similar to: megatec_usb subdrivers for PowerMust 600 USB?

Hi, a few days ago, I bought some of those Mustek UPSes that have both a serial and a USB connector. Currently only the serial port is supported by the megatec driver. This works fine so far. Now I have seen there is a megatec_usb driver, which currently only supports 2 other UPSes. How can I help to find out whether the PowerMust might actually work with the megatec_usb driver? -- Regards,

Hello, I'm working on getting nut using a Powermust Office 650 USB USV. Using today's trunk megatec_usb detects its vendorid 0665 productid 5161 but uses the agiler driver for it which apparently does not work (timeout...). I think this device is using that USB-to-serial chip but a different protocol behind. I got the phoenix subdriver working with the device but I had to extend

Hi! I am trying to install subj, on my Bubba miniserver, that runs Debian. I am stoped now with driver test: upsdrvctl start Network UPS Tools - UPS driver controller 2.0.4 Network UPS Tools - Megatec protocol driver 1.4 (2.0.4) Carlos Rodrigues (c) 2003-2006 Unable to open : No such file or directory Things to try: - Check 'port=' in ups.conf - Check owner/permissions of all

Hello all: I have a Yukai PowerMust 1000 USB and it used to work on another computer using megatec_usb driver. Now, I have it in a new computer, but the driver does not detect it. It is there: # lsusb|grep Cypress Bus 006 Device 007: ID 0665:5161 Cypress Semiconductor USB to Serial Permissions are OK: # ls -l /dev/bus/usb/006/007 crw-rw-r-- 1 root nut 189, 646 ago 8 01:51

Hi, I'm trying to setup my Mustek 600 with USB (no serial ports on my computer) on Gentoo. The configuration I use is: [Mustek] driver = megatec_usb port = auto desc = "Power Mustek 600 USB" The NUT I use on my x86_64 machine is: sys-power/nut-2.4.3-r2 USE="bash-completion ssl usb xml -cgi -hal -snmp" When I start upsdrv I get: weasel ~ # /etc/init.d/upsdrv start

Hi, I'm not the maintainter for the "megatec_usb" driver (in fact, I'm no longer maintainer for the base "megatec" either), so I don't really know the status for that particular UPS. I'm forwarding this to the NUT mailing-list though. Regards, -- Carlos Rodrigues On Fri, Dec 5, 2008 at 10:30 AM, Adrian Czerniak <adrian.czerniak at becomo.com> wrote:

Hi, I'm not the maintainter for the "megatec_usb" driver (in fact, I'm no longer maintainer for the base "megatec" either), so I don't really know the status for that particular UPS. I'm forwarding this to the NUT mailing-list though. Regards, -- Carlos Rodrigues On Fri, Dec 5, 2008 at 10:30 AM, Adrian Czerniak <adrian.czerniak at becomo.com> wrote:

On 2/27/07, Markus Layr <tuxian@yahoo.de> wrote: > do you now if there is a possibility to get an connection betwenn nut an > the Mustek PowerMust 2000VA via USB? > I tried if with newhidups but I always got "No matching HID UPS found". In the latest development version of NUT there's a new driver called "megatec_usb" that may support your UPS. If it

Hi Vitaly, 2009/2/26 Vitaly Polyakov <var at fapu.ru> > Hello. > > You are the site administrator Project Network UPS Tools, are not you? I > think? it is a good idea to add information about the compatibility the > NUT with a Mustek PowerMust 424/636/848 USB. These UPS are using > modified protocol, and therefore the old driver megatec_usb is not > suitable and the

Hello, It looks like the nut-upsuser list is momentarily down. That's why I send it to nut-upsdev list too. I have recently bought a mustek Powermust 1000VA USB (sadly not the USB P version). I have done some tests with the latest nut 2.2.0 megatec and megatec_usb drivers. Here are my feedbacks. It works quite well but is extremely noisy in battery mode (and that is not the noise of the

Hello, It looks like the nut-upsuser list is momentarily down. That's why I send it to nut-upsdev list too. I have recently bought a mustek Powermust 1000VA USB (sadly not the USB P version). I have done some tests with the latest nut 2.2.0 megatec and megatec_usb drivers. Here are my feedbacks. It works quite well but is extremely noisy in battery mode (and that is not the noise of the

Arnaud Quette wrote: > Anyhow, I would more see this as a merge of all these drivers, with > some autodetection or flag/param to switch the mfr/model and maybe > capabilities... Whatever the driver name is, a good thing would be the > name of the protocol or something generic enough, though powermust is > fine. Ok, I made some minor changes to powermust, to make it less

Hi, I have a powermust with a usb connector. I searched the archive and found this post: http://lists.alioth.debian.org/pipermail/nut-upsdev/2006-April/000816.html Must I abandon hope of controlling this UPS via USB with NUT? Added this line to /etc/udev/rules.d/70-nut-usbups.rules: # OMRON - usbhid-ups SYSFS{idVendor}=="06da", SYSFS{idProduct}=="0003",

Disclaimer: I've setup APC UPS monitoring and it works... ... but when it comes to mustek powermust 600usb (connected via com-port), I can't make it work. Got NUT installed via aptitude in ubuntu feisty and a basic setup, exactly the same as for the apc, except for the name of the ups and the corresponding section of ups.conf -- [mustek] driver = megatec port = /dev/ttyS1

A non-text attachment was scrubbed... Name: not available Type: application/pgp-signature Size: 188 bytes Desc: not available Url : http://lists.alioth.debian.org/pipermail/nut-upsdev/attachments/20071124/3ceb35d2/attachment.pgp

Hi folks, has anyone been successful in getting a Mustek PowerMust 500 to talk to nut? All my attempts (tried "mustek" and "powermust" as drivers) have been unsuccessful so far. Thanks for any clues. Sascha -- http://yoyodyne.ath.cx

Hi Sven, 2008/1/25, Sven Koch <haegar at sdinet.de>: > Package: nut > Version: 2.2.1-1 > Severity: normal > > I am using a Mustec PowerMust 1000 USB, connected with a USB cable to > the PC. > > With nut 2.2.0-2.1 everything works without problems - but since the > 2.2.1-1 update the "upsdrvctl start" from the init script just fails, > executing the

Hi, I'm having a hard time configuring a Mustek Powermust 600VA ups to work via USB with nut. I read somewhere that nut works OK via the rs232 cable, but unfortunately I don't have a COM port in my computer. The kernel detects the ups as an Xbox pad :) and loads the xpad module. I tried running /lib/nut/megatec with different /dev/ttySx but it displays megatec protocol UPS was not

--- Arjen de Korte <nut+users at de-korte.org> wrote: > > > I also did: > > > > # ./megatec_usb -DDDDD -x vendor=06da -x mfr=OMRON > > /dev/usb/hiddev0 > > Please have a look at 'man 8 megatec_usb' again. > > You probably need to specify the '-x vendorid' and > '-x productid' options > and most likely, the

--- Arjen de Korte <nut+users at de-korte.org> wrote: > > > I also did: > > > > # ./megatec_usb -DDDDD -x vendor=06da -x mfr=OMRON > > /dev/usb/hiddev0 > > Please have a look at 'man 8 megatec_usb' again. > > You probably need to specify the '-x vendorid' and > '-x productid' options > and most likely, the