similar to: New NUT user with HP R3000XR problem

This is not a NUT question per se ... or at least, I don't think it is. I just replaced the battery pack in my HP R3000XR; the new batteries were shipped with 90% charge, were at about 87% when they went in, and were up to 98% charge the next day. Last weekend, the server that runs NUT went down for no apparent reason, wiping out its boot blocks, corrupting its boot archive beyond

On the basis of continuing experience, one final piece of R3000XR battery pack advice: After swapping the R3000XR battery pack, power-cycle the UPS, wait until the battery pack is at least 50% charged, then disconnect the UPS from wall power for a minute or so before plugging it back in. Until I did this, my UPS would charge the battery pack fully, then let it slowly self-discharge. After

I posted earlier about a problem with a HP R3000XR that was showing abnormally low charge a couple of days after replacing the battery pack. For those with R3000XRs, the progblem seems to be: (1) while you CAN hot-swap the battery-pack on an R3000XR, the UPS automatically goes into bypass mode when you do so; (2) it doesn't necessarily come OUT of bypass mode after you install the

I seem to have NUT all working with my R3000XR, except for the CGIs. The webserver's all properly configured and upsstats.cgi *runs*, but doesn't yield any useful output - no values are displayed, every value is replaced by [error: Invalid argument]. Apache is not logging any resulting errors, and there doesn't seem to be a lot of useful documentation on the CGIs to troubleshoot

I'm just in the process of upgrading from nut-2.4.1 to 2.4.3 on a dual-Xeon box running Solaris 10 amd64 (i686-pc-solaris2.10). I configured as follows: ./configure --prefix=/opt/nut --with-gnu-ld --with-serial --without-usb --with-cgi --with-gd-includes=-I/usr/local/include --with-gd-libs="-L/usr/local/lib -R/usr/local/lib -lgd" --with-user=nut --with-group=nut

The scenario: I have two Samba servers on my network. One, running v3.0.37, is on my main server, a Solaris 10 x86 box. The other, just updated from 3.0.37 to 3.4.5 in the hope of solving this problem, is on my workstation, a Gentoo Linux box. The Linux Samba server shares only [homes]. The Solaris Samba server shares [homes] and four other shares. Unix UIDs are synchromized betwene the

Hi there, I am trying to come up with a solution to the current Samba authentication voes on the gateway server for our distributed file system. We currently use smbpasswd file on the gateway server for authentication, which is not a secure way and requires each user to be specifically added in. I do not have much experience with Samba, so I am still learning quite a bit as I jump from

Hi I`m trying to test my controller with rspec and always get an error. The error is in the render_to_string method call (without it test works fine). So could u please help me with that? users_controller.rb: def update @user.update_attributes!(params[:user]) redirect_to @user, :status => 202, :text => render_to_string(:partial => "users/show", :type =>

On Fri, Feb 04, 2011 at 12:26:08PM +1100, Damien Miller wrote: > OpenSSH 5.8 has just been released. It will be available from the > mirrors listed at http://www.openssh.com/ shortly. I seem to have found a bug in 5.8p1. I work remotely, and use three SSH tunnels, two of the form ssh -L port:host:destport -f -N -q -l remoteuser remotehost, and one of the form ssh -D port -f -C -q -N -l

# reboot Connection to 192.168.5.81 closed by remote host. Connection to 192.168.5.81 closed. ppo at admin:/tmp$ ssh root at 192.168.5.81 root at 192.168.5.81's password: Last login: Tue Jul 30 14:10:49 2013 from pc-ppo.kh.ektos OpenBSD 5.3 (GENERIC.MP) #58: Tue Mar 12 18:43:53 MDT 2013 # ps -aux | grep ups root 2254 0.0 0.0 324 700 p0 S+ 5:29PM 0:00.00 grep ups # ps -aux

Here is what I did: # cd /root/nut/ # nut here it's checkouted repository # ./configure --with-user=_ups --with-group=_ups # cd drivers/ # make riello_ser # chgrp bin riello_ser # cp riello_ser /usr/local/bin # here I copied builder driver to folder where nut-package will store their files/drivers # pkg_add nut-2.6.5p1 # ls -la /dev/tty00 crw-rw---- 1 _ups _ups 8, 0 Jul 30

Hi, I have an HP R5500XR and a Compaq R3000XR that I would like to use with nut. I searched the compatibility lists and the mail list archives but couldn't find anything. They both have 9 pin serial ports. Can anyone give me any information about them, and if they are supported by nut? Thanks, Denny Fox

another attempt: # upsd Network UPS Tools upsd 2.6.5 fopen /var/db/nut/upsd.pid: No such file or directory listening on 127.0.0.1 port 3493 listening on ::1 port 3493 Can't connect to UPS [senpro] (riello_ser-senpro): No such file or directory # ls -la /var/db/nut/ total 12 drwx------ 2 _ups wheel 512 Jul 30 10:22 . drwxr-xr-x 10 root wheel 512 Jul 29 16:41 .. -rw-r--r-- 1 _ups

Hi Sven, 2008/1/25, Sven Koch <haegar at sdinet.de>: > Package: nut > Version: 2.2.1-1 > Severity: normal > > I am using a Mustec PowerMust 1000 USB, connected with a USB cable to > the PC. > > With nut 2.2.0-2.1 everything works without problems - but since the > 2.2.1-1 update the "upsdrvctl start" from the init script just fails, > executing the

I finally got around to writing myself a NUT UPS monitoring tool. NUT's UPS monitoring CGI tools provide a detailed instantaneous view of the UPS's state at any moment, but provide no history. The attached tool, upswatch, uses Kiss Gabor's UPS::Nut module and Tobi Oetiker's rrdtool to provide a graphical history of the major UPS operating parameters via a web browser.

Hi All, I'm trying to communication with the HP r3000 XR UP using the latest stable build and I'm getting the following errors. Can anyone enlighten me with the errors below and what other course of action I can take. Thanks in advance. Paul. [root@WRRFtpServer etc]# /usr/local/ups/bin/upsdrvctl start Network UPS Tools - UPS driver controller 2.0.5 Network UPS Tools - BCMXCP UPS

hello everyone, I've been testing the NUT solution as opposed to the undocumented LanSafe application to control my Eaton UPS. I am on a Slackware 13.37 system with a 2.6.37.6 kernel. NUT version is 2.4.3 . I installed the tarball by compiling it directly on my system (as a slackbuild package). The UPS is an Eaton Powerware 9155, but I don't know how to obtain the manufacturing date. The

Thanks for you reply. I have installed asciidoc with "pkg_add asciidoc" And it returns something: # asciidoc fgh asciidoc: FAILED: input file /root/nut/fgh missing # which asciidoc /usr/local/bin/asciidoc Maybe there is any way to skip building man pages. This is not the such main thing as a new devices support. I also could built the driver that I need # make riello_ser but I don't

Hi Matthijs, > Arnaud. >After some trial and error, i found out that the HP R3000 XR ups's we have >can be used with Network Ups Tools. >This using the bcmxcp driver. > >Note that in the code of this driver (line 1420) , the Baudrate is fixed to >9600 baud. >to connect to a serial HP R3000 XR ups one needs to change this to 19200 >baud. > >ideally, this should

Hi, I''m having a weird issue and was wondering if anyone else had run into it. I recently upgraded from puppet 2.7 -> 3.0.1 After cleaning up some gems on my puppet master everything seemed to be working ok. I had originally used the EPEL repo''s to deploy puppet, but switched to the Puppet Labs repos so I could upgrade to 2.7 then 3. On RHEL5 only, I get a RSTRING_PTR