similar to: Monitoring second leg being dialed?

Hello list, this is my first post on this list. I have a server with Asterisk and a Linksys SPA3102 with 3 SIP phones. I have configured the SPA PSTN line as trunk to receive and send calls. I can call outside from SIP phone throw the PSTN line and all is OK, the problem is when I receive a call from the PSTN, on the out caller phone there is a demo playback. I want to redirect the call to a

I need another Sipura 3K and the replacement I think is Linksys SPA3102. Any input on how reliable is it? -- #Joseph GPG KeyID: ED0E1FB7

Dear all, I am from Saudi Arabiya and I am using digium hardware with asterisk 1.6. When I am executing following AMI originate API. Orginate start to execute extenstion without knowing of PSTN(FXO) channel is ringing. Any one can help me to resolve this issue ? Action: Originate Channel: Dahdi/g0/2923878 Context: outbound-ivr Exten: 1234 Priority: 1 ActionID: ABC45678901234567890

Hello I've never used Asterisk for a three-person call, and would like to check that MeetMe is the way to do this. The ADSL modem provided by my ISP offers free calls to landlines/cellphones when using a handset connected to an RJ11 port on the modem. A three-person call can be set up by using the standard PBX sequence: 1. Using the handset, call party #1 2. Hit "R" key on

Hello For customers who need a small IP PBX to handle up to four ISDN lines (in France, so I guess that means EuroISDN) instead of a PC + Asterisk and an ISDN gateway box, has someone already played with the Atcom IP-4B? www.atcom.cn/IP-BRIM.html Any feedback appreciated.

Hello, I'd like to run Asterisk on an embedded device, where space is scarce. It should be able to handle calls from a VoIP provider in SIP, calls from the PSTN through Dahdi, and voicemail. If someone's already done this, I'd like to know which directories/files are required for a basic install? Does this look right? ================= /bin/asterisk /etc/asterisk/ asterisk.conf

So made my first forray into 1.4 and DAHDI and hit a problem. (Not convinced this is a DAHDI issue though...) Testing an analogue line and asterisk sees the caller ID being passed, but then fails to detect ringing. A plain old analogue phone plugged in rings just fine. Console output: == Starting post polarity CID detection on channel 4 -- Starting simple switch on

Hy all, Recently a have a little problem with a Cisco device, SPA3102. I use this device with asterisk to dial out with outbound trunk. (SPA3102 has 1 FXO port) It working ok , but the device SPA3102 do this : when a call is placed for outgoing in asterisk and send to SPA3102 , this device "answer and dial the number in the same time" , in my CLI I see the channel is open , but on

Hello For users who 1) don't have a QoS-capable ADSL router and 2) would like to run Asterisk with a couple of SIP trunks, I was wondering what hardware is recommend to run any of the main open-source *WRT projects to which Asterisk has been ported: (http://en.wikipedia.org/wiki/List_of_wireless_router_firmware_projects Thank you.

Hi, I'm facing a strange problem. My setup is: Alice cellphone <--GSM--><--ISDN--> Asterisk <-- ISDN --><--GSM--> Bob cellphone When Alice calls Asterisk which forwards the incoming call to Bob, sometimes Bob sees Alice's number, sometimes he sees a default CallerID (which happens to match the dialed number and the ANI). For various reasons, Bob really needs to

Hello I need to write a script that will dial a list of customers and play a message. I couldn't find a way to tell Asterisk/Zaptel to wait until the callee has actually picked up the phone before proceeding with Playback(): ============ ;call made through Dial(): Doesn't proceed after off-hook/hangup [internal] exten => 8888,1,Dial(Zap/1/${IPPI}) exten => 8888,n,NoOp(We never

Hello all. I am just getting back into Asterisk and I am setting up my Linksys SPA3102. I have incoming calls working fine, as is the phone plugged into the unit. My problem is I cannot get the SPA3102 to dial a phone number automatically. I can call the extention of the PSTN and I get a second dialtone, and I can then manually dial. I'd like to be able to have Asterisk pass the

Hello List, I have found that asterisk supports only forwards in-dialog MESSAGE method. That is, if the MESSAGE method is sent within an active call. But according our requirement we need to send MESSAGE method to the other leg without being in a call (general stateless proxy forward). Is it possible to do this in asterisk using some tricks? Regards, Rajib Deka SIEMENS Ltd. Robert V Chandran

Hey guys! Can anyone help me figure out what causing this? I have the latest drivers installed. I tried Half Life 2: Episode One with the same settings, and it has no problems at all. Screenshot: http://img844.imageshack.us/img844/2375/hl21.jpg

Hello I'd like to install Asterisk and Dahdi on a Ubuntu host using packages instead of compiling from the source. Are the following packages enough for this? ========== asterisk - Open Source Private Branch Exchange (PBX) asterisk-config - Configuration files for Asterisk dahdi - utilities for using the DAHDI kernel modules dahdi-linux - DAHDI telephony interface - Linux userspace parts

I happened to be in the cli tonight as some (208.122.57.58) initiated a simple attack - just trying to make long distance calls from outside context. Although harmless, this went on for several minutes as the idiot just used up my bandwidth with SIP messages. Here's and example: [2011-12-28 22:53:42] NOTICE[9635]: chan_sip.c:14035 handle_request_invite: Call from '' to extension

Hello I need Asterisk (1.4.39.2) to simulate a flash hook (ie. hitting the "R" key on European handsets) so I can put a call on hold, dial a second number, and set up a conference call. By default, linux/include/dahdi/kernel.h sets the flashtime to 750ms, which appears to be too long for European telcos, as they seem to expect a line cut of about 100ms. After editing the

Hi! I try to get rid of some part of CALLERID(name) but I cant realy figure out a way to do it. For example: CALLERID(name) = "Martela (fax)" I am just looking for the part before ? (? in my case ?Martela?. I can?t serch for ? ?, could be many ? ?, but only one ? (?, thought i could do something like: exten => 0424449631,n,NoOp(${CUT(CALLERID(name),\(,1):0:-1}) But that gave me

Hello Some SOHO prospects only have a cellphone and I was wondering if someone had investigate running Asterisk on a smartphone, to perform tasks such as IVR, CID rewriting, voice-mail, notifications through e-mails, etc.? Thank you.

Hello I'd like to configure Asterisk so that... 1. I ring it from my cellphone with CID number displayed, just to notify Asterisk that I wish to make a call 2. Asterisk waits until I hang up, calls me back, and prompts me for the number I wish to call 3. Asterisk puts me on hold through Flash(), which is apparently the equivalent of hitting the R key on European handsets 4. Asterisk calls the