similar to: Asterisk 1.8.3: Started but no SIP talking

Hi All; When the call coming via the E1 dahdi and I handle the call (as first step) by exten => 5631040,1,Goto(OrangeCMG,s,1) it is not working and the call will be disconnected instead of queued. But, when I handle the call (as first step) by playing any sound file and then send for the queue, then it is working fine, WHY? exten => 5631040,1,Playback(WelcomeMessage) exten =>

Hi All; Again, the Cisco IP Phones 7942G and using Skinny: I upgraded the firmware to version 8.5 (skinny) and I am using skinny channel (chan_skinny) and the skinny.conf file. The phones are registering, but when we use them to place a call, we only hear tooooooooooo in the handset and we do not hear voice (even when we dial the digits, we only hear toooooooo .. but it dials and destination

Hi All; If I set a context other than the default context, then I do not see a generation for a configuration in the extensions_additional.conf for this context, but always the generation for the configuration is for the default context (from-internal). Normally, I have to put some Phones in a context and another Phones in a context, and give each context a privilages, but if I do this, then I

Hi All; Can anyone advise if using Cisco IP Phones in skinny protocol is fine or not? Or it is better to use it in SIP protocol? Regards Bilal

Hi All; Using the FreePBX, after I added the extension from the GUI, I discover that it is automatically added in the extensions_additional.conf in the context [ext-local] and [from-did-direct-ivr] How I can change these context name? I need to determine this. How? Regards Bilal

Dear Tariq; About elastix.org, this can be use with Asterisk or it is coming as a complete IP Telephony, Call Center, IVR and Reporting? Because, I do not need to install another IP Telephony on the server which already has asterisk which is an IP Telephony, this will cause a problem in the service (for example, when listening for SIP port of 5060).

Hi ALL, still having trouble getting Ast 12 to run. I got it compiled and built but now when I try to run, I'm getting a missing library error that seems to be in error (see below). The .so file DOES exist with correct permissions. [root at Asterisk12 ~]# asterisk -rvvv asterisk: error while loading shared libraries: libasteriskssl.so.1: cannot open shared object file: No such file or

I'm trying to decide if I need to open an issue for this or if it's just a misconfiguration issue of some sort. Here's the situation - yesterday morning, I downloaded asterisk 1.8.19.1 and installed it on a fresh CentOS 5.8 installation and got a shell of a basic asterisk install setup (minimum required configuration files, etc, with no dialplan or sip peers setup yet). In the

Hello; I need to use Cisco IP Phones with Asterisk and I have some questions to know how to use it if someone can advise: 1) How I can assign for each button an extension? 2) How I can assign for specific button a feature to be used (like call forward or call pickup .. etc)? 3) As you know that it is required to have a correct username and password to login, so where to give the username and

Hi All; I have an E1 card with two ports for ISDN PRI. Do I need to install DAHDI in addition to LIBPRI? For placing outside calls (outgoing) via the PRI, then in the extension.exe file, I will use the Dial function? But how can I determine that I need to use the PRI channels and not the analoge channels? Last point: how can I know that asterisk is containing libpri? In other words, how can I

Hi All; I do not know if anyone faced such case in dealing with open vpn (as we need it for fring to be used from the mobile: Which mobile can be used to install the open vpn client on it, so we can use it to do a vpn channel with the server that has open vpn server? Regards Bilal

Dear, I have asterisk 1.6.2.13 in a small hardware PBX (512 GB RAM and Celeron), and last days when I call from one extension to another of the same PBX after I dial the number the rings sound after 20 seconds. In the CLI log, when I debug the AGI, I see always goes good until dialparties.agi, and after that there are 20 seconds without any log, and so the ring sound. I've read

Hi List; I need to configure a softphone to be client and use it with Asterisk, which is the recommended one? Is it iax2? Regards Bilal ____________________________________________________________________________________ Boardwalk for $500? In 2007? Ha! Play Monopoly Here and Now (it's updated for today's economy) at Yahoo! Games.

Hi List; How can one Asterisk Box A to send a SIP call for another Asterisk Box B, and that call to be authorized based on the username and password, and not on the IP (as the IP address of the source is not known because it keep changing)? I think the trick in the Dial command, how to write it properly in a way that other Asterisk Box can recognize the sip username and password which are existed

Hello: We have a TDM2433E Digium Card (12 FXS, 12 FXO) and Asterisk 1.8.7.0 running. Everything seems to be ok but call transfers. This is the issue: *A, B, C and D are in FXS ports*. 1) A calls B. B anwers. 2) B tries to transfer the call to C dialing *2 (code for attended transfer). 3) A hears MOH. B dials number C. 4) Asterisk says the dialed number is incorrect or non existing. We tried

Hi All; Anyone knows if there is an Asterisk version that setup can be stored in Database instead of the configuration files (.conf)? Any advise? Regards Bilal

Hi Danny; Really I did not understand how I can determine if the IO will be DB or conf files? Is it from the Asterisk manager? Regards Bilal ------------------------- It depends on how you are configured. The gui interfaces using Asterisk Manager, so you get the Same IO from the gui that you would get from a native manager session. -----Original Message----- From: asterisk-users-bounces at

Hi; If my landline service provider does not provide the ability to send the SMS, and I need to send SMS from asterisk, then what is the required? How? Is it possible to send SMS from asterisk using SIM card to be connected via GSM adaptor connected to FXS ports? Or HOW?

Hi, I've been meaning to fix my non-working paging feature here for a while, and I've just spent the last 5 hours looking at many, many web pages that all say the same thing. I am using Asterisk 1.6.2.18 and Polycom phones, both older (501 with "latest" legacy 3.1.7 firmware) and newer (335 and 650 with latest 3.3.1f). I have changed the correct values in sip.cfg like

Hi All; I tried Firefly softphone with IAX and it gave very poor quality. Any one advise a good strong softphone that can work with IAX fine? Regards Bilal ____________________________________________________________________________________ Be a better friend, newshound, and know-it-all with Yahoo! Mobile. Try it now. http://mobile.yahoo.com/;_ylt=Ahu06i62sR8HDtDypao8Wcj9tAcJ