similar to: TrippLite OMNI1000LCD hiddev compatibility

Dean K. Gibson wrote: > > My Belkin UPS 1000 failed about a month ago; all of a sudden it > reported a battery failure. Since the Belkin logs showed this as in > instant transition from 99% to 22%, I assume a circuit board failure, > not a battery failure. Similarly, one Belkin UPS 500 circuit board > failed after I used my 100W amateur radio transmitter (not connected to

Joel Peshkin wrote: > > I hacked in the following additonal changes... > > Index: newhidups.c > =================================================================== > RCS file: /cvsroot/nut/nut/drivers/newhidups.c,v > retrieving revision 1.1.1.1.8.6.2.21 > diff -u -r1.1.1.1.8.6.2.21 newhidups.c > --- newhidups.c 7 Nov 2005 22:14:20 -0000 1.1.1.1.8.6.2.21 > +++

Nut shut down a machine last night when there was no power outage. When I came in this morning, the UPS was turned off, but it turned on cleanly and passed its self-test. The battery was at 62% when I first checked it, and it's up to 63% now, about 20 minutes later. The UPS is a Tripp-Lite AVR550U. I'm running nut version 2.0.3. I expect to be told to update to a newer version and to

Hello Nut Devs, I'm working with usbhid-ups and a Tripplite OMNI1000LCD. I used a USB packet sniffer to discover something cool about the watchdog feature in this unit. (not sure if the other OMNI-X-LCD models work the same or not.) Basically there's a single HID variable at Report ID 0x52 (UPS.OutletSystem.Outlet.ffff0092) that's one byte (0-255 int) and it contains the Watchdog

Hello NUT-UPSUSERS, I would just like to try and help other and indicate that I was able to use the development trunk and get the Tripp Lite OMNI1000LCD UPS (USB) working with the newhidups drivers on Gentoo Linux. The one that is currently available at many local Costco stores and online. In case others need to replicate, I've attempted to document my steps over here.

Hello! First time posting to this list. I recently purchased a Tripp-Lite OMNIPLUS1000LCD from Costco (USA). I have it attached via USB to a Dell computer with Ubuntu 8.04 server (all updates on it). I've gone through a lot of research on google and this list and can't figure out why my UPS will not connect using nut/usbhid-ups. My setup in ups.conf is: ------- [OMNI1000LCD]

Greetings, Any suggestions? I think I'm close but I can't quite get tripplite_usb to talk to my OMNI1000LCD. I'm new to NUT and couldn't find an answer using Google. With any luck, I've simply missed the obvious. The system I'm using, kaylee, is a debian stable system with some debian testing installed and a 2.6.15.4 kernel. I downloaded NUT 2.0.3 and built it from

On 07/06/2017 02:18 AM, Charles Lepple wrote: > On Jul 5, 2017, at 5:34 PM, Ambrogio Coletti <ambrojohn at gmail.com > <mailto:ambrojohn at gmail.com>> wrote: >> >> From section 4.23 of the Developer Guide: >> >> "There are a few USB UPS devices that are not HID devices. These >> devices typically implement some version of the manufacturer?s

Good afternoon, I am trying to communicate with a new Tripp-Lite UPS via usb and having little luck. After more than a week on this I've decided to ask for help. I am very inexperienced at posting information to message boards, so hopefully I'm doing this right. I assume this is the correct place to post this message. I will start with the equipment I have. I am using Debian Sarge

I'm working on a gentoo server with Nut 2.0.5-r1 and libusb-0.1.12. I originally tried the hidups driver which seemed to work, but produced a large amount of unhandled events. Then I tried the newhidups which told me my ups wasn't supported. When I try using tripplite_usb -u root -DDDD /proc/bus/usb/002/002 I get that there isn't a match. But when I try using tripplite_usb -DDDD

Hello, I have encountered problems trying to set up nut to work with APC BackUps Pro CS connected over USB to an AMD64 machine running Debian. While apcupsd works fine with that device, whenever I start upsd I get the following messages in syslog: hidups[23159]: Startup successful upsd[23160]: Connected to UPS [apc1]: hidups-hiddev0 upsd[23161]: Startup successful hidups[23159]: Unhandled event:

Hi, I'm new to nut, just installed it. I configured it using the hidups driver to work with my APC BackUPS: # upsc apc350@localhost battery.charge: 100 battery.runtime: 885 battery.voltage: 13.5 driver.name: hidups driver.parameter.port: /dev/usb/hiddev0 driver.version: 2.0.0 ups.delay.shutdown: -1 ups.delay.start: 0 ups.load: 660 ups.mfr: American Power Conversion ups.model: Back-UPS CS 350

Hi Charles and Jonathan, I am going through my over 300 unread NUT messages, and I just discovered this one from mid-December. At the time, I was trying to clean up the tripplite subdriver of newhidups, but never got the information I needed. I have enabled this driver now, but it is marked "experimental". The driver is still incomplete, in the sense that there are many unmapped device

Hi! I've got a Mandrake 2006.0 machine and a APC Back-UPS Pro 500/1000/1500 (from lsusb). The Mandrake package version of nut is 2.0.1 and hidups actually detects the UPS, however I get loads of these: Sep 12 18:26:11 vader hidups[7658]: Ignoring x86 page event 0xff860080 (0) Sep 12 18:26:11 vader hidups[7658]: Unhandled event: 0x840058 (6) Sep 12 18:26:11 vader hidups[7658]: Unhandled

I'd like to submit a patch to the 'hidups' driver. I'm a bit new to open-source development model, so I hope I'm not committing a faux paus by just posting it here. I did verify that the problem still exists (by source code inspection) in the latest dev snapshot, which is nut-2.0.3-pre2. I'm using nut-2.0.2 myself. The problem is when I'm connecting to my APC

I just installed NUT and my UPS is an APC Back-UPS ES 500. I looked in the list of drivers and found APC Back-UPS ES 350 listed in "drivers.txt" -- that list said I should use either the newhidups or hidups driver. I looked in the installation and I found headers and c files to create these drivers (I think), but in /usr/local/ups/bin there is no driver named, "newhidups or

I Seem to have made some progress in getting nut-2.0.5 installed, but hidups still has a version number of 0.13. First is hidups 0.13 the correct version? if not how do I find the correct version. Second if my Geek Squad GS1285U UPS is not supported how do I proceed. I have been a programmer for 35 years(mostly high level computer aided design), written code in 20 some languages, am retired

2006/1/13, Paul Mogren <fkamogee@yahoo.com>: > > This thread is FYI. I don't need any help here. > no, but some details for those who will read it, maybe ;-) I have SUSE 10.0 and an MGE Ellipse. I installed the NUT package from MGE. > > 1) The generated ups.conf pointed to a bad location: > /dev//dev/input/event0 > who generated that ? it seems like an old hiddev

is there a way to override the productid (like -x productid=1234) when using newhidups? just thought i'd try it with the F6C1500-TW-RK over usb. i was able to get hidups to work using the below settings, but it provides limited information. my ups.conf entry: [belkin] driver = hidups port = /dev/usb/hiddev0 and the output of upsc: gateway:/etc/nut# upsc

I am forwarding the below message. Does anybody on this list know anything about this problem? Petr - perhaps you should switch from the "hidups" to the "newhidups" driver. I believe it supported the APC Back UPS even in NUT 2.0.2, and it certainly does so in the Development version that you can get from CVS (see the NUT download page). Also, could you post the output of