similar to: Nexenta: "load_mib2nut: using pw mib" package / config / or firewall problem?

Updating an old thread. History here. http://lists.alioth.debian.org/pipermail/nut-upsdev/2013-January/006391.html http://lists.alioth.debian.org/pipermail/nut-upsdev/2013-February/006394.html http://lists.alioth.debian.org/pipermail/nut-upsdev/2013-February/006398.html On Fri, 1 Feb 2013, Tim Rice wrote: [snip] > > In all my testing I discovered the APC AP9630 is kind of flaky when >

nut-2.6.5 Scientific Linux 6.3 APC AP9630 management card My basic question is, does nut's SNMPv3 implementation work? I have this in /etc/ups/ups.conf ...... [tfapc01] driver = snmp-ups port = tfapc01.testfest.ixorg.org mibs = apcc snmp_version = v3 secLevel = authPriv secName = tfsnmpprof1 authPassword = ralow6moHet7zoboP8 privPassword = tuseL8Pakaz9degim7 authProtocol=MD5

Hi, Nut-upsusers, I am having problem configuring NUT to work with Tripplite UPS through SNMP. There is a Tripplite SmartOnline SU10KRT3/1X and attempts to monitor it using NUT though SNMP are failing... OS: Enterprise Linux 6, Nut version: 2.6.5. ups.conf is configured: [trippliteups] driver = snmp-ups port = 10.200.254.39 desc = "ProductionServer"

I did a bunch of work on this today. It should be all set to go. This patch is to add support for the Cyberpower RMCARD snmp cards. I basically copied the driver for bestpower, changed the name and updated the mib map. I have this running on two separate systems (two separate ups's) and it looks good. The only thing I could not figure out was updating the Makefile.am (my aclocal/libtools

Hello We have an Socomec Sicon Netys PR3000 UPS equipped with NetVision Web/SNMP adaptor. I try to monitor the ups using snmp-ups driver and netvision mibs set. The snmp-ups driver starts correctly and connects to the UPS, upsd confirms it, but upsmon constantly shows "No communication" error I think the cause is the SNMP adapter reports the UPS status as "ECO mode"

Hello, I''ve been using Nexentastore Community Edition with no issues now for a while now, however last week I was going to rebuild a different system so I started to copy all the data off that to my to a raidz2 volume on me CE system. This was going fine until I noticed that they copy was stalled, as well as the entire system was non-responsive. I let it sit for several hours with no

Hi, just testing with a HP R1500 XR (answers as Powerware) with SNMP/Serial Port Card using SNMP I found: 1st: The batt status 1.3.6.1.4.1.534.1.2.5.0 goes away after some time. Isn't visible in a snmpwalk anymore, seems to be a bug in the card. 2nd: The ups turns into "resting" 48h after battery is full. It turns off the fan, the batt voltage lowers a little, it seems, avoiding

Thanks, now I started getting messages from the list. As you advised, I renamed the mib file NETCARD.mib to Tripplite and ran command ./gen-snmp-subdriver.sh -H 10.200.254.39 -c public -n Tripplite Here is what it says: snmp_build: unknown failuresnmpget: Error building ASN.1 representation (Can't build OID for variable) COUNT = 0 / 0 Creating tripplite-mib.h Creating tripplite-mib.c Done.

[Please keep the list CC'd. Thanks!] On Feb 13, 2014, at 4:55 AM, ??? ????? wrote: > Can you try adding "-v 1" to the snmpwalk command? If that works, we can add it to gen-snmp-subdriver.sh. > > Yes, I tried it before, ran command "snmpwalk -v 1 -On -c public 10.200.254.39 .1.3.6.1.4.1.935" > > Output: > .1.3.6.1.4.1.935 = NULL > Error: OID not

Sorry for an off-topic question, but anyone knows how to make network configuration (done with ifconfig/route add) sticky in nexenta core/napp-it? After reboot system reverts to 0.0.0.0 and doesn''t listen to /etc/defaultrouter Thanks.

Does anyone know of a prebuilt Solaris or Nexenta DomU with a ZFS root that uses paravirtualization? I''ve been mulling over the directions for both, but my Xen DomU is Fedora for the moment. (I hope to use OpenSolaris as my Dom0 at some point, but due to lack of hardware and time, I need to build the VMs first before I format my home-server.) Thanks, -Luke

Hi, I''ve migrated my tc configuration from CBQ to HTB. One problem appeared. Htb seems to miscalculate the bandwidth for classes with greater rates. For rates below 2Mbit there is almost no difference between the configured and the measured rate. For large ones the problem starts. My root class has 10Mbit rate and when the interface has heavy trafic the measured bandwidth

On 02.10.2014 03:42, Charles Lepple wrote: > On Oct 1, 2014, at 5:07 AM, Tarvo.Tiits at automaatika.ee wrote: > >> Why is ups.status empty? > If I understand the commit log for SVN r3590, then that revision was supposed to set the status to OL if the numeric state was 9 for ECO mode. It does not appear to do that: > >

I have a Cisco 6509 switch that I'm monitoring with SNMP from a CentOS5 machine. SNMP polls are the only access I have to this device, we are not allowed to log on via telnet. How can I find out which port on the switch a particular server is connected to? I was hoping that this is somehow possible using the mac address and the data gathered from snmpwalk/snmpget requests but I'm not

Hi all, Not sure if this is on topic or not. I'm trying to query an SNMP value from centos 6 and I get a bad response if I don't specify the MIB to use: 0 digimer at pulsar:~/anvil/striker$ snmpget -v2c -c public -m /home/digimer/Downloads/APC/AP7900/MIB/powernet421.mib 10.255.2.1 .1.3.6.1.2.1.2.2.1.6.2 RFC1213-MIB::ifPhysAddress.2 = Hex-STRING: 00 C0 B7 5F 8A 85 0 digimer at

OpenBSD 5.6 nut-2.7.2 (bin package) Liebert IntelliSlot Unity Card IS-UNITY-DP ups.conf: ...... ? mibs = ietf ? snmp_version = v1 ...... The problem is that the card responds to other snmp (v1,2c,3) requests normally but not to the 1.3.6.1.2.1.33.1.1.1.0 (UPS-MIB.upsIdentManufacturer). # snmp-ups -a laes2ups -DDDDDDD Network UPS Tools - Generic SNMP UPS driver 0.72 (2.7.2) ?? 0.000000???? debug

Greetings all, I''ve been searching high and low for any inkling of how people are monitoring classes for long term usage data. I''m thinking something along a script to collect the data for mrtg or perhaps even an snmp module that would present them as interfaces to be polled....has anyone done any work in this area? John Dunning Assistant Director Net & Tech Svcs Wayne

I check system load like so: [root at server cron.daily]# w 10:07:33 up 4 days, 15:01, 2 users, load average: 4.22, 3.17, 3.09 I would like to to graph the 3.17 5 minute average with MRTG. Anyone know of some examples of doing this?

Hello, i'm trying to monitor a APC Smart-UPS 1000 behind a APC AP9630 Network Management Card via SNMPv3 using the AES Privacy Protocol. * OS name and version: Debian 10.1 * exact NUT version: 2.7.4 * NUT installation method: from debian package 2.7.4-8 * exact device name and related information * Model Number AP9630 * Hardware Revision 08 * Manufacture Date

> Does it have the same behavior if you start from .1.3.6.1.4.1.935*.1* or . > 1.3.6.1.4.1.935.1.1? If not, no worries - see below. > > Yes, says "Timeout: No Response from 10.200.254.39", Ok. > ..... > > >> The important part of "mode 2" is to have the output of snmpwalk. It is >> possible to query each OID, and manually build the *-mib.c