similar to: Old fashion UPS monitoring

I tried to find a search button for the mailing list but could not. So rtfm me with the link please. If not.. I have an old Deltec PowerRite Pro 2 UPS which has a 9 pin serial cable. By trial and error Im pretty sure I found LB = DCD, but can not get the combination for OB / OL. No matter what I do I get the results below. driver.name: genericups driver.parameter.CP: CTS driver.parameter.LB:

> +22 = Gamatronic UPSs with alarm interface > + [CP=RTS] [OL=CTS] [LB=\-DCD] [SD=DTR] > + > +22 = CyberPower SL seriess > + [CP=RTS] [OL=CTS] [LB=\-CAR] [SD=DTR] > + > + This part of the patch is no good. While TIOCM_CAR is equivalent to TIOCM_CD (at least in some implementations) CAR certainly isn't handled the same as DCD by genericups. It won't be

Hello, I have a UPS connected to my server with the following: Server is Suse 10.1 Nut version is?Network UPS Tools - Generic UPS driver 1.32 (2.0.4) I installed this around 2005 and cannot remember how I installed the software. ups.conf: [sdrups] driver = genericups port = /dev/ttyS0 desc = "For Server & Backup" upstype = 9 upsd.conf: ACL all 0.0.0.0/0 ACL localhost

Hello, I have one UPS Infosec XP Pro 2500 RM and it works with windows sw RUPS2000. Now I want to install this UPS as virtual server on vmware ESXi vMA - (SUSE SLES 11SP2 linux). On this linux I have NUT 2.6.0 and I stopped now with configuration of genericups driver. Working cable (direct cable pin1-pin1 ... pin9-pin9) connection on Windows: PIN | PC | UPS

Hello, I got this information from the manufacturer of my ups Kobian/Mercury and were tested wtih powstatd on Linux (Works OK). Now i want to configure it with NUT and i didn't have any luck (it always says OB) Initiliasation for monitoring: RTS = 1 (High) Main power fail: CTS = 0 (Low) Batter low: DCD = 0 (Low) Kill UPS: DTR = 0 (Low) How would the ups.conf look like? Reagards, Lep

>> On Nov 21, 2015, at 2:43 AM, R?bert SZAKSZ <robert at szaksz.eu> wrote: >> >> I mesured it and on DC and it shows 0 V (zero V). >> May be the information (pls. see attachment) that UPS PIN1 should bee keept HI is mandatory. Should I connect it to PC PIN4 DTR? > >Certainly possible. blazer_ser and nutdrv_qx should set DTR high and RTS low by default, but

Hi there. At the moment I'm trying to get my HP T1500 XR (Powerware 5125) UPS to work with NUT. NUT registers that the UPS is on battery/online, but I just cant get the program to shut down the computer I'm using the original cable (thus I didn't enter anything in the ups.conf file) If I remove the cable and run the daemon/program the computer will shutdown after x minutes defined in

It there a way to get the genericups driver to set a output on the serial port? On the APC BackupPro the will pull the BattLow line low with a pull down resistor it's up to you to from the PC side to pull the line high with a pullup resistor from one of the RS232 output pins. Then monitor the line with another pin. Regards Rabie -------------- next part -------------- An HTML attachment was

Hello, ahgu >I have a unisys UPS, I probed the RS232 and notice that pin 2, >(receive data) is going from -6v (OL) to 12v(OB), but I don't see the >setting for the genericups. Seems nobody else is using the RD pin? >Any driver I can use? >Thanks >-Andrew Try RX as signal name (not RD). -- Best regards, Sergiy mailto:rendol@mail.zp.ua

Hello, as I have read manual, if I use in file authorized_keys option command="" with some command, no other commands will be permitted. I have tried it, created authorized_keys2 for root and added there command="rdiff-backup --server" and after that tried to login. Thit command was executed, but I was normally able to supply other comand as root. Can you tell me why? Thank

Hey all, I found a pinout of powercom's Kingpro UPSes in their manual. http://www.powercom-ups.com/manuals/kingpro.pdf Page 11. Unfortunately, this doesn't give PROTOCOL details. Does anyone have a "first step" at how to decode that? (for example, how to gauge line speed, how to "snoop" the serial port under windows? (for which the only software exists right

There should be a line-table entry for the end of the function, which appears to be missing from the dump you provided. llvm-dwarfdump should report this address with 'end_sequence' in the Flags. Are you using a different dumper? I am not sure but my guess would be that inline data is not represented in the line table. The line table's primary purpose is to inform the debugger

Hello. Has anyone been able to successfully make data (dialup modem) calls through a TDM2400E? We're able to make fax and credit card calls fine, but cannot successfully make modem calls using a 56K modem connected to a patch panel connected to an FXS port which then gets bridged to an FXO port connected directly to a phone line. We have 'echocancelwhenbridged=no' set in

Dear NUT developers, I am using NUT + bcmxcp + Powerware 9315. I would like to use NUT to shut down my systems if the air conditioning fails and the room get too hot. I want the same shutdown sequence as would be produced when the UPS goes on battery. The UPS has a terminal block at the front for up to six different 'building alarms'. I can connect a thermostat (35C) to the

I'm not familiar with the target instruction set, but if "MOV PC, R0" is not a return instruction, I'm guessing that the sequence starting at A39C is a dispatch through a jump table. The jump table would be considered part of the instruction stream and included in the scope of the line table. This is not a case where you would see end_sequence; my mistake. The line table does

On Tue, 31 Jan 2006, Arjen de Korte wrote: > > But I'd like to know what I'm testing. Could you please post a bug tracker > > URL? I'm having trouble finding #302338. > > That may be because I closed the bug (maybe a little overenthousiastic). See > > http://alioth.debian.org/tracker/index.php?func=detail&aid=302338&group_id=30602&atid=411542 >

Debian sid package v. 2.6.4-2.3 UPS nitram elite 2002 700VA (serial port) MOBO A7V8X-X ================================ Hi list, Everything work fine, except after an AC supply shortage: the UPS don't come back to a normal behavior, it stays on battery (of course, it works right w/o any cable). Is there something I can do recover a normal behavior? JY -- Too much of a good thing is

Hi Mario, Mario Cassani wrote: > Hallo Arnaud, > some months ago I bought an SBS GC400 UPS. > I came with a kit RS232 + UPSmart CDROM that works only with RedHat 7.0-7.3. > As I use Debian I tried alien with no success. > > Can you please provide me with any hint to understand if my UPS can be managed by NUT? > Can a driver be written, knowing how the cable

Hello everyone, If anyone is interested, I have created a HOWTO on running a Motorola GPS receiver connected to a CentOS 7 box via serial port (com1), with 1PPS over DCD. The trick here is that CentOS 7 uses systemd and setup was a bit different. Anyway, everything works. The result is a highly accurate NTP server, Stratum 1. Here is the documentation.

Hello again, I have a Sola 305 (aka Powerware 3110) here connected via a serial INT-0051 cable which I am trying to get working with nut. The driver.list file indicates that nut supports the Sola 305 when connected via the INT-0025C cable using the genericups driver with upstype set to 7 but it does not mention the INT-0051. I was able to use the "Basic CheckUPS II" utility provided