similar to: minimum card for dahdi timing source ?

Hello there: I think I have a silly kernel configuration problem. I'm running: * vanilla 2.6.27.10 kernel built from source * dahdi-2.1.0.4 built from source So far so good, dahdi module loads just fine: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.1.0.4 when I try to: hal04 dahdi # modprobe dahdi_dummy FATAL: Error inserting dahdi_dummy

Hello all, Ok it is Sunday afternoon and I am going crazy. I have been running in circles so long that I can't think straight. As an example, I sent this message to the wrong address the first try, AAARRRRGGGGGGHHHHH. I have Asterisk 1.6.0.6 and DAHDI Tools Version - 2.1.0.2, DAHDI Version: 2.1.0.4, OpenSuSE 10.3 x86_64, tdm422 at the end of installing dahdi-linux and dahdi-tools I get:

Hi. I have a Debian Leni system with asterisk-1.8. I was trying to get meetme to work and it depends on dahdi, so I compiled dahdi-trunk and dahdi-tools-trunk, however, when trying to insert dahdi_dummy, it complained about symbol crc_ccitt_table, although the module was actually there in the kernel tree. So, I took the Debian source, and I had the config and I did make Bzimage, make modules

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.1 DAHDI-Linux 2.5.1 DAHDI-Tools 2.6.1 DAHDI-Tools 2.5.1 DAHDI-Linux-Complete 2.6.1+2.6.1 DAHDI-Linux-Complete 2.5.1+2.5.1 These releases are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools

The Asterisk Development Team has announced the releases of: DAHDI-Linux 2.6.1 DAHDI-Linux 2.5.1 DAHDI-Tools 2.6.1 DAHDI-Tools 2.5.1 DAHDI-Linux-Complete 2.6.1+2.6.1 DAHDI-Linux-Complete 2.5.1+2.5.1 These releases are available for immediate download at: http://downloads.asterisk.org/pub/telephony/dahdi-linux http://downloads.asterisk.org/pub/telephony/dahdi-tools

I'm playing around with an ALIX 2D2 board (http://www.pcengines.ch/alix2d2.htm). It's a fanless, x86 system using an AMD Geode processor with 256MB of RAM. Also available are two network interfaces, two USB ports and one serial port (no keyboard or VGA). I'm using the Voyage Linux distro, which basically is Debian Lenny optimized for this board. Asterisk 1.6.1.12 runs fine on the

Hi, I have some servers that are dedicated to do meetme conferencing. From some previous test i concluded that I need to use dahdi_dummy as it is more accurate. If I did use the core timers in dahdi (not loading dahdi_dummy) I got bad quality in the conferences and dahdi_test showed 99.6% as worst. I thought maybe the issue as bad hardware for the timing or something else. But today I

Aloha, I'm not sure why I'm getting this error, but I can't seem to get chan_dahdi to load. SIP & IAX2 are working fine. Debian 4 w/ 2.6.28 kernel. Asterisk 1.6.1.5, dahdi-linux 2.2.0.2, dahdi-tools-2.2.0 CLI> module load chan_dahdi.so Unable to load module chan_dahdi.so Command 'module load chan_dahdi.so' failed. [Sep 1 10:57:51] WARNING[31696]: pbx.c:4550

Hello list, I'm experiencing a lot of server freezes lately. The server just... freezes. I notice in the log files (/var/log/asterisk/messages & /var/log/messages) that logging stops at the time the server hangs. Logging continues when the server has been restarted (which is the only solution). So it is not a proces that hangs, it's the entire server (CentOS5.5 + Asterisk +

Hi, I need to run ztdummy for Paging, but now that this is all become dahdi I don`t really know where to start. I did build dahdi before building asterisk, but that`s it. I find it hard to find any documentation referring to dadhi instead of zaptel. I have no Digium hardware, but I still need the ztdummy timer (or whatever it`s called now). How do I get myself going? Regards,

Hi to all. I'm trying to use meetme on asterisk 1.4.22.1. On a debian i've compiled (as i need h323 support) openh323_v1_18_0 pwlib_v1_10_0 dahdi-linux-2.1.0.3 dahdi-tools-2.1.0.2 asterisk-1.4.22.1 All works fine, dahdi status is: asterik:/data/programmi# /etc/init.d/dahdi status ### Span 1: DAHDI_DUMMY/1 "DAHDI_DUMMY/1 (source: RTC) 1" (MASTER) asterik:/data/programmi#

Howdy, I am playing around with asterisk within an LXC container on Ubuntu 11.04. I have asterisk (1.4.42) running fine, but want access to dahdi_dummy for timing (meetme). I have dahdi installed on the "host", and dahdi_dummy is loaded: root at astnorth:/# ls -ltr /dev/dahdi total 0 crw-rw---- 1 root root 196, 250 2011-06-08 13:59 transcode crw-rw---- 1 root root 196, 253

I am installing dahdi on a machine lspci 00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge 00:01.0 PCI bridge: Hewlett-Packard Company Unknown device 9602 00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0) 00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1) 00:06.0 PCI bridge: Advanced Micro Devices [AMD]

Dear all, i have a problem with a system running - Ubuntu 10.04 ( all updates done ) - ii asterisk 1:1.8.5.0-1digium1~lucid Open Source Private Branch Exchange (PBX) - ii asterisk-dahdi 1:1.8.5.0-1digium1~lucid DAHDI devices support for the Asterisk PBX I also use freepbx 2.9 for the configuration. Hardware is a Dell R410 and a Digium

I have a TDM400. Just updated Fedora 12 to kernel 2.6.32. Rebuilt and installed dahdi-2.2.1. kernel modules loaded. lsmod | grep wctdm wctdm 37233 0 dahdi 194985 1 wctdm lsmod | grep dahdi dahdi 194985 1 wctdm crc_ccitt 1549 2 dahdi,isdnhdlc dmesg: dahdi: Telephony Interface Registered on major 196 dahdi: Version: 2.2.1

Hello I was editing files manually, and noticed that if I include the familiar "fxsks=1" in /etc/dahdi/system.conf, Dahdi fails loading: ===================== # cat /etc/dahdi/system.conf loadzone = fr defaultzone = fr fxsks=1 ===================== # /etc/init.d/dahdi start Loading DAHDI hardware modules: wctdm: [ OK ] /usr/share/dahdi/waitfor_xpds: Missing

Hi I am in the process of installing a new box and using dahdi. I have a tdm410 + hardware echo canceller. I have just read in the read me for dadhi that VPMADT032 support has been removed and unlike with the zaptel stuff i could just download and install the firmware I can't with dahdi what is the best way forward to recompile with hardware echo canceller support. Thanks Alex

Greetings, Because of the heavy load and the high expectations of an asterisk server offered as a solution integrated with our CRM software.. we were looking into other possibilities than software Licenses for G729 and G723 codecs.. to lower the pressure on the processor giving it more space to do more work. We heard of a hardware (PCI CARDS) can be used with Asterisk that does the work. And we

Hi, I am running Fedora 7 VM. On an earlier configuration with zaptel and Asterisk 1.4.21 , meetme worked alright. I upgraded to Dahdi and Asterisk 1.4.26, and the result is choppy sound via Meeme, while a simple Musiconhold works OK with descent audio quality. So I am sure its a Dahdi_dummy problem. Running dahdi_test gave me very poor results. Opened pseudo dahdi interface, measuring

Hello Friends, I am trying to Installl dahdi on amazon EC2 which have Open-SUSE-11.1 X86 version. and here is snap of uname- a command *Linux ip-10-160-86-41 2.6.32.19-0.3-ec2 #1 SMP 2010-09-17 20:28:21 +0200 x86_64 x86_64 x86_64 GNU/Linux* when I try to run DAHDI distribution dahdi-linux-2.1.0.4 I am getting following error *echo "You do not appear to have the sources for the