similar to: two MGE Ellipse 1500 ups via usb

Hi, I didn't found an answer for my question in NUT documentation/FAQ or this mailing list archive so I?m posting it here. I want to start a timer only if both of my UPSes remain on battery. Not just one, both. My UPSes are: - ups1@host-a - ups2@host-b Is it possible to use something like this in upssched.conf? AT ONBATT ups1.* && ups2.* START-TIMER onbattwarn 180 Thanks,

Hello, I've got a setup with NUT, where we've got two UPSes, ups1 and ups2. UPS1 supports our servers, while UPS2 supports our desktop boxes. We monitor both of them via USB on a box now called "upsmon". The interesting point comes here. We monitor both UPSes on the upsmon box, but if UPS2 fails, which supports our desktop boxes, NUT shouldn't initiate a shutdown in

New NUT install dealing with three APC Smart-UPS 5000s, two of which have AP9617 and the third has a AP9619 card. The SNMPv3 configurations on all three are exactly the same. This is confirmed by snmpget calls that work just fine: snmpget -Cf -v3 -u [...] -l authPriv -A '[...]' -X '[...]' -a MD5 -x DES [upsname] .1.3.6.1.4.1.318.1.1.1.1.1.1.0 snmp-ups can query all three

Hello, We have two APC Back-UPS RS 1500 USB stuff, and i've got a bit of a problem with it and NUT. The usbdevs output: addr 2: Back-UPS RS 1500 FW:8.g8 .I USB FW:g8, American Power Conversion addr 3: Back-UPS RS 1500 FW:8.g8 .I USB FW:g8, American Power Conversion (UPS1 and UPS2) I've configured our NUT system to monitor the UPSes, and it went very fine till the time had arrived for a

Hi, I've got a question about managing two UPSes under NUT. I have two similar model APC usb-connected UPSes to work with, but don't know how to manage them simultaneously from under Windows. Long story short, my ups.conf looks like this: --- ups.conf --- [ups1] driver= usbhid-ups port= auto serial=AS1054340323 [ups2] driver= usbhid-ups port= auto serial=AS1026662626 ---

Dear List, The driver usbhid-ups does not detect my MGE Ellipse 1500. I'm running openSuSE Linux 10.3, kernel 2.6.22 with mgeups-psp-3.0.4-2, nut-2.2.0-20 installed from MGE's rpm's. (Merci MGE!) lsusb shows: Bus 001 Device 004: ID 0463:ffff MGE UPS Systems UPS /etc/ups/ups.conf says: [myups] driver = usbhid-ups port = auto desc = "Local UPS"

Hi, I have the above UPS connected to a FreeBSD 6.2 box and it shows 'data stale' very frequently (every few minutes). I have tried the usual trick of setting maxage, poll interval, etc etc but to no avail. When I wind up logging I see (on mge-shut) entering shut_get_report(id: 0d, len: 1800) shut_wait_ack(): ACK received entering shut_get_report(id: 16, len: 1800) shut_wait_ack():

Hello, I have Ellipse ASR 1500 UPS and now I'm trying to monutor it with NUT from FreeBSD. It seems that there are some problems with this UPS: =================================== ugen0: MGE UPS SYSTEMS ELLIPSE, rev 1.10/42.41, addr 2 > usbdevs -v Controller /dev/usb0: addr 1: full speed, self powered, config 1, OHCI root hub(0x0000), NEC(0x0000), rev 1.00 port 1 powered port 2

I'm trying to set up nut with a MGE UPS equiupped with a network management card, but encountered a problem. UPS: MGE Pulsar M 3000 Network Management card (installed in the UPS): 66102 (2006 edition) Operating system: FreeBSD Nut port version: 2.0.5 Nut driver: snmp-ups According to MGE in Norway this card is supported by nut, but only the old version of the card (66244) is listed on

Hi, I have had a long standing problem with NUT talking to 110V MGE UPSs on FreeBSD, I was recently investigating again and noticed that upsd seems overly noisy, eg.. May 5 03:50:36 egbert upsd[96662]: UPS [ups1] data is no longer stale May 5 03:50:36 egbert upsd[96662]: Data for UPS [ups1] is stale - check driver May 5 03:50:36 egbert upsd[96662]: UPS [ups1] data is no longer stale May 5

Hi Charles, Running upsdrvctl -D start on the host with all three configured to SNMPv3 kicks out 56 different "unhandled ASN 0x81 from ..." lines on all three but importantly they all start up and keep running. I'm starting to suspect the startup is taking so long that systemd is timing out and killing it. time -p reports real time of 133.27. I'm not a fan of systemd but

Hi All, I have an mge pulsar esv 14+ rackmount UPS connected via straight through serial cable to a USB to serial adaptor (My motherboard does not have a native RS232 port). I am running Ubuntu Server 9.04 x64, and nut 2.4.1-2ubuntu4 installed via APT. I am getting the error: Poll UPS [ups1 at localhost] failed - Driver not connected My conf files: (ups.conf) [ups1] driver=mge-utalk

Hi, I bought an Ellipse MAX 1100 a few months ago. First I attached it to my desktop and installed mge's personal solution pac. (a graphical interface which uses nut). It works. But I want to attach the ups to my server which runs without an x-server. I followed http://opensource.mgeups.com/install/debian.htm. Didn't work. Then I copied over the configuration files which the personal

I can't find a way to configure bcmxcp_usb to communicate with 2 UPS units. Maybe more simply, I can't find a way to tell the driver to only talk to one of the units on the bus. That is, I cannot find that the driver configuration file supports "serial =" or "bus = " or other such discriminators that other drivers do (usb_apc, etc.). So, I can't assign one Eaton

I am running NUT 2.2.0 compiled from the FreeBSD ports tree. [inchoate 14:50] ~ >upsc ups1 at localhost battery.charge: 59 battery.charge.low: 20 battery.charge.restart: 0 battery.runtime: 6350 battery.type: PbAc battery.voltage: 43.0 driver.name: usbhid-ups driver.parameter.offdelay: 120 driver.parameter.ondelay: 13 driver.parameter.pollinterval: 2 driver.parameter.port: auto driver.version:

My UPS is a Eaton Ellipse 1000S (But its identified as MGE Ellipse 0463:ffff). I have been using the usb interface with the usbhid-ups driver, but I found that sometimes (too much times) the driver doesn't respond and NUT doesn't receive changes nor notifications from the UPS. The kernel lose the connections with USB device, in the kernel logs appears: Dec 30 11:24:12 rei kernel:

Hi, I keep getting the following messages (or similar) in my syslog: Nov 23 11:38:08 io kernel: [763936.921566] usb 3-2: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 5 ret -110 Nov 23 11:38:08 io kernel: [763936.972569] usb 3-2: usbfs: USBDEVFS_CONTROL failed cmd usbhid-ups rqt 161 rq 1 len 5 ret -75 Nov 23 11:38:08 io kernel: [763936.976568] usb 3-2: usbfs: USBDEVFS_CONTROL

[fwded to the list] Hi Fran?ois, > I didn't post this on the list as it seems a little bit more MGE > stuff than nut. Anyway feel free to post it if you consider it's > relevant. > > This is the trace you were asking for. The Ellipse 800 correctly shut > down in this test : > > This was running on a i386 recent hardware, the cpu load is under 5%, > 360MB out of

I've recently bought an MGE 650 that has both cables : USB and Serial. Since it's used on a server, I'd prefer not to load usb drivers just for nut. The problem is, either with newhidups or with mge-shut, the driver instantanly report that the communication with my MGE is lost, and shotly after that my ups is unavailable. It never show up again, and nut constantly says that the

I have an MGE Ellipse Premium 1200 that I connected to my server using its USB cable. Nut seems to be working fine. I've done a power down test and it worked and came back up when the UPS had power again. I'm using the newhidups driver and the USB cable. The problem I'm having is that if I boot with the cable connected newhidups says it can't find the UPS. If I unplug and plug in