similar to: UPS Liebert GXT3 config

Hello, I (now) own an Emerson Liebert GXT3 6000VA conected via USB. I've searched the web trying to configure nut (nut-2.6.5-1.el6.x86_64 epel rpm on CentOS 6.3) to monitor the UPS, but couldn't find a successful configuration. I'm running kernel 2.6.32-279.14.1.el6.x86_64. The UPS is connected with an USB cable: Bus 004 Device 002: ID 10af:0008 Liebert Corp. PowerSure Interactive

Hello everyone, Charles suggested (about a week ago) that I repost to this list. I took a moment to run some additional tests ... The basics: -- UPS: Liebert PowerSure PSA 500 (from the 230 VAC / 50 Hz line) -- Kernel: 2.6.11.5 (from sources), USB support (down to and including CONFIG_USB_HIDDEV) compiled in statically (not as a module) -- Rest of OS: Basically still from the original SuSE

This patch adds support for the following ups to liebert-hid.c: $ lsusb | grep Liebert Bus 007 Device 005: ID 10af:0001 Liebert Corp. PowerSure PSA UPS Using this patch, I'm able to obtain information about the ups via upsc: $ upsc upsname battery.charge: 100 battery.runtime: 1012 battery.type: PbAc battery.voltage: 1172 battery.voltage.nominal: 12 driver.name: usbhid-ups

Hello. I have Liebert GXT3 UPS connected to CentOS Linux with kernel 2.6.32-131.0.15.el6.x86_64 and nut version 2.6.5-2. lsusb: Bus 002 Device 003: ID 10af:0000 Liebert Corp. UPS And this UPS detected only with this section in ups.conf: [liebert] driver = liebert port = /dev/ttyS0 but only this variables available: device.mfr: Liebert device.model: MultiLink device.type: ups

On Aug 19, 2013, at 12:58 PM, Korviakov Andrey wrote: > I have Liebert GXT3 UPS connected to CentOS Linux with kernel 2.6.32-131.0.15.el6.x86_64 and nut version 2.6.5-2. > lsusb: Bus 002 Device 003: ID 10af:0000 Liebert Corp. UPS > > And this UPS detected only with this section in ups.conf: > > [liebert] > driver = liebert > port = /dev/ttyS0 I am confused.

Following the instructions a following site I can not get nut to work with my UPS. http://bernaerts.dyndns.org/linux/75-debian/335-debian-wheezy-install-monitor-eaton-ups Hope that you can find out what is wrong by the provided info in the email Best Regards, Magnus Karlsson # lsusb -s 001:005 -v Bus 001 Device 005: ID 06da:0002 Phoenixtec Power Co., Ltd UPS Device Descriptor: bLength

On Oct 29, 2014, at 5:08 PM, Marcelo Fernandez <marcelo.fidel.fernandez at gmail.com> wrote: > Hi, > > I've bought a Liebert GXT3 UPS and I'm trying to use it with nut. I'm > using Ubuntu 14.04, but I'm having troubles (similar to this thread > [1]) using the standard "nut" package from the Ubuntu repositories. > > After some more searching,

Replaced ups with a new Liebert UPS and it seems the device may not be known to nut. Below is output of lsusb: ID 10af:0002 Liebert Corp. PowerSure PST UPS Sent from Outlook<http://aka.ms/weboutlook> -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://alioth-lists.debian.net/pipermail/nut-upsuser/attachments/20231204/7c08a727/attachment.htm>

Hi, I've bought a Liebert GXT3 UPS and I'm trying to use it with nut. I'm using Ubuntu 14.04, but I'm having troubles (similar to this thread [1]) using the standard "nut" package from the Ubuntu repositories. After some more searching, I've found this very recent thread in this list ("Return on experience with an Emerson/Liebert GXT3" [2]), and from my

Hi, I'm new in the list and I'm having a little bit trouble to put the megatec_usb to work. I've been using NUT for a while with the apc and megatec driver (serial), with no problem. The server is a Ubuntu 8.04.2 with NUT version 2.2.1-2.1ubuntu7.2, the default package version in this ubuntu release. I've configured the ups.conf as follows: [sms] driver = megatec_usb

Hi, I'm new in the list and I'm having a little bit trouble to put the megatec_usb to work. I've been using NUT for a while with the apc and megatec driver (serial), with no problem. The server is a Ubuntu 8.04.2 with NUT version 2.2.1-2.1ubuntu7.2, the default package version in this ubuntu release. I've configured the ups.conf as follows: [sms] driver = megatec_usb

Ok guys I get this errors: Network UPS Tools ? UPS driver controller 2.4.1 Network UPS Tools ? Generic HID driver 0.34 (2.4.1) USB communication driver 0.31 No matching HID UPS found my ups.conf is: [ap1000] driver = usbhid-ups port = auto I?ve also tried to set a specific usb port and change driver. My ups is a AMACROX 1000 http://www.amacrox.com//english/01_product/02_01detail.aspx?pdid=46

Bonjour, Je souheterais utilis? la version qui permet le '-x generic',mais je ne sais pas ou la recuperer car ca devrait solutionner mon probleme (cf mail ci-dessous) DaneZ _____ From: DaneZ [mailto:david.guillotte@danez.no-ip.org] To: arnaud.quette@mgeups.com Sent: Sat, 08 Jul 2006 23:24:06 +0200 Subject: Fw: INFOSEC 500 XP en USB _____ Bonjour Arnaud, Je me

Hi. I would like to share with you my experience on trying to use nut with a Liebert GXT3 on a Debian wheezy with nut-server 2.6.4. Please find my observations below. (1) I've installed the packaged version of nut-server # aptitude install nut-server (2) I did some tuning for my configuration #??cat << EOF >> /etc/nut/ups.conf user=nut [liebert] ??????? driver=usbhid-ups

2014-11-09 9:59 GMT-03:00 Charles Lepple <clepple at gmail.com>: > On Nov 9, 2014, at 6:58 AM, Marcelo Fernandez <marcelo.fidel.fernandez at gmail.com> wrote: > >> I'm attaching a new debug log with this modification, just in case, >> but I'm still seeing the lines you've pointed at: >> >> 0.062308 Path: UPS.PowerSummary.Voltage, Type:

2014-11-07 0:16 GMT-03:00 Charles Lepple <clepple at gmail.com>: > On Nov 6, 2014, at 5:56 PM, Marcelo Fernandez <marcelo.fidel.fernandez at gmail.com> wrote: > >> battery.voltage: 10000000. >> battery.voltage.nominal: 0.0 > > Well, these are certainly interesting values ;-) > > I suspect the correction for earlier units has failed. Can you please start

I looked through the faq, but couldn't find an answer to this. I'm trying to configure nut-2.0.4-26 on SuSE linux 10.2. In ups.conf, I have [myups] driver = belkinunv port = /dev/undefined desc = "Local UPS" I'm trying to find out what the port should be set to. lsusb shows: Bus 001 Device 005: ID 050d:0980 Belkin Components Device Descriptor: bLength

Hi Arjen My apologies fro drifting off topic in the other mailing list...:-) On the bottom of the Belkin UPS unit - is the model number: F6C120auUNV The "au" is for Australia I think. "man belkinunv" states that F6C120-UNV is supported - and I assumed that the "au" would not prevent this. I plugged in the USB to gather the information you requested. My intention

[please keep the list CC'd.] On Aug 20, 2013, at 12:50 AM, Korviakov Andrey wrote: > Yes, it's my mistake: UPS used USB cable for communication, but i think that it's simple usb-com cable because nut work with liebert driver on ttyS0 port. If that is the case, I doubt that usbhid-ups will be able to retrieve any additional information. > In ups.conf i tried: > >

Hello, we have a Emerson Liebert GXT4, that we like to connect to our servers to shut them down if there is a power failure (which happens quite often in our area). I couldn't get the GXT4 working with usbhid-ups driver. So I need some advise to continue to get this device working. The GXT3 seems to be working ok with NUT (http://networkupstools.org/ddl/Liebert/GXT3.html). Here is my