similar to: Megatec_USB on OpenBSD 4.3 - again...

Hi! I am trying to get an Atlantis-Land 1501 UPS to work under OpenBSD. The UPS works OK under Linux + megatec_usb driver+nut_2.2.2. What I get under OpenBSD is: root at puffwall:~ # dmesg OpenBSD 4.3 (GENERIC) #698: Wed Mar 12 11:07:05 MDT 2008 deraadt at i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel Pentium III ("GenuineIntel" 686-class, 128KB L2

Hi! I am trying to get an Atlantis-Land 1501 UPS to work under OpenBSD. The UPS works OK under Linux + megatec_usb driver+nut_2.2.2. What I get under OpenBSD is: root at puffwall:~ # dmesg OpenBSD 4.3 (GENERIC) #698: Wed Mar 12 11:07:05 MDT 2008 deraadt at i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC cpu0: Intel Pentium III ("GenuineIntel" 686-class, 128KB L2

Hello, I 'm trying to set up an Eaton PW5110 using nut-2.4.1 in OpenBSD, my ups.conf follows : [myups] driver = bcmxcp_usb port = auto desc = "Eaton PW 5110 (1500VA)" My first attempt to run upsdrvctl ended up complaining about unimplemented usb_clear_halt() in libusb. I patched libusb-0.1.12 with the following patch :

Hi all! I have a ups Ippon smart power pro 2000. And it connects to my FreeBSD 7.2 x86 server throught usb. I'm try to setup it in nut with megatec_usb driver... But it is not recognizes ups. I'm try set productid and vendorid in ups.conf, but this is not help. Nut version 2.4.1 below i'm add output of lsusb, my ups.conf and /usr/local/libexec/nut/megatec_usb -a IPPON -DDD

Hallo, Following the tips found at https://calomel.org/nut_ups.html I was trying to make NUT operate "APC Back UPS CS-350". The device introduces itself as: #v+ ugen0 at uhub0 port 1 "American Power Conversion Back-UPS CS 350 FW:807.q7.I USB FW:q7" rev 1.10/0.06 addr 2 #v- My config: #v+ [apc] driver = usbhid-ups port = /dev/ugen0.00 pollfreq =

Hallo, Following the tips found at https://calomel.org/nut_ups.html I was trying to make NUT operate "APC Back UPS CS-350". The device introduces itself as: #v+ ugen0 at uhub0 port 1 "American Power Conversion Back-UPS CS 350 FW:807.q7.I USB FW:q7" rev 1.10/0.06 addr 2 #v- My config: #v+ [apc] driver = usbhid-ups port = /dev/ugen0.00 pollfreq =

Hi all! Maybe possible adds something in megatec_usb driver for normal working with ippon 2000? This is output for drivers megatec_usb and blazer_usb: =========================================================== gate# /usr/local/libexec/nut/megatec_usb -DDDD -a IPPON Network UPS Tools - Megatec protocol driver 1.6 (2.4.1) Serial-over-USB transport layer 0.10 debug level is '4' Checking

after I starting battery test on my laptop I see in my logs some error and ups (IPPON Smart Power Pro 1400. usb interface) isn't monitoring now [ippon] driver = megatec_usb port = auto desc = "local" Feb 16 23:22:09 f37 upsd[17150]: Instant command: stlk at 127.0.0.1 did test.battery.start on ippon Feb 16 23:22:12 f37 megatec_usb[17249]: ser_get_line: Device detached? (error

Hi Alexey, Please post the output of 'lsusb' and 'megatec_usb -a sven_625 -u nut -DDDDD'. On Monday 15 June 2009 14:32:16 you wrote: > Package: nut > Version: 2.4.1-3 > Severity: normal > > I have a SVEN Pro+ 625 ups that uses megatec_usb driver. > In ups.conf I describe it like: > [sven_625] > driver = megatec_usb > port = auto > desc =

2010/10/18 Michael Eitelwein > Hi Arnaud > Hi Michael, > Yes, did test it without success. > can you please post the first 20 seconds running blazer_usb in debug mode, ie: $ sudo /lib/nut/blazer_usb -DDD -a cyberpower aside from fixing the megatec situation, ensuring that you'll be able to run the replacement is also to be considered ;-) now, for the megatec issue, we need

Hey all, thanks for your work on nut. I recently got myself a new cheap UPS, and have thus far determined very little about it. I can run whatever you like to help identify and work with it. So far I've played around with various settings and have had some limited success with the megatec_usb driver (Debian testing version): ----ups.conf---- [plexus] driver=megatec_usb model=500VA mfr=Plexus

Hi, Just purchashed this UPS. The megatec_usb driver appears to be communicating with the UPS - however, the ups.status field always states "off" /usr/local/ups/bin/megatec_usb -a plexus -DD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] Andrey Lelikov (c)

Hi, Just purchashed this UPS. The megatec_usb driver appears to be communicating with the UPS - however, the ups.status field always states "off" /usr/local/ups/bin/megatec_usb -a plexus -DD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues (c) 2003-2007 Serial-over-USB transport layer for Megatec protocol driver [megatec_usb] Andrey Lelikov (c)

ut 2.4.1 works with megatec_usb driver. It tries to interact with a device in /dev/bus/usb/X/Y, but there are root:root 664 access rights. When I try to set port /dev/hiddev0 with write access in config file, in strace there are no records about accessing /dev/hiddev, but still only /dev/bus/usb/X/Y How to explain such a behavior? execve("./megatec_usb",

Citeren Roman Mamedov <roman at rm.pp.ru>: >> Another useful thing would be to run the bundled driver on a Windows >> box while running 'usbsnoop' so that we can get an idea what it is >> doing. Maybe we're missing something here. I still would like to see that. > Keep in mind that the patched megatec_usb driver (which I use since > yesterday) can

Hi everyone, I have a belkin ups that was bought around 2 months ago. It seems like the driver doesn't like the UPS, although on the website it's listed as supported. This is on a gentoo system with nut 2.2.1 . megatec_usb output: ---------SNIP---------- digamma nut # ./megatec_usb -a belkinm -DDDDDD Network UPS Tools 2.2.1 - Megatec protocol driver 1.5.9 [megatec_usb] Carlos Rodrigues

Trying to use it with Sven Smart RM2000 (seems to be an OEM clone of Sysgration Smart RM UPS: http://www.sysgration.com/product.asp?KID=7). I have just compiled the latest svn trunk. Unfortunately it does not work with that UPS: dbely at vserver1:~/nut-svn$ sudo /usr/local/ups/bin/megatec_usb -u root -a myups Network UPS Tools 2.1.0 - Megatec protocol driver 1.5.3 [megatec_usb] Carlos Rodrigues

Hi Bj?rn, 2009/10/9 Bj?rn Torkelsson > Public bug reported: > > Binary package hint: nut > > I have recently upgraded from hardy to intrepid to jaunty. After > upgrading to Intrepid the megatec_usb stopped recognizing my Trust PW- > 4130M ups, it still does not work on Jaunty. It worked without any > problems in hardy. > > I tried the megatec_usb driver from hardy

Hi, I'm new in the list and I'm having a little bit trouble to put the megatec_usb to work. I've been using NUT for a while with the apc and megatec driver (serial), with no problem. The server is a Ubuntu 8.04.2 with NUT version 2.2.1-2.1ubuntu7.2, the default package version in this ubuntu release. I've configured the ups.conf as follows: [sms] driver = megatec_usb

Hi, I'm new in the list and I'm having a little bit trouble to put the megatec_usb to work. I've been using NUT for a while with the apc and megatec driver (serial), with no problem. The server is a Ubuntu 8.04.2 with NUT version 2.2.1-2.1ubuntu7.2, the default package version in this ubuntu release. I've configured the ups.conf as follows: [sms] driver = megatec_usb