similar to: compaq r3000 triggering the fuse when power is reconnected

Hi All, I put my Compaq R3000 UPS on NUT. Every once in a while the battery alarm light turns on, on the front of the UPS. Maybe once every couple of days or so. When that happens I get the following output in /var/log/messages: Sep 22 01:51:46 mail upscode2[90734]: Unknown response to UPDS: .20 MOUL1 Sep 22 01:51:46 mail upscode2[90734]: Unknown response to UPDS: 0119.20 MOIL1 Sep 22

On Sat, Jul 22, 2017 at 7:48 AM, Charles Lepple <clepple at gmail.com> wrote: > > I also have not used a Synology device, but as I recall, they generally > expect to be the NUT master system. This may cause problems if you need to > do something fancy with upssched. > The Synology boxes work fine as NUT clients, *however* they provide very little ability to configure NUT

I notice from the hardware compatibility list that the XR model is supported - what are the chances that the older R3000h models are too? Thanks. /Per Jessen, Z?rich

Hello list, I recently loaded CentOS 4.2 x86_64 on a Compaq R3000 laptop and then fully updated to 4.3. The battery applet on other installs always just showed up and worked, not so here. It is not in the applet choices at all, it is available here on my desktop. I suspect it is something simple I'm missing but I need a point in the right direction. I did try: yum remove and yum install

Now I have some access problems. This is what ends up un messages Hosts.allow is set to accept anyone on the local net. Username and passwords are the same Upsc gives proper output. System is Centos 6.8 Jul 22 17:20:06 BIFROST upscode2[10113]: Startup successful Jul 22 17:20:06 BIFROST upsd[10116]: listening on ::1 port 3493 Jul 22 17:20:06 BIFROST upsd[10116]: listening on 192.168.0.1 port 3493

Hi List. I have an old Compaq 3000 (Eaton 5119). It is running servers, disk-arrays, one workstation etc. I am planning to install NUT (master) on a headless CENTOS 6.8 system. Connect the UPS with seral cable. Now my main question is, Does NUT support the power segments on the UPS. My intention is to be able to take down the system in an ordered way before the batteries are exhausted. I.e 5 mins

Hi Matthijs, > Arnaud. >After some trial and error, i found out that the HP R3000 XR ups's we have >can be used with Network Ups Tools. >This using the bcmxcp driver. > >Note that in the code of this driver (line 1420) , the Baudrate is fixed to >9600 baud. >to connect to a serial HP R3000 XR ups one needs to change this to 19200 >baud. > >ideally, this should

Hi, So far I've gleaned heaps of useful info from the list and got mostly running with NUT. There was a thread by Paul Battaglia and Kjell Claesson about the R3000 which has helped me get so far, but now with the patched driver I still have this on startup: # /usr/local/ups/bin/upsdrvctl start Network UPS Tools - UPS driver controller 2.0.5 Network UPS Tools - BCMXCP UPS driver 0.11

On Jul 22, 2017, at 4:13 AM, Tomas Larsson <tomas.larsson at enrad.se> wrote: > > I am planning to install NUT (master) on a headless CENTOS 6.8 system. > Connect the UPS with seral cable. It looks like this might be using the upscode2 driver (UPScode-II protocol), right? > Now my main question is, Does NUT support the power segments on the UPS. > My intention is to be able

Hi I have a HP R3000 XR UPS which NUT never says is at 100% battery. It seems stuck in 98 or 99 . something percentage. How accurate should i expect the reports to be? All my other UPSes has been and is at 100%, even those i have retired. My monitor system runs debian. The host that is physically connected to this ups runs: nut 2.2.2-6.4 The web script runs nut-cgi 2.0.4-4 JonB

Hello, Does anyone here happen to have a copy of the firmware for this UPS? Any links on the HPE website I could find (pointing to the old HP) are long dead. Thanks! Marek

Hi All, I'm trying to communication with the HP r3000 XR UP using the latest stable build and I'm getting the following errors. Can anyone enlighten me with the errors below and what other course of action I can take. Thanks in advance. Paul. [root@WRRFtpServer etc]# /usr/local/ups/bin/upsdrvctl start Network UPS Tools - UPS driver controller 2.0.5 Network UPS Tools - BCMXCP UPS

UPS: HP R3000 XR with HP UPS Management Module What I Want: I just want the UPS to shut down the client called "tor" before the UPS power drains out, I'd prefer to use a direct serial cable instead of network, in case the network doesn't work. I'll manage the UPS trough the ethernet using the built-in HTTP webinterface in the HP UPS Management Module. I've created a

Hi! Have a similar issue with one of our customers having HP R12000/3 UPS with AF430A card. Upsmon shows the UPS as Online, on Battery and Battery discharging at the same time: [root at smrsrvslv06 lib64]# upsc hpups at localhost ambient.temperature: 19.0 ambient.temperature.high: 0.00 ambient.temperature.low: 0.00 battery.charge: 94.00 battery.current: 0.00 battery.runtime: 4620.00

My UPS is an Exide NetUPS SE PRC1500i (1500 VA), also known as Powerware 5119, according to Karl Schmidt (http://lists.alioth.debian.org/pipermail/nut-upsuser/2005-July/000026.html) also Deltec PowerRite Pro II, and according to http://www.usedups.de/compaq_ups.html also Compaq R3000h. I am not sure if the information in http://www.bps.hu/powerware/model_en.html is to be interpreted as that it was

My UPS is an Exide NetUPS SE PRC1500i (1500 VA), also known as Powerware 5119, according to Karl Schmidt (http://lists.alioth.debian.org/pipermail/nut-upsuser/2005-July/000026.html) also Deltec PowerRite Pro II, and according to http://www.usedups.de/compaq_ups.html also Compaq R3000h. I am not sure if the information in http://www.bps.hu/powerware/model_en.html is to be interpreted as that it was

Hello Arnaud, On 05/04/14 22:01, Arnaud Quette wrote: > Philippe, Ivan, > > please see https://github.com/networkupstools/nut/issues/118 > and send back your data. I've pasted the requested files in github, but the auto-formatting may have damaged them, so here they are. Also, when I ran gen-snmp-subdriver.sh, it gave me the following message:

Philippe, Ivan, please see https://github.com/networkupstools/nut/issues/118 and send back your data. cheers Arno -------------- next part -------------- An HTML attachment was scrubbed... URL: <http://lists.alioth.debian.org/pipermail/nut-upsuser/attachments/20140405/682f10dd/attachment-0001.html>

I have setup nut-2.4.1 with the bcmxcp driver for my HP R3000 XR unit and although it appears to work, I receive the following sorts of errors in syslog: Aug 27 10:33:05 sv18 bcmxcp[6373]: Communications with UPS lost: Receive error (data): got 0 bytes instead of 64!!! Aug 27 10:33:15 sv18 bcmxcp[6373]: Communications with UPS lost: Receive error (data): got 0 bytes instead of 64!!! Aug 27

Hi Users NUT, I want monitor a UPS of brand SMS (Sinus Double 8 KVA) using a raspberry-pi. In compatibility list, is listed to use the blazer_ser driver. I use a USB adapter to RS-232 conected in to the No-Breake. Follow the comands e confs. root at rasp:/home/pi# lsusb *Bus 001 Device 004: ID 067b:2303 Prolific Technology, Inc. PL2303 Serial Port* Bus 001 Device 003: ID 0424:ec00 Standard