similar to: MGE Ellipse 500 cable config

Hi all, I just changed my old MGE ellipse for a evolution 850 (now eaton). I can connect using mge-shut (newmge-shut doesn't work). But I have a few issues. I lloked around on NUT web-site and googled with no luck. Using debian lenny on 2.6.18 kernel (due to some ISDN driver that doesn't work with earlier kernels) 1) the most annoying is that I cannot shutdown the UPS. here is a trace :

Hello Arno, > Question: have you also tested oldmge-shut? > Otherwise, that might be interesting to do so and send back the > results of these tests... Yes, I've tried this as well with worse results unfortunately. This driver seems to be even more unstable. When it gets able to set communication with the UPS (which is not always the case), it usually lost it again after a while.

Hello Arno, Thanks for the quick reply. FreeNAS is FreeBSD-based. Yes, I could test a patch. As I have mentioned, this behavior is not seen at every single reboot but after most reboots. Also, some times, the connectivity can be lost without even rebooting. That is not very often can have happened a few times. Best regards, Panagiotis On 2/4/2015 5:44 ??, Arnaud Quette wrote: > Hello

Hello Arno, Can apply the patch directly or should I recompile nut? Best regards, Panagiotis On 3/4/2015 5:06 ??, Arnaud Quette wrote: > Hello Panagiotis > > 2015-04-03 14:28 GMT+02:00 Panagiotis Kritikakos > <panagiotis.kritikakos at nikitec.gr > <mailto:panagiotis.kritikakos at nikitec.gr>>: > > Hello Arno, > > Question: have you also

Hello all, OS name: FreeNAS 9.3 NUT version: 2.7.2 NUT installed method: Bundled with FreenNAS 9.3 Device: EATON 5SC 1000 (http://powerquality.eaton.com/Products-services/Backup-Power-UPS/5SC.aspx?cx=5&wtredirect=www.eaton.com/5SC&GUID=B81251A4-F34E-4373-94B3-B4FB3D0CBCA8) Problem description: This was originally reported as bug to FreeNAS

We have several systems in remote locations and I have found that the ones in the US are having issues.. We are an Australian company and can't source a 110V UPS locally so we arrange to have one bought for the site when it's installed. It seems that in the US we are getting "Pulsar EX 1500" UPSs but locally we buy "Pulsar 1500". NUT seems to work find with the

Hello Panagiotis 2015-04-03 14:28 GMT+02:00 Panagiotis Kritikakos < panagiotis.kritikakos at nikitec.gr>: > Hello Arno, > > Question: have you also tested oldmge-shut? >> Otherwise, that might be interesting to do so and send back the results >> of these tests... >> > Yes, I've tried this as well with worse results unfortunately. This driver > seems to

Hi Panagiotis 2015-04-06 9:13 GMT+02:00 Panagiotis Kritikakos < panagiotis.kritikakos at nikitec.gr>: > Hello Arno, > > Can apply the patch directly or should I recompile nut? > not sure to fully understand your comment, but... this is a source code patch, so you indeed have to apply it to the NUT source code (from within the source tree, "patch -p1 <

Hello Panagiotis 2015-04-01 16:28 GMT+02:00 Panagiotis Kritikakos < panagiotis.kritikakos at nikitec.gr>: > Hello all, > > OS name: FreeNAS 9.3 > NUT version: 2.7.2 > NUT installed method: Bundled with FreenNAS 9.3 > Device: EATON 5SC 1000 (http://powerquality.eaton. > com/Products-services/Backup-Power-UPS/5SC.aspx?cx=5& >

Hello Arno, FreeNAS doesn't come with a compiler and I had to compile with the patch on FreebBSD-9.3 and then copy the produced mge-shut. Unfortunately it didn't work out. For every try I was getting "Connection Refused" and when I tried /usr/local/libexec/nut/mge-shut -D -a <ups_name> I was always getting 'No matching HID UPS found'. I returned back to the

Hi, I am trying to talk to an MGE Pulsar Extreme UPS over RS232 with the mge-shut driver but I'm having some problems. It appears to init OK but I can't, say, turn the outlets off, eg.. harrow:~>upsc mge@localhost battery.charge: 78 battery.charge.low: 20 battery.runtime: 05760 driver.name: mge-shut driver.parameter.port: /dev/cuad1 driver.version: 2.0.3 driver.version.internal: 0.65

Hi, I am trying to talk to an MGE Pulsar Extreme UPS over RS232 with the mge-shut driver but I'm having some problems. It appears to init OK but I can't, say, turn the outlets off, eg.. harrow:~>upsc mge@localhost battery.charge: 78 battery.charge.low: 20 battery.runtime: 05760 driver.name: mge-shut driver.parameter.port: /dev/cuad1 driver.version: 2.0.3 driver.version.internal: 0.65

Hi, I have the above UPS connected to a FreeBSD 6.2 box and it shows 'data stale' very frequently (every few minutes). I have tried the usual trick of setting maxage, poll interval, etc etc but to no avail. When I wind up logging I see (on mge-shut) entering shut_get_report(id: 0d, len: 1800) shut_wait_ack(): ACK received entering shut_get_report(id: 16, len: 1800) shut_wait_ack():

Hi, I've been using NUT for many years to look after the UPS on my home servers. Originally I was using a Compaq R3000 but that was replaced with an MGE Pulsar Evolution 3000 about a couple of years ago because the Compaq one was just too noisy! I'm just setting up a replacement server and would like to connect it using a serial cable as I've found that the USB connection

Hi everyone, This is not directly NUT related, but i don't know where else I can still ask this. I have been using a pretty decent 2nd hand MGE ellipse premium 1200VA for a while now at home. http://www.mgeups.com/download/doc_intl/ small/premium/389uk.pdf It's been working very well for me on linux, but my linux server has recently passed away and now I only have Macs left.

2009/5/16 Arnaud Quette <aquette.dev at gmail.com> > > > 2009/5/7 Daniel O'Connor <doconnor at gsoft.com.au> > >> On Wed, 6 May 2009, Arnaud Quette wrote: >> > I think I've found something, but I would need an upsd debug output >> > (level 3) to see what going on the state socket. >> >> I've attached a log for you. >>

I have an MGE Ellipse Premium 1200 that I connected to my server using its USB cable. Nut seems to be working fine. I've done a power down test and it worked and came back up when the UPS had power again. I'm using the newhidups driver and the USB cable. The problem I'm having is that if I boot with the cable connected newhidups says it can't find the UPS. If I unplug and plug in

Hello! I've been following this list for several weeks now and would like to purchase some hardware for a VOIP/ voice-mail solution. This card appears strikingly similar to a modem. Is it? Is there a product to bring in more than one POTS line short of a full T1? It just seems silly that the technology hasn't advanced any further than to have a single line per card. Any thought

Anybody using Siemens optiPoint 300 H.323 phones? I saw a few references to them in the archives of this list, and the Wiki seems to be down. I have a chance to pick up a bunch of these, cheap. Questions: * Asterisk support? * What sort of power supplies will they need? The bunch I am looking at are surplus and have no supplies. Thanks, </edg> Ed Greenberg San Jose, CA

Hi I'm looking for a pinout for the above. Note this has what i'd call RJ45 sockets (or someone smart can correct me). I need to plug into BT (rj13?). And, yes I've googled (glad I'm not chinese) and have tried the suggested, just plug in a 6 connector rj11 and i didnt work atall. On a side note, I cannot beleive that Digium dont have this information on there site, it