similar to: Include ${HANGUPCAUSE} in CDR

Ok I can't get my CDR values to set from the h extension in either 1.6.2 or 1.8 What is wrong? Here is what I found in the cdr.conf ; Normally, CDR's are not closed out until after all extensions are finished ; executing. By enabling this option, the CDR will be ended before executing ; the "h" extension so that CDR values such as "end" and "billsec" may

Hopefully I'm not just missing some little detail here. We're trying to set the HANGUPCAUSE on SIP channels to have our softswitch play the proper recording instead of answering the call on Asterisk to play the message. It appears that no matter what the HANGUPCAUSE is set to, Asterisk always just sends "603 Declined". I looked through the source code briefly and it appears

Thanks Dovid! Indeed looks a bug but regardless of this, this problem made me think that the HANGUPCAUSE could be used for this purpose with benefits. I couldn't find an explanation about when DIALSTATUS would actually be better. The HANGUPCAUSE was reworked in version 11 ( https://wiki.asterisk.org/wiki/display/AST/Hangup+Cause) but I didn't find someone actually stating it is a better

Hi, I am using Asterisk: 1.6.1.20 LibPRI: 1.4.11.4 DAHDI: 2.3.0.1 Echo Canceller: MG2 Wanpipe-Driver: 3.5.15 Sangoma-Firmware: 43 (A104d) I handle some calls with my own PHP-AGI-Script. After a dial-command I use "GET FULL VARIABLE ${answeredtime}" or "GET FULL VARIABLE ${dialstatus}" and get valid information. Sometimes "dialstatus" has the value

Hi, I have the following code that operates when a channel is hung-up: [record-hangupcause]exten => 1,n,Set(CDR(hangupcause)=${HANGUPCAUSE})exten => s,n,Return() Before the dial a hangup handler is registered: Set(CHANNEL(hangup_handler_push)=record-hangupcause,s,1) The routine is called and the variables are being set, however not on the channel's CDR which made the call. I believe this

Hello list, Hope all doing well! I've been checking some cases when a Dial fails and dialplan execution continues to handle this. I am finding it a little confusing how we should handle the DIALSTATUS and the HANGUPCAUSE in this situation.... More specifically, I am facing a case in version 13.6.0 where I am getting a DIALSTATUS=BUSY and HANGUPCAUSE=19 after receiving a 480 SIP error. Seems

Today I get the remark that a call got disconnected after 10 minutes. This what my VERBOSE-logfile tells me : [May 18 15:36:30] VERBOSE[3940] logger.c: -- Executing [00493516426 at intern:1] NoOp("SIP/51-b76023b8", "Gesprek naar GSM-nummer via Telenet") in new stack [May 18 15:36:30] VERBOSE[3940] logger.c: -- Executing [00493516426 at intern:2]

Hi, I've been debuging the call disconnection problem in our architecture: PSTN---E1---OldPBX---E1---Asterisk This is our problem: -SIP user agent "A" calls a pstn phone "B". -"B" hangs up the call. -SIP user agent "A" starts listenning busytones... But the call still on. (and being payed). - Call only ends when it is correctly hanged up in the

This was always possible in the past, however does not work in the current release. I believe this is a bug. To: asterisk-users at lists.digium.com From: cervajs at fpf.slu.cz Date: Fri, 9 Oct 2015 10:04:47 +0200 Subject: Re: [asterisk-users] Storing HANGUPCAUSE in CDR search in archives save the records to another table like cdr_extended Dne

Managed to implement this on asterisk v1.4.24.1, Also, Hangupcause updating to user field. However, this only works on the edge of my voice network (demarcation point) It does not work on my internal routing boxes as I use IAX to route between remote sites. I was thinking of using some sort of SIP variables to transport these results over the IAX trunk.. Any bright ideas folks???

Hi, I'm using Asterisk and a TE110P E1 PRI in Chile. When I call to a disconnected number or any not operational number, the telco sends the Hangupcause disconnection code and an audio message notifying the disconnection cause to the user. Asterisk does not allow the user to hear the audio message form the telco, instead it cuts the call. Any other legacies PRI PBX I've tested allow

On Wed, Mar 25, 2015 at 7:35 AM, Salaheddine Elharit <salah.elharit200 at gmail.com> wrote: > hello list, > > i have asterisk 11.15.0 and i have some trunks sip from my provider > > we have some ip phone astra 6731i > > each Ip-phone is configured with trunk and we call > > no ihave configured another trunk from the same provider in my asterisk > > i can call

Hi, Is there any way to tell Asterisk not to generate additional headers like: X-Asterisk-HangupCause: Normal Clearing X-Asterisk-HangupCauseCode: 16 I can't find any relevant option in sip.conf file :-( Thanks for help. Chris

Hello, On your BRI or PRI's what do you guys get as HANGUPCAUSE when dialing an unalocated number? I always get 3 (no route) which is less than helpful.

Hi, I'm trying to get HANGUPCAUSE on my cdr the problem I'm facing is that this option: endbeforehexten=yes is not working at least on asterisk 1.6.0.1, so if I put yes o no I cant set CDR value with that value. It seems to finish the CDR record before h is executed. I'm using cdr_mysql. Any idea?? Thanks!! -------------- next part -------------- An HTML

What would be the best way to solve this problem? Anyone else that have got the same problem with Android’s native SIP client, especially on Samsung phones? I do not know if the bug is in Android native SIP, or Samsung’s build of the SIP client, or if the bug is even with the OpenVPN client, or where the bug actually is. The ACK might even be sent for real, but have the incorrect source IP so

I'd like to grab the SIP response code that comes back from an INVITE. The HANGUPCAUSE gives the converted ISDN cause code. Anyone know of a way to get the SIP response code instead? Doug. __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com -------------- next part -------------- An HTML

tnaks for your response but the number dialed exist and i can call this number when i configure the trunk directly in x-lite and i call call also this number from my cell phone . any help thanks and regards 2015-03-25 12:59 GMT+00:00 Matthew Jordan <mjordan at digium.com>: > On Wed, Mar 25, 2015 at 7:35 AM, Salaheddine Elharit > <salah.elharit200 at gmail.com> wrote: > >

Hello. I have a problem with the native Android SIP client, not acknowledging the call. Sent a message to the list for some weeks ago containing a sip debug log, but it only got stuck in moderation queue due to too large size (and it said I would get a message if moderators rejected it, but did not get message and I don't think it got posted to list either) This ONLY happens when

hello list, i have asterisk 11.15.0 and i have some trunks sip from my provider we have some ip phone astra 6731i each Ip-phone is configured with trunk and we call no ihave configured another trunk from the same provider in my asterisk i can call all numbers just the numbers are configured in thses ip phones. but when i configured the same trunk in x-lite i can call theses ip-phones without