similar to: MGE Pulsar EX over serial problem (FreeBSD)

Hi, I have the above UPS connected to a FreeBSD 6.2 box and it shows 'data stale' very frequently (every few minutes). I have tried the usual trick of setting maxage, poll interval, etc etc but to no avail. When I wind up logging I see (on mge-shut) entering shut_get_report(id: 0d, len: 1800) shut_wait_ack(): ACK received entering shut_get_report(id: 16, len: 1800) shut_wait_ack():

Hi, I am trying to talk to an MGE Pulsar Extreme UPS over RS232 with the mge-shut driver but I'm having some problems. It appears to init OK but I can't, say, turn the outlets off, eg.. harrow:~>upsc mge@localhost battery.charge: 78 battery.charge.low: 20 battery.runtime: 05760 driver.name: mge-shut driver.parameter.port: /dev/cuad1 driver.version: 2.0.3 driver.version.internal: 0.65

Hi, I am trying to talk to an MGE Pulsar Extreme UPS over RS232 with the mge-shut driver but I'm having some problems. It appears to init OK but I can't, say, turn the outlets off, eg.. harrow:~>upsc mge@localhost battery.charge: 78 battery.charge.low: 20 battery.runtime: 05760 driver.name: mge-shut driver.parameter.port: /dev/cuad1 driver.version: 2.0.3 driver.version.internal: 0.65

I have trouble in getting communication work with MGE Ellipse 500. I bought it second hand and I don't have the cable for it. How do I know if it's the Serial or USB model? The serial number of the unit is: 769B16015. I suspect it is the serial version as the label next to the RJ11 stands "com port", but I can't be 100% sure. MGE Ellipse serial cable pinout can be found

Hi, I've been using NUT for many years to look after the UPS on my home servers. Originally I was using a Compaq R3000 but that was replaced with an MGE Pulsar Evolution 3000 about a couple of years ago because the Compaq one was just too noisy! I'm just setting up a replacement server and would like to connect it using a serial cable as I've found that the USB connection

Hello Arno, > Question: have you also tested oldmge-shut? > Otherwise, that might be interesting to do so and send back the > results of these tests... Yes, I've tried this as well with worse results unfortunately. This driver seems to be even more unstable. When it gets able to set communication with the UPS (which is not always the case), it usually lost it again after a while.

Hello Arno, Can apply the patch directly or should I recompile nut? Best regards, Panagiotis On 3/4/2015 5:06 ??, Arnaud Quette wrote: > Hello Panagiotis > > 2015-04-03 14:28 GMT+02:00 Panagiotis Kritikakos > <panagiotis.kritikakos at nikitec.gr > <mailto:panagiotis.kritikakos at nikitec.gr>>: > > Hello Arno, > > Question: have you also

Hello Arno, Thanks for the quick reply. FreeNAS is FreeBSD-based. Yes, I could test a patch. As I have mentioned, this behavior is not seen at every single reboot but after most reboots. Also, some times, the connectivity can be lost without even rebooting. That is not very often can have happened a few times. Best regards, Panagiotis On 2/4/2015 5:44 ??, Arnaud Quette wrote: > Hello

Hi all, I just changed my old MGE ellipse for a evolution 850 (now eaton). I can connect using mge-shut (newmge-shut doesn't work). But I have a few issues. I lloked around on NUT web-site and googled with no luck. Using debian lenny on 2.6.18 kernel (due to some ISDN driver that doesn't work with earlier kernels) 1) the most annoying is that I cannot shutdown the UPS. here is a trace :

Hello, I forgot nut since more than a year because a lot of job with other application My server nut failed since severals months We had 3 electric failure so I must install a new server nut I work with ubuntu 10.04.4 (64bits) / I installed nut 2.4.3 with deposits I have a MGE Pulsar evolution 2200 connected on usb last week when I began my tests all was ok (communication etc etc ..)

Hello all, OS name: FreeNAS 9.3 NUT version: 2.7.2 NUT installed method: Bundled with FreenNAS 9.3 Device: EATON 5SC 1000 (http://powerquality.eaton.com/Products-services/Backup-Power-UPS/5SC.aspx?cx=5&wtredirect=www.eaton.com/5SC&GUID=B81251A4-F34E-4373-94B3-B4FB3D0CBCA8) Problem description: This was originally reported as bug to FreeNAS

Hello Panagiotis 2015-04-03 14:28 GMT+02:00 Panagiotis Kritikakos < panagiotis.kritikakos at nikitec.gr>: > Hello Arno, > > Question: have you also tested oldmge-shut? >> Otherwise, that might be interesting to do so and send back the results >> of these tests... >> > Yes, I've tried this as well with worse results unfortunately. This driver > seems to

Hi Panagiotis 2015-04-06 9:13 GMT+02:00 Panagiotis Kritikakos < panagiotis.kritikakos at nikitec.gr>: > Hello Arno, > > Can apply the patch directly or should I recompile nut? > not sure to fully understand your comment, but... this is a source code patch, so you indeed have to apply it to the NUT source code (from within the source tree, "patch -p1 <

Hello Arno, FreeNAS doesn't come with a compiler and I had to compile with the patch on FreebBSD-9.3 and then copy the produced mge-shut. Unfortunately it didn't work out. For every try I was getting "Connection Refused" and when I tried /usr/local/libexec/nut/mge-shut -D -a <ups_name> I was always getting 'No matching HID UPS found'. I returned back to the

Hello! We have two upses: MGE Pulsar M 3000 and MGE Pulsar EXtreme 3200C. They connect to server by USB. EXtreme works good with usbhid-ups (nut 2.2.1) and newhidups (nut 2.0.5). But Pulsar M doesn't want to work with usbhid-ups. - my ups.conf: [extreme] driver = usbhid-ups port = auto product = "EXtreme" [pulsar] driver = usbhid-ups port =

(Sorry, I accidentally discarded the wrong message in the moderation queue - please subscribe to the list to avoid this in the future.) > From: <onyx at netfusion.fr> > Subject: [HCL] MGE Pulsar Evolution 1100 - not recognized by USB driver > Date: December 22, 2011 12:15:16 AM EST > To: <nut-upsuser at lists.alioth.debian.org> > > > Hi everybody, > > It

Hi! I have a MGE Pulsar ES 8+ UPS. Here is the response of some commands: - Si --> 3000 44 0 - Si 1 --> Pulsar ES8+ 0 - Ai --> 5 0 It's not recognized very well by the current (from CVS) mge-utalk driver: [root@srv01 ~]# /home/rog/src/nut/drivers/mge-utalk -i 20 -DDD -u root /dev/ttyS0 Network UPS Tools - MGE UPS SYSTEMS/U-Talk driver 0.86 (2.1.0) debug level is '3'

Hello, My MGE Pulsar Evolution 800 had some hardware troubles (it may be the batteries according to the manual). The fault was not detected so the power was cut to the load and nothing appears in the log files. Arnaud: do you know if the UPS have some way to report this kind of troubles to the PC so that NUT can handle it with a shutdown sequence ? Philippe

Hello, I'm trying to communicate with a MGE Pulsar STS 16 using nut under Linux, but I've had no luck so far. I haven't saw it supported in the doc, so if there's anything I can try... Thanks, Arnaud. -- Perso: http://launay.org/blog/ H?bergement: http://www.nocworld.com/

Hi, My UPS is MGE Pulsar Ellipse Premium 1200VA, connected on USB port, usbhid-ups driver. Using simply KNotify about UPS connection states I noticed that sometimes unpredictably a notification appears that the USB connection to the UPS is lost and a few seconds later another notification appears that the connection is restored. And this repeats to infinity. The only way to get out of it is to