPS: Tripp-Lite OMNI1500LCDT I cannot get the driver for the UPS to load without error. Here are the commands, with the output, and the config files: ======================================================= # upsdrvctl start Network UPS Tools - UPS driver controller 2.7.4 Network UPS Tools - Generic HID driver 0.41 (2.7.4) USB communication

Hi, With recent revision, it's impossible to get upsdrvctl started: [root at teevee nut]# /usr/local/bin/upsdrvctl start Network UPS Tools - UPS driver controller 2.3.0-1352 Network UPS Tools: 0.29 USB communication driver - core 0.33 (2.3.0-1352) Warning: This is an experimental driver. Some features may not function correctly. Using subdriver: TrippLite HID 0.2 (experimental)

Tripp Lite SMART1300LCDT # upsc ups battery.charge: 100 battery.charge.low: 10 battery.charge.warning: 30 battery.runtime: 2951 battery.type: PbAC battery.voltage: 0.0 battery.voltage.nominal: 24.0 device.mfr: Tripp Lite device.model: TRIPP LITE UPS device.serial: 2250AVLSM872100251 device.type: ups driver.name: usbhid-ups driver.parameter.pollfreq: 30 driver.parameter.pollinterval: 2