similar to: Asterisk-Asterisk E1 connection

Dear all, I have to install an E1 card in my Asterisk 1.4.23 server and here is my short question: Is it necessary to install or update any Asterisk/Zaptel/Any extra module or the default installation is good enough to just plug and run the E1 card ???? Thanks a lot Alejandro

Can't anyone stop self-promotion and tell the poor guy what he needs. A T1/E1 X-over cable using an RJ-45 (8-cond.) is pinned out as follows: 1 - 4 2 - 5 3 - NU 4 - 1 5 - 2 6 - NU 7 - NU 8 - NU NU = Not Used I have not in my experience seen any problems with using a Good Quality Cat5 vs. Cat 3 (telco standard) cable for X-connects. YMMV, but you should be fine. As far as the shielding

Dear, I have asterisk 1.6.2.13 in a small hardware PBX (512 GB RAM and Celeron), and last days when I call from one extension to another of the same PBX after I dial the number the rings sound after 20 seconds. In the CLI log, when I debug the AGI, I see always goes good until dialparties.agi, and after that there are 20 seconds without any log, and so the ring sound. I've read

Dear all, I have an Asterisk SIP server in a LAN environment and I want your opinion in order to decide the use of an audio codec: What audio codec is better, G.711a or G.711u ??? Which suites to my LAN voip calls ??? Thank you !!! Alejandro -------------- next part -------------- An HTML attachment was scrubbed... URL:

Dear all, I need to build a PBX based on Asterisk for a call center. I have worked with raw Asterisk but it's hard to work for big implementations think. Also I have worked with Trixbox CE for a small bussines and it was prette good, but I have not have many features like ACD. I know there is another version called Trixbox PRO -specially Call Center edition- that's not free but has got

Dear, I need to create a custom device extension in order to dial a local queue. Suppose my queue number is 8888, how can fill the Dial field from the custom extension ??? Because if I put just 8888 or Local/8888, I don't succeed. Thanks a lot

Dear, I always had one E1 card with one span, so I've never had any problem in set it up through /etc/dahdi/sustem.conf and /etc/asterisk/chan_dahdi.conf because I put span=1. But now I have a PBX with two E1 cards with 4 span (8 span in total). How do I have to define both card in system.conf and chan_dahdi.conf, and how do I have to refer each span to the corresponding card ??? Thanks a

I have used cross-connect wire from the spool to make T1 crossover cables with RJ45 ends. All that matters is that pin one goes to four and two goes to five on both ends. ________________________________ From: asterisk-users-bounces@lists.digium.com on behalf of Andrew Sent: Sat 4/22/2006 2:51 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: Pinouts for T1/E1

Dear, I have an Asterisk PBX with two E1 cards: Digium TE122 and Sangoma A101D. Sangoma card has SNMP support but Digium card has not, and also SNMP does't give me ral time information. Within CLI Asterisk I execute "dahdi show channels" but I don't get information about channels usage. What is the best way to have real time monitoring of E1 channels usage and status ???

I for one think it is a great idea to buy a book with hard earned money and wait a few days to a week just to get an answer to a question that is freely available on the internet immediately. Hard pressed to think of anything in the "book" that is not on with wiki with more up to date and useful information. -----Original Message----- From: Alexander Lopez

At Sangoma we do quite a lot of back-to back T1 and E1 connections. T1 is not a very fussy connection, as the baud rate is only about 750 kbps. In our experience, for error free communications you can use the following rules of thumb: Up to 50 ft: Flat patch cable Up to 500 ft: Ordinary twisted telephone cable Cat 5 may be overkill unless you are going hundreds of feet. David Yat Sin

I agree. I haven't had a problem using CAT-5, even for long runs, however it's not a real T-Carrier cable and I didn't know how old the PBX is. Paul >I have not in my experience seen any problems with using a Good Quality >Cat5 vs. Cat 3 (telco standard) cable for X-connects. YMMV, but you >should be fine. As far as the shielding goes, I use UTP cables and >Connectors

Hello Im from Denmark and i've just got my Digium TE405P. But i have some problems when i connect it to my E1 connection (ISDN30). My telco delivered a alcatel box witch have a G.703 120ohm (DB9 with a serial to rj45) and a 75ohm coax connection. I've tried to connect using the 120ohm with rj45 and a ordinary utp cable. But it dosent seem to work. I've tried several zaptel.conf

Dear all, I'll install Asterisk 1.4 in an IBM xSeries 226 server with four HD's available, using CentOS as the OS. What's the best RAID type recommendation ??? RAID 1 or RAID 5 ??? Regards Alejandro

Hi, Sorry for maybe not a very list related topic, but I have always been curious if there is information on how many Asterisk based PBXs are operating Worldwide? Thanks and hope the community will not reject my curiosity! :) Best Regards, Vallu Sevana Oy -------------- next part -------------- An HTML attachment was scrubbed... URL:

Dear, when I dial *30 in order to get instructions to blacklist an extension, Idon't get the menu but I get a new dial tone. What happen please ??? What can I do to solve this ??? Thanks a lot, Alejandro

Hello Samba folks, I thought you might be able to help me. I have 2 machines, 1 is FreeBSD, 1 is win95. They can't ping each other, but the bsd box comes up in Network Nieghborhood when Samba is active. What's going on? Is it not possible to ping a windows machine from a unix box? They are on the same hub via UTP. IPs are 192.168.1.x and netmasks are same (255.255.255.0).

Dear all, I have Asterisk 1.4 with SIP. I have a voicemail implemented with GSM sound files. The problem is I have IP phones Utopix HyperPhone 202 which support only G.729a/u and G.723.1 high/low, but not GSM. If I choose G.729A the "pass-throu" calls among users are OK, but Asterisk can't transcode GSM to G.729A in voicemail calls. My company doesn'y want to pay for a G.729

Dear all, I use Trixbox as my PBX. Until a couple of days I've installed a GSM Gateway to communicate with our three cellular phones: 15 64227777 15 64228888 15 64229999 The GSM Gateway has just one SIM. I use the Free PBX web interface in order to set up the route and trunk parameters: Trunk: ******* Name: SIM1 Peer details: host=10.10.1.2 (IP from GSM Gateway) port=5060 type=peer

Dear all, I've read that Asterisk supports only the G.729 A audio codec. I have several Grandstream IP phones with G.729 A/B codec implementation. Does G.729 A/B mean both version A and version B, or A/B is a new version different from A and B and it's not supported by Asterisk ??? Thanks a lot Alejandro