similar to: Advice Partner PRPC650 - no serial device

Hello everyone, has anyone ever tried to make this device work with Linux and NUT? This is what udevadm monitor says: UEVENT[1215983089.652345] add /devices/pci0000:00/0000:00:0f.2/usb1/1-1 (usb) UEVENT[1215983089.652427] add /class/usb_endpoint/usbdev1.4_ep00 (usb_endpoint) UEVENT[1215983089.657975] add /devices/pci0000:00/0000:00:0f.2/usb1/1-1/1-1:1.0 (usb) UDEV

Hello. I found out that the new Windows Vista requires too much for my notebook computer. Although my Thinkpad R32 is quite usable and pretty fast, Windows Vista requires 128MB of VRAM and so on. So, I am thinking about replacing the Windows with the Linux. However, there are three critical programs I need to use on the Linux. 1. Delrome Street Atlas 2006 with the Earthmate GPS 2. Finale -

I have had a lot of problems with my XP system recently so I would like to convert over to Linux (Ubuntu) and the use of Street Atlas 2006 is the only thing really standing in my way. I installed Wine 1.0 and installed Street Atlas using it. SA brings up the basic map programs but not everything works correctly yet. I have observed the following error messages so far:

will be used by Nut's powercom driver. I've failed to google anything about this UPS working with Linux. > > What does 'lsusb -d 0d9f:0002' say for this device? Bus 001 Device 002: ID 0d9f:0002 Powercom Co., Ltd The current progress is like this: With help from linux-hotplug guys (http://thread.gmane.org/gmane.linux.hotplug.devel/13551) I've managed to /dev/ttyUSB0 to

Hi I am trying to connect a reliance netconnect data card on my linux box ( cent os ) , i am able to the detect the device /dev/ttyUSB0 these are the following steps I did : Check your card is recognized by the kernel # cat /proc/bus/usb/devices ..... ..... T: Bus=07 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 11 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P:

Hi I have to use a windows application tu upload firmware to a controller. It uses the serial port. I use a MacBook with Tiger 10.4.8 I have installed a usb-serial converter. The device is /dev/tty.usbserial tilo-lutz:~/.wine/dosdevices tilolutz$ dir /dev/tty.usbserial crw-rw-rw- 1 root wheel 9, 8 Feb 24 17:31 /dev/tty.usbserial I was able to compile wine 0.9.31 with help of darwine.

Hi everybody, I am installing an Upsilon 2000 UPS via USB adapter on a RedHat 9 and I cant make that the device communicate correctly. Please any help will be welcome dmesg attached Thanks Gonzalo Red Hat 9.0 2.4.34.1 #dmesg usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb.c: new USB bus registered, assigned bus number 1 usb-uhci.c: $Revision: 1.275 $ time 15:28:15

Hi Charles! Thanks a lot for your response. Now I figure why the isbmex driver was not working. On the other hand I've tried to run the command suggested. But no success. I got this information when running the dmesg command after running the modprobe $ sudo modprobe ftdi_sio vendor=0x0483 product=0x0035 [35816.111760] usbcore: registered new interface driver usbserial [35816.111792]

Hi all, Currently, the "megatec" driver only supports UPSes which have a serial (RS232) interface. However, I'm under the impression that most of the models that speak the megatec protocol, and have an USB interface, just have a standard serial-to-USB converter inside. This being the case, there should be a "/dev/ttyUSBx" device which the megatec driver could use just as

Hi all, Currently, the "megatec" driver only supports UPSes which have a serial (RS232) interface. However, I'm under the impression that most of the models that speak the megatec protocol, and have an USB interface, just have a standard serial-to-USB converter inside. This being the case, there should be a "/dev/ttyUSBx" device which the megatec driver could use just as

doctordruidphd wrote: > I am trying to use software to program a scanner radio (BCD396t and UASD software). The software installs and seems to run properly, reading and writing database files. But I cannot connect to the scanner, through a USB-to-serial cable. > OS: ubuntu-8.10, kubuntu-8.10, debian/lenny (tried them all) > > lsusb identifies the cable as follows: > Bus 002 Device

Hi all again, I found this kernel panic past days, now using the unsuported kernel and comes out again the same error. This time on '2.6.9-22.0.1.106.unsupported' kernel See attached logs, Env is the same with the same box, Hope it helps. TIA. JJ Garcia -------- Original Message -------- Subject: Kernel panic in usbserial. Date: Thu, 15 Dec 2005 12:09:53 +0100 From: J.J.Garcia

I am trying to access my GPS using wine 0.9.24 0n Suse 10.2 and Cxoffice 6.0 Beta 3a . Cxoffice 5.03 does not work at all with my Suse 10.2 installation. The Magellan road mate tools work well enough in both cxoffce beta and wine, however wine seems to handle it better when importing POI ( Points of Interest) files. Overall I think the wine included with Suse 10.2 is doing a better job -

Hi, Sorry to re-post, but I'm still having hassles with ztdummy. I'm using kernel 2.6.11.4-21.7-smp and Asterisk 1.0.8 on SuSE 9.3 The first 3 makes (see below) for zaptel work out ok - but the ztdummy.ko (etc) files *are* created even though I haven't yet uncommented ztdummy in Makefile. If the ztdummy bits are compiled, why edit Makefile & run make again? modprobe ztdummy

I'm having a bad time getting 3 TE410P's and one TDM400 working in the same box. At some point during the install of second card, wcusb starts loading. I believe this is one of the TE410 Cards causing this as there is no usb enabled. Module Size Used by Not tainted audit 89880 2 (autoclean) usbserial 23420 0 (autoclean) (unused)

Hi I have been searching the wiki and mailing lists and I cant see where my config is incorrect. I have a Digium tdm11b (1 fxo + 1 fxs) this is the output of cat /etc/zaptel.conf # Autogenerated by /usr/local/sbin/genzaptelconf -- do not hand edit # Zaptel Configuration File # # This file is parsed by the Zaptel Configurator, ztcfg # # It must be in the module loading order # Span 1: WCTDM/0

[Let's keep replies on the list please] On Thu, Mar 29, 2018 at 02:16:31PM +0200, Claudio Sasso wrote: > Hi Richard, > > thanks for the suggestions; I think I have a more fundamental > problem here, as after I added yajl, it complained about hivex, then > about augeas. But for now I would be content with a working build, > and later address the underling root cause if any,

Hello, I have a strong suspicion that something is not working right on my el6 laptop. I have a usb 3g dongle that works fine on windows and ubuntu. It's one of those ZTE dual-personality devices (usb id 19d2:2000). When it's plugged in, it appears as usb storge device, then needs to be ejected, then it appears as usb modem with few serial ports. This is handled properly by udev on

please subscribe to the nut user mailing list ( http://lists.alioth.debian.org/mailman/listinfo/nut-upsuser) and post the output of "/path/to/usbhid-ups -DDDDD -a <your_ups_name_in_ups.conf>" cheers, Arnaud -- Linux / Unix Expert R&D - Eaton - http://www.eaton.com/mgeops Network UPS Tools (NUT) Project Leader - http://www.networkupstools.org/ Debian Developer -

Hi all, Running a Centos 4.2 default config in a P4 1.7 Mhz 512 MB Usb 1.1 (Acer Aspire 1400 XV Laptop) with a usb2serial interface plugged from the system boot, and using that line as console line for a remote device, i had the following kernel panic after few times performing the "reset" command in the gnome-terminal due font corruption, i had this kernel panic: Dec 14 23:58:10