similar to: Problem routing call to fax machine on DAHDI FXSport

I am running Asterisk 1.6.2.17.2 with a Openvox A400 card with 2FXO/2FXS modules. I'm trying to set-up things to route analog fax calls from a FXO port to an analog fax machine on a FXS port on the same card. Outgoing faxes work just fine. But incoming faces are routed to the right DAHDI extension, but the call dropped right as the fax machine rings for the first time. The fax machine

The card you installed has FXO or FXS modules in it ????? are you getting your lines directly from the telco co??? Doug D On Mon 23/08/10 8:37 AM , Cassius Smith cassius at cassius.org sent: * -----Original Message----- * From: Todd Reese * Reply-to: Asterisk Users Mailing List - Non-Commercial Discussion * To: asterisk-users at lists.digium.com [3] * Subject: [asterisk-users] Dahdi

I am having problems getting a Nicherons TDM400P wildcard clone to dial out. Everything appears to be configured correctly, but although I see call progress, it never seems to actually pick up the phone. (The following is a test of 911 emergency, where I substitute 811 [repair service] as the actual number dialed.) *CLI> -- Executing [911 at from-internal:1]

I keep getting a red alarm when trying to setup asterisk to use my TE420B EC. I only have a blank context setup in my extensions.conf as I haven't started to config that until I can clear this red alarm. I don't have physical access to the server, so I can't go reseat the modules/card/ethernet cable, though I have hands on location that have done this a couple times

Hello, My first attempt to get dahdi running on 1.4.28... with a Rhino 8 port modular card and a single FXS module. Got the Rhino card installed and the machine sees it: root at pbx:/etc/dahdi# dmesg | grep rcbfx [ 71.985309] rcbfx 0000:04:00.0: PCI INT A -> GSI 21 (level, low) -> IRQ 21 [ 71.985440] rcbfx 1: Rhino PCI BAR0 50100000 IOMem mapped at ffffc90008d7c000 [ 71.985504]

Hi, Running 1.4.26.1 here. I have installed TE420B card in my server, and followed the appropriate steps (as far as I know to configure it). This TE420B is connected to a CLEC (T1s), so I am using pri_cpe as singalling type. When I dial out, I get this message: Dec 4 11:37:31] WARNING[27983]: app_dial.c:1275 dial_exec_full: Unable to create channel of type 'DAHDI' (cause 0

Dear All; I am afraid from IRQ misses: 1 The ISDN E1 was working fine on the machine, the electrical disconnected and then the Red Allarm. I checked the dahdi and I found that I have to reinstall dahdi again and I did. But still not becoming UP. The output of the cat /proc/dahdi/1 is following (I am afraid from the IRQ misses: 1, so if it is a problem what is the solution)? [root at CC

Some recent issues I had with hardware seem to come back to not understanding two very similarly named files: /etc/asterisk/dahdi-channels.conf /etc/asterisk/chan_dahdi.conf I've modified the chan_dahdi.conf to work now, but it would appear all I needed to do was include dahdi-channels.conf in chan_dahdi.conf and the problem would not have persisted? Is it me or is that a bit Monty Python?

Hello, I'm facing problem where as whenever there are incoming call from pstn, there will be no audio coming in. User at the other end also could not hear my voice. This happens few days back. Im using asterisk 1.6.1.2 with dahdi tool 2.2.0. I thought it was time to upgrade, so upgraded to dahdi 2.2.1 and asterisk 1.6.2.5. However, it does not help at all. My current config as follows :-

We fairly recently switched service providers for our 4 PRI circuits. Since that time, we started to notice some failed inbound calls. These calls terminate with an ISDN cause code 47 'resource unavailble'. Most of the time I see this error on the first or second channel on the second span in a trunk group (This is the providers trunk group for hunting, not an Asterisk trunk group). All

# Span 1 span=1,1,0,esf,b8zs bchan=1-23 dchan=24 echocanceller=mg2,1-23 # Span 2 span=2,2,0,esf,b8zs bchan=25-47 dchan=48 echocanceller=mg2,25-47 # Span 3 span=3,3,0,esf,b8zs bchan=49-71 dchan=72 echocanceller=mg2,49-71 # Span 4 span=4,4,0,esf,b8zs bchan=73-95 dchan=96 echocanceller=mg2,73-95 # Global loadzone = us defaultzone = us Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1"

Hi, I've searched and searched on the possible problems. If anyone can help me that would be great. Span 1: TE2/0/1 "T2XXP (PCI) Card 0 Span 1" (MASTER) B8ZS/ESF CRC4 error count: 4750 E-bit error count: 5023 Timing slips: 72 1 TE2/0/1/1 Clear (In use) (SWEC: MG2) 2 TE2/0/1/2 Clear (In use) (SWEC: MG2) 3 TE2/0/1/3 Clear (In

Hi, I have just set up Asterisk to use an E1 line with a Digium card. And I can call both in and out, but my outgoing line is all ways identifying itself as the same number, and i can't even change it to another number in the same number series. Do anyone have some clue on how to fix this. I'm using Asterisk 1.6.2.13, libpri 1.4.11.4 and DAHDI 2.4.0. /etc/dahdi/system.conf:

Can anyone describe the asterisk implementation of this any better than the sample config files do? from zapata.conf ; Trunk groups are used for NFAS or GR-303 connections. ; ; Group: Defines a trunk group. ; group => <trunkgroup>,<dchannel>[,<backup1>...] ; ; trunkgroup is the numerical trunk group to create ; dchannel is the zap channel which will

Hello gang, We just got MaBell to turn on our callerid. I tested the capability with a southwest bell box and a plain phone, so I know the line is sending the signal. I'm running Asterisk SVN-branch-1.4-r204834 using a TDM400P card. Here is my dahdi_cfg -vv output: dahdi_cfg -vv DAHDI Tools Version - 2.1.0.2 DAHDI Version: 2.1.0.3 Echo Canceller(s): MG2

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

dahdi_cfg -vvv error `cut: '/sys/bus/dahdi_devices/devices/pci:0000:01:00.0/spantype': No such file or directory` PRI show spans --command not found test call not working. -- dahdi_genconf -vvv Default parameters from /etc/dahdi/genconf_parameters Generating /etc/dahdi/assigned-spans.conf cut: '/sys/bus/dahdi_devices/devices/pci:0000:01:00.0/spantype': No such file or

Hi list, Ive got a server with 6 ports on it (4+2 port card) we have a DS3 delivering all voice DS1's to us. Carrier has a trunkgroup for the first 8 span (we only have the first 6 plugged in right now). Everything works fine until we fail the primary D channel (D's are on 24,48) the secondary then picks up and outbound calls do not work, if we reboot Asterisk the D on 48 comes up and it

after installing asterisk 1.4.23.1 and dahdi-linux-2.1.0.4 and at CLI> module load chan_dahdi.so receive the following: signalling must be specified before any channels are. CLI> Warning [4663]: chan_dahdi.c:11627 process_dahdi: Ignoring signalling Error[4663]: chan_dahdi.c:10946 build_channels: Unable to reconfigure channel '1' Error[4663]:

We have integrated an Asterisk (TE110P) and a Mitel SX200. We usually get over 500 frame errors and over a 500 slip errors per hour. When the errors reach 1000 per hour the Mitel will take it's T1 card offline. At that point no calls can be routed from the Asterisk server to the Mitel and the TE110P reports a Yellow alarm. What can be causing all these Frame and Slip errors? We have been