similar to: Re: UPS data.

2. Recommendations? My use case is pretty typical. I have one Linux machine I want to protect, automated shutown is desirable, blackouts longer than a hour are very rare at my location (the last one I can remember was in 1993), brownouts are very rare and mild, but summer thunderstorms are common and can be severe. I'm a good match for your typical consmer-grade UPS. 2a. In 2009, what do

OS name and version: pi at raspberrypi ~ $ cat /etc/*release PRETTY_NAME="Debian GNU/Linux 7.0 (wheezy)" uname -a Linux raspberrypi 3.6.11+ #393 PREEMPT Fri Mar 8 16:36:28 GMT 2013 armv6l GNU/Linux exact NUT version pi at raspberrypi ~ $ dpkg -s nut Package: nut ... Version: 2.6.4-2.3 NUT installation method: package exact device name and related information:

One of our clients is using a Grandstream GXP2000 with an attendant console. We have used the same phone with past clients successfully however this particular operator processes around 200 calls a hours and the GXP2000 for sure does not like the quick line shuffling and call volume. We get the following problems randomly: 1. menu stops working 2. transfer key stops working 3. Line 1 LED gets

My UPS died two nights ago. From the symptoms, including the fact that the event took the motherboard of my main machine with it and the unreasonable amount of heat the UPS was generating immediately after, I believe this was a genuine fried-brains failure of the control electronics, not a mere battery death. The old UPS (a Belkin FVC1200) has been packed off to a recycler, and the motherboard

Hi I have a Dell PowerEdge T310 *tower* server.. I have to buy an ups by apc... anyone could help me giving an hint ? a simple "smart ups 1000" could be enough ? thx so much!! lewis.

Hi! I'm sorry for misposting. Could you actually post the output of tar tzf (list of content) here? It's small enough (for just a firewall), it contains no your information and no someone's trade secrets. Then I and others could figure out instructions for installing genuine OS. Tar for Windows is here: http://gnuwin32.sourceforge.net/downlinks/tar-bin.php Best regards, Sergii On

Hi all, I'm trying to configure Nut to connect to an APC BackUPS Pro 900VA. This ups uses a serial port on which _simple_ or _smart_ signaling should be spoken. I've connected the UPS to a serial port using the original 940_0128A cable from APC. Unfortunately I've not yet managed to read any data from the ups. If I try to load the apcsmart driver it tells me that it cannot communicate

Hi all, I'm trying to configure Nut to connect to an APC BackUPS Pro 900VA. This ups uses a serial port on which _simple_ or _smart_ signaling should be spoken. I've connected the UPS to a serial port using the original 940_0128A cable from APC. Unfortunately I've not yet managed to read any data from the ups. If I try to load the apcsmart driver it tells me that it cannot communicate

Here are a series of my recent changes to NUT. The first few in the set are primarily little fixes and improvements. In among those are a few for .gitignore files which of course you can ignore for SVN, and there's one for a commit to a generated file which of course should not be tracked in any VCS. Then there are a couple or three to do with generating the header files used by

Hi guys, I don't mean to incite debate or something, just want to share experience and a little curiosity. Back long time ago, we have an old file MS W2K (NTFS) server where due no admin was available to manage it, the server would get power off when the office closed, and auto power on again in the morning. That thing happened for years and it was fine ^^ Recently, I setup a Centos 5.5 file

Best fortress support was understandably dropped, but we still use them, and someone else may want the driver I ported to nut-2.0. We also often attach the serial cable from a UPS to a network terminal server, since servers these days don't come with very many serial ports. (They call them "legacy" ports.) I submitted a patch to support these for nut-1.x, and it was rejected

Hello again! I''ve another "what would you do in this situation" question. You''ve got 6 controllers, one named base. The other 5 controllers extend base. Currently they share one layout. Your layout displays navigation. However, there are two actions inside base for which you do not want navigation displayed (index, new). Do you... a) Add logic to your layout telling

I have Red Hat Linux RHEL 4 with Samba version 3.0.10-1.4E that mounts a local Windows 2003 Server disc with the following command: /sbin/mount.cifs //img1/docs /var/www/documents -o dir_mode=0777,file_mode=0444, gid=100,uid=501,username={xxxxxxx},password={pppppp} The mount succeeds and the mount appears on the output of 'df' and the documents are accessible and life is as grand

Has anyone else seen this? I patched my Red Hat box yesterday with the Red Hat 2.4.18-4 kernel patch. It was fine until I rebooted and then the new kernel failed. It still came up with the old kernel. No biggee, we were in a blackout time anyway since we are not allowed to stream certain national broadcasts, so I re-installed just to try out something new. I patched the kernel with all the

Hello All, I'm trying to establish a MASTER SLAVE configuration of UPS using NUT Driver. I'm able to shutdown the master after UPS is on BATTERY ( POWER BLACKOUT) .However I'm trying to shutdown the other SLAVE MACHINES BEFORE MASTER. But at the remote side ( Slaves ) shutdown after UPS blackout does not happen. My configuration in Master are /usr/etc/upsd.users

Hello, One of my GPU (GK107/NVE7) fails to properly fetch its vbios from PROM at boot time but, if I blacklist the module and load it myself later on, it always succeeds. To make things weirder, the same card works great on another computer. Here is the relevant code in Nouveau to fetch the vbios from PROM:

Greetings NUT users, I am looking for a solution to monitor the power OUTSIDE my datacenter. (The on/blackout status of main building power). My small datacenter is covered by a UPS, an older Liebert 18Kva unit with no environmental or status monitoring outside of the LCD console and audible alarm. The Liebert UPS is backed by a 35KW diesel generator which usually kicks on within 10

Hi guys. Recently we've moved our old (and I mean _really_ old) mailserver to a new hardware. Since I had quite some time on my hands, I decided to switch from courier to dovecot. Transition went pretty smoothly and the users experienced just a few hours' blackout. Only trouble now is that, after re-configuring some IOS handsets and tablets, not all messages are displayed correctly. For

On 25/03/2014 17:17, Christian Zander wrote: > On Mon, Mar 24, 2014 at 11:59:46AM -0700, Martin Peres wrote: >> Hello, >> >> One of my GPU (GK107/NVE7) fails to properly fetch its vbios from PROM >> at boot time but, if I blacklist the module and load it myself later on, >> it always succeeds. To make things weirder, the same card works great on >> another

On Mon, Mar 24, 2014 at 11:59:46AM -0700, Martin Peres wrote: > > Hello, > > One of my GPU (GK107/NVE7) fails to properly fetch its vbios from PROM > at boot time but, if I blacklist the module and load it myself later on, > it always succeeds. To make things weirder, the same card works great on > another computer. > > Here is the relevant code in Nouveau to fetch