similar to: Exide NetUPS SE (aka Powerware 5119 etc)

Someone might want to add this to the docs - cable list and compatibility list - took me way to long to find. I was trying to find information on my UPS and came up with the following names for the same UPS series. Powerware 5119 Exide name was NetUPS SE Deltec name was PowerRite Pro II (1000VA-3000VA) What I have: The Exide NETUPS SE model PRC2400a p/n 05144038-3904 OUTPUT 2400VA 1600 WATTS

Hallo, I own a NETUPS 450 (Model on the sticker: PRM 450i; upsstats reports "UPS 450 VA FW -0024") which perfectly works with the upscode2 driver. Maybe you want to add it to your list, even if the model is >10 years old. I suppose this is true for the whole series. According manual the come in the 450VA, 700VA, 1000VA and 1500VA strengths. They have been sold under different

Hi, just wanted to confirm that Fiskars UPS 9000 series (aka Powerware Plus 500 series) with optional UPS Information Unit works fine with upscode2 driver. Tested on Fiskars 9200 (20kVA/400V/3ph). Regards, -- Sebastian Zagrodzki Dzia? Sieciowy ICM, Uniwersytet Warszawski s.zagrodzki at net.icm.edu.pl (+48-22) 5520527, 8268009, fax. 8284195 http://www.net.icm.edu.pl/

Hi, I have a Comapq T2400H model 242688-003 and do not have the special cable to connect it to my serial port. I have tried all sorts of cable wirings that I found on the net, including ones for the powerware 5119 which appears to be the same model. I have read the documentation that comes with NUT, tried to read the source code and looked at the genericups code too.? I have

2012/2/6 thomas schorpp <thomas.schorpp at googlemail.com>: > Hi, Hi Thomas, > I want the driver report the battery status from ABM charging controllers > -patch attached- : thanks for your patch. since it introduces a new variable (battery.status.abm), I prefer to step back and think to something useful more widely. thus, I'm thinking about a generic

Hi, Am 13.02.2012 um 18:58 schrieb Arnaud Quette: > 2012/2/6 thomas schorpp <thomas.schorpp at googlemail.com>: >> Hi, > > Hi Thomas, > >> I want the driver report the battery status from ABM charging controllers >> -patch attached- : > > For now, I've tracked your patch here: >

I notice from the hardware compatibility list that the XR model is supported - what are the chances that the older R3000h models are too? Thanks. /Per Jessen, Z?rich

I tried to find a search button for the mailing list but could not. So rtfm me with the link please. If not.. I have an old Deltec PowerRite Pro 2 UPS which has a 9 pin serial cable. By trial and error Im pretty sure I found LB = DCD, but can not get the combination for OB / OL. No matter what I do I get the results below. driver.name: genericups driver.parameter.CP: CTS driver.parameter.LB:

Full_Name: Joseph Adler Version: 2.8.1 OS: Mac OS X 10.5.6 Submission from: (NULL) (71.142.93.52) According to the help file, the history() function is supposed to show recent command history. However, it does not do this in the current Mac OS X version. Instead, the history function appears to simply show the contents of the file ~/.Rhistory.

Hi all! I've been (very) out of the loop for a while, up to the point that I had completely missed that the mailing list has moved. Oh well. However, Kjell Claesson poked at me regarding the 3phase stuff, so I found out that I had missed the recent events. In any case, it seems that the situation is unchanged regarding 3phase support. As some of you remember I made a suggestion for a

Hi List. I have an old Compaq 3000 (Eaton 5119). It is running servers, disk-arrays, one workstation etc. I am planning to install NUT (master) on a headless CENTOS 6.8 system. Connect the UPS with seral cable. Now my main question is, Does NUT support the power segments on the UPS. My intention is to be able to take down the system in an ordered way before the batteries are exhausted. I.e 5 mins

Now I have some access problems. This is what ends up un messages Hosts.allow is set to accept anyone on the local net. Username and passwords are the same Upsc gives proper output. System is Centos 6.8 Jul 22 17:20:06 BIFROST upscode2[10113]: Startup successful Jul 22 17:20:06 BIFROST upsd[10116]: listening on ::1 port 3493 Jul 22 17:20:06 BIFROST upsd[10116]: listening on 192.168.0.1 port 3493

On Jul 22, 2017, at 4:13 AM, Tomas Larsson <tomas.larsson at enrad.se> wrote: > > I am planning to install NUT (master) on a headless CENTOS 6.8 system. > Connect the UPS with seral cable. It looks like this might be using the upscode2 driver (UPScode-II protocol), right? > Now my main question is, Does NUT support the power segments on the UPS. > My intention is to be able

On Sat, Jul 22, 2017 at 7:48 AM, Charles Lepple <clepple at gmail.com> wrote: > > I also have not used a Synology device, but as I recall, they generally > expect to be the NUT master system. This may cause problems if you need to > do something fancy with upssched. > The Synology boxes work fine as NUT clients, *however* they provide very little ability to configure NUT

Nut for Windows 2.6.3-3 + Eaton/PW 5110 (103004256-5591). I had to manually install libusb driver and I'm using bcmxcp_usb. upsd.exe is reporting to me "Out of memory". It will run, but once anything connects to the daemon, it dies with that message. I don't have much experience with NUT yet so I'm not sure what the next course of action is. I do have NUT for Windows

I've got a Powerware 5119 RM UPS. driver.list says to use "genericups upstype=20", however I know this UPS supports the UPS Code II protocol, so I wanted to use the upscode2 driver. It took some hacking but finally it works. I'm using NUT 2.4.1 and upscode2 driver version 0.87 (however the latest r2350 version of upscode2.c isn't significantly different, so I think all

All, I have a fairly old Compaq R3000h which is overdue for new batteries. Before I go and splash out a few hundred francs, I'd just need a quick sanity check - when I disconnect the power (UPS under load), it cuts out pretty much right away, so the batteries are flat (even though the charge indicator says full). When I reconnect the power, the surge triggers a 16A mains fuse. This sounds

Hello, I'm a recent convert to dovecot from courier-imap and the performance has certainly improved. I'm running the vanilla 1.0.7 version that came with the CentOS 5.2 x86_64 distro. I've come across a similar problem that was posted by Ralf Hildebrandt earlier this year under the same subject, but that thread just seems to have died off. I'm also using per- user maildirsize

THANKYOUTHANKYOUTHANKYOUTHANKYOU!!!!!! There was a smaller patch posted to the list for lines -1389,9 +1390,10 a couple years ago, it helped some - BUT - it was still buggy. I have a Compaq R3000, I will get this patch integrated pronto and test Note that since the UPS relies on the voltage from the battery pack to determine state of charge, it is quite useful to add in the battery pack

I've followed the recent thread on caller id with UK British Telecom networks (where the caller id data is delivered before the first ring). My understanding is that if I use a recent CVS head (e.g. CVS-HEAD-09/18/04-17:45:52) and a TDM400 with FXO modules, all I need to do is include the line: usecallerid=uk In my zapata.conf (in the [channels] section) I've done this, but I get: Sep