similar to: Configuring ISDN PRI using DAHDI

Greetings folks- I'm experiencing issues with a freshly installed box. When a call comes in via PRI (Sangoma AFT-A104), I see this in my logs: [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 12 (Invalid argument) [Dec 15 14:26:10] WARNING[23546] chan_dahdi.c: Unable to enable echo cancellation on channel 8 (Invalid argument) [Dec 15 14:26:10]

Trying to install wanpipe 3.5.18. No errors during compile. But when I reach the point where wanpipe and dahdi_cfg is started, I encountered an error. Starting WAN Router... Loading WAN drivers: wanpipe done. Starting up device: wanpipe1 wanconfig: WAN device wanpipe1 driver load failed !! : ioctl(wanpipe1,ROUTER_SETUP) failed: : 22 - Invalid

Hello All; Wanpipe is working only with sangoma cards so it does not work with digium cards? Also, who is better: to have echo canceler built in with the hardware or using olsec? Regards Bilal

Hi All; I have an E1 card with two ports for ISDN PRI. Do I need to install DAHDI in addition to LIBPRI? For placing outside calls (outgoing) via the PRI, then in the extension.exe file, I will use the Dial function? But how can I determine that I need to use the PRI channels and not the analoge channels? Last point: how can I know that asterisk is containing libpri? In other words, how can I

Hello List; Anyone can advise how realm authentication method is working? I mean, where to create the SIP username and password and where to create the realm that will be used for the authentication method for registration? Any help? Regards Bilal

Hi All; Is there an GUI for Asterisk that can help in showing the call flow (who is in progress, who is connected, called number, ...)? I was think in AsteriskNow does this? Any advise? Regards Bilal ____________________________________________________________________________________ Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now.

Hello all, I've got an intermittent issue with my asterisk set-up, and I'm pulling my hair out! Mostly everything works fine, but I get an error once every few days that sometimes (but not always) causes asterisk to stop accepting new calls and also stop responding to commands on the console (asterisk -r). The usual errors look something like this: [Feb 19 13:09:52] ERROR[18728]

Hey Guy, I have ubuntu 10.04 64bit and compiled dahdi / wanpipe 3.5.19 /asterisk-1.8.x I didn't understand what is the relation between wanpipe and dahdi ? do i need to start wanrouter service ? I am getting weird errors and my system got kernel panic many time when i restart dahdi service. any idea ? what is the startup sequence of all these service ? root at example:/etc/asterisk#

Sorry for re-posting, but the original one ended up inside a previous and unrelated thread. -- Matias ----- Hello, This simple SVD calculation (commands are copied immediately below) crashes on my Ubuntu machine (R 2.13.0). However it works fine on my Windows 7 machine, so I suspect there's a problem with (my?) Ubuntu and / or R. Can anybody else reproduce it (with Ubuntu 11.04)? Thanks

Hi everybody, since some time I am looking for a current and reliable solution to send and receive faxes (probably fax-2-mail and mail-2-fax) in conjunction with Asterisk. For testing I am using a HFC-ISDN passive PCI-card, in production a Digium Dual T1/E1 PCI-card will be used. I run CentOS 5.5 (Kernel 2.6.18) and Asterisk 1.4 (but I also can use 1.8) but did not find any solution where I

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi all! I'm testing a telephone connected to FXS port of a Sangoma A200 card. But I'm observing that callerid is not working. The configuration that I'm using in chan_dahdi.conf is the following one: - --------------------------------------------------------------------- ;autogenerated by /usr/sbin/wancfg_dahdi do not hand edit

Hi List; Asterisk does not have any kind of cards that can work with it to be used with Digital Phones (digital phones differ than analoge phone and differ than IP Phones). Anyone can advise about this as I did not find this on Diguim Regards Bilal Ghayad __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around

I'm trying to get my Sangoma B600 working with Asterisk 1.6.1 and DAHDI 2.2. I've tried running ./Setup dahdi (and with --64-bit_4GB flag, running amd64) and the compile fails with this for many versions of the driver (incl. 3.3.16, 3.3.16.22, and 3.4.1): Building modules, stage 2. MODPOST 1 modules CC /usr/src/wanpipe-3.3.16/patches/kdrivers/wanec/wanec.mod.o LD [M]

Hi List; I heared that IAX is good for NATing issues, but I do not know if it can help me in that senario: I have two Asterisks machines in different sites and both are behind NAT (both have private IP address), I need to link these two asterisks with IAX trunk (if it help really in such senario), but I do not know if it will work without doing special routing settings on the router (like

Hello, I'm experiencing some weird problems on my server: - 1) The following messages are filling up my logs: [Sep 29 08:24:59] WARNING[7077]: chan_dahdi.c:2789 pri_find_dchan: No D-channels available! Using Primary channel 140 as D-channel anyway! [Sep 29 08:24:59] WARNING[7078]: chan_dahdi.c:2789 pri_find_dchan: No D-channels available! Using Primary channel 171 as D-channel anyway!

Hi All; In dahdi: what we use instead of ztcfg -vv (that is existed /sbin/ztcfg -vv). ? Regards Bilal

Hi All; To download, compile and install DAHDI, do I need to download the both (dahdi-kernel and dahdi-tools) If yes, then do I need to do the compilation and installation command for each package? What is the method to download, compile and install the both packages as one package? By the way: Why there is dahdi-kernel and dahdi-tools? In other words, for what the kernel is used and for what

Hello, there has been a post to this list somewhere arount april which said that it is possible to use a Sangoma BRI A500 card with zaptel and asterisk bristuff. That is, without sangoma_brid and sangoma_mgd daemons and without woomera channels. Could anybody give me a short hint how to configure this? I tried wanpipe-driver + zaptel + asterisk-bristuffed, but I couldn't get zaptel to

Hi; How can I know the duration that the DAHDI channel is still used? I need to know its status and since when it is in this status, how? Also, is it possible to hangup the channel if it has been openned more than 90 minute? Other than using the timeout in the Dial command (because this I know it). What is happening with me that from time to time, I find some DAHDI channels are stayed connected

Hello; I am installing asterisk and dahdi on ubuntu "and I used my username bghayad to login for ubuntu and do the installation, actually I feel my problem is related to the?username and permission but I am not able how to fix it", I am facing now mainly the following two problems: The first one, asterisk is not starting automatically although I did sudo make config (for asterisk and