similar to: CyberPower PR2200E

I did a bunch of work on this today. It should be all set to go. This patch is to add support for the Cyberpower RMCARD snmp cards. I basically copied the driver for bestpower, changed the name and updated the mib map. I have this running on two separate systems (two separate ups's) and it looks good. The only thing I could not figure out was updating the Makefile.am (my aclocal/libtools

I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower

I am using nut 2.2.2 and I have a CyberPower CP550SL. According to the drivers list, I should be using genericups with upstype set to 7, but when I try that and when I run upsc I get: driver.name: genericups driver.parameter.LB: 04 driver.parameter.pollinterval: 2 driver.parameter.port: /dev/ups driver.parameter.upstype: 7 driver.version: 2.2.2 driver.version.internal: 1.34 ups.mfr: CyberPower

The Hardware Compatibility List page on our website said to report any omissions in the list to this address. I bought a CyberPower UPS Model *LX1500GU*. It looks similar to the *CP1500AVRLCD*. My intention is to configure it in FreeNAS (FreeBSD). The FreeNAS user guide says it uses NUT to provide UPS support an contains a link to your website for a list of drivers of supported UPS devices. I

All, I just had a power failure that caused me a little drama. This spurred me into trying to get NUT up on my cyberpower 1500 again. For about 6 months I tried to get it to work with the new power panel drive with no luck. Today I removed all the old files for NUT and installed the newest version I could find (2.4.3) and it works perfectly now with my UPS. Hopefully now I

Just noticed that our new server has a newer 80+ efficiency 865W PSU with PFC. So apparenty our existing 1500VA (865W) APC Back-UPS is not safe to use anymore. We apparently need a pure sine wave UPS. http://nam-en.apc.com/app/answers/detail/a_id/8883 I found an affordable 1500VA UPS by CyberPower, model CP1500PFCLCD, which has a pure sine wave output. Wondering if anyone has experience with

Trying to configure multiple UPS on one Raspberry Pi 4 (Bullseye). Issue: Whenever more than one is plugged in, one shows as all - as in "upsc x" for all of them shows identical information for one UPS rather distinct for each plugged in. OS: /proc/version = "Linux version 5.10.103-v7l+ (dom at buildbot) (arm-linux-gnueabihf-gcc-8 (Ubuntu/Linaro 8.4.0-3ubuntu1) 8.4.0, GNU ld (GNU

Is anyone working on anything to support the Cyberpower CP550SL/AE550 Serial? Any idea if it uses the same or similar protocol as the other Cyberpower models? I have an HP 4952A Serial Protocol Analyzer and a Cyberpower CP550SL. Once I get the CP550SL up and working in Windows over RS232 I'll hook up the 4952A and see whats going on. I'm not sure what it uses for default baud rate.

Hello, I'm a new to NUT and I'm having some setup problems. Here's my setup: Nut 2.0.2 Gentoo Linux 2.6.13-r3 CyberPower AVR900 According to the hardware compatibility guide this setup should work. Here's what I get: root@gentoo (0) [552] % upsdrvctl start Network UPS Tools - UPS driver controller 2.0.2 Network UPS Tools - CyberPower driver 1.00 (2.0.2)

Hi, guys. I have a new CyberPower PR2200 which I'm trying to control using NUT. It has a serial port and I'm connected serially. I am using the cyberpower driver and before a power failure it seems to mostly be working: jeff@backup:~$ upsc cyberpower@localhost battery.charge: 000 driver.name: cyberpower driver.parameter.port: /dev/ttyS0 driver.version: 2.0.4 driver.version.internal: 1.00

Hello, I'm looking for a UPS that the beeper can be silenced with nut via ups.beeper.status variable for a HTPC close to bedrooms. I have googled extensively and there is not a lot of information about which UPS's actually support this feature. There are few references to UPS's that apparently list ups.beeper.status as being available, but without actually being

Arjen, I read the following in the upgrade notes and just wanted to see what the status was for the cyberpower driver? The note reads: - The cpsups and nitram drivers have been replaced by the powerpanel driver, and removed from the tree. The cyberpower driver may suffer the same in the future. What does this mean to me -- a cyberpower user? -- David C. Rankin, J.D.,P.E. Rankin Law

I recently purchased a CyberPower CP1200AVR UPS and am trying to get NUT 2.0.3 or NUT 2.1.0 to work with the newhidups driver, but am having little success. Before I purchased I did some googling and saw people talking about problems so I'm guessing it may not be supported yet? I did find some posts about people getting it to (sort of) work with some hacks, but couldn't tell if they

Hello! I got my hands on a CyberPower 1500AVRT, and i'm trying to get it connected to my Gentoo machine. I've followed all the basic guides on setting up NUT and UPS' but have had no luck. My current ups.conf is: [cyberpower-gentoo] driver = cyberpower port = /dev/ttyS0 desc = Workstation Upon running /etc/init.d/upsd start or upsdrv start I get: * Starting

I am having some problems getting NUT to run with my cyberpower avr1200 (brandnew). I have a straight through serial cable, and I am getting this: /usr/local/etc/rc.d/nut.sh start Starting nut. Network UPS Tools - UPS driver controller 2.0.2 Network UPS Tools - CyberPower driver 1.00 (2.0.2) Giving up on hardware detection after 3 tries Unable to get initial hardware info string Driver failed

I am having some problems getting NUT to run with my cyberpower avr1200 (brandnew). I have a straight through serial cable, and I am getting this: /usr/local/etc/rc.d/nut.sh start Starting nut. Network UPS Tools - UPS driver controller 2.0.2 Network UPS Tools - CyberPower driver 1.00 (2.0.2) Giving up on hardware detection after 3 tries Unable to get initial hardware info string Driver failed

Anyone familiar with Cyberpower's model numbers? I finally got sick of my Tripplite's USB port going south, all the time, so I'm looking to replace it. The HCL has an entry for a Cyberpower model CP1500AVRLCD. Not listed is the CP1500PFCLCD model, a newer, premium version of the unit; but the HCL does have an entry for the CP1000PFCLCD model. Pretty sure that the CP1500PFCLCD

This unit works fine with the "cyberpower" driver (which reports it as "Unknown model - 15"). It reads this much from it: battery.charge : 100 driver.name : cyberpower driver.parameter.pollinterval : 2 driver.parameter.port : /dev/ttyS0 driver.version : 2.2.0- driver.version.internal : 1.00 input.frequency : 60.2 input.voltage : 121 ups.firmware : 5.100

Hola Estic fora de l?oficina des de Dimecres 1 d'Agost fins el proper Dilluns 12 d'Agost, Tan aviat sigui possible li contestar? el seu correu. En cas de ser un tema urgent, preguem reenvi? aquest mateix correu a l?adre?a d?email sst at salicru.com, els meus companys li donaran resposta el mes aviat possible, gr?cies. Hola Me encuentro fuera de la oficina del Miercoles 1 de Agosto

root at Monitor:/etc/nut# upsc ups1 Init SSL without certificate database battery.runtime: 133200.00 battery.runtime.elapsed: 0.00 device.mfr: CYBERPOWER device.model: PR2200LCDRT2U device.serial: 1 device.type: ups driver.name: snmp-ups driver.parameter.pollfreq: 1 driver.parameter.pollinterval: 2 driver.parameter.port: 192.168.1.7 driver.parameter.snmp_version: v1 driver.version: