similar to: debian/dahdi/zaphfc - Unable to receive TEI fromnetwork!

Hello, The harddisk of my etch/bristuffed asterisk1.2 box finally died. I moved the cheap (1397:2bd0) HFC-S card to a squeeze host (i686) and built dahdi modules 2.3.0.1 using m-a. After zaptel->dahdi and asterisk 1.2->1.6 config adaptations, everything seems ok, except for the BRI side, unable to bring layers 1/2 up. Asterisk reports: chan_dahdi.c:12393 dahdi_pri_error: 1 Unable to

Hello, Is it possible, for testing, to connect an cat5 straight patch cord between 2 ports of a Digium B410P card and use these 2 ports as a normal dahdi trunk ? I've tried this: One port is set as NT, the other as TE. I would expect timing to come for system hardware so I choose in /etc/dahdi/system.conf : span=1,0,0,ccs,ami span=2,0,0,ccs,ami Results: - both ports lights are green -

Hi, I'm experiencing difficulties to get a B410P running with Asterisk 10.3.1 and DAHDI 2.6.1. Am I supposed to use DAHDI for this card and ISDN BRI for my country (Belgium)? thx, BC

Hi. I'm running some asterisk boxes on different sites, some equipped with a couple of ZapHFC cards, others with Junghanns quadBRI cards. All boxes were compiled with Asterisk 1.2.10 (libpri 1.2.3 zaptel 1.2.6) and bristuff 0.3.0 pre 1s, distribution is Fedora Core 4 with kernel 2.6.17.3 The cards are connected to Telecom Italia's NT1/NT1+ S/T lines; some of them are point-to-point,

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

Hi all, I really hope that you guys can help, because I've been tearing my hair out for the past 5 hours on this one. I have a Zaphfc (BRI) card in TE mode connected to the S-Bus of a Nortel Meridian phone system. Phone calls from the Nortel to say MSN 510 are correctly being sent to the right SIP phone. When asterisk dials say Zap/g2/224 (a Nortel internal extension) the call goes

I have a "Cologne Chip Designs GmbH ISDN network controller" in my asterisk box, and an ISDN line connected up to it. I downloaded the bri-stuff 0.1.0-RC4a package from junghanns.net and used that to compile asterisk using these instructions: http://www.voip-info.org/tiki-index.php?page=Asterisk%20zaphfc%20install When I try to call my asterisk box, my sip phone rings twice and then the

I've got some weird behavior on my HFC-s cards. asterisk CVS-06/26/04-21:28:35, bristuff 0.02, libpri 20040510, zaptel 20040623 When i pick up my ISDN phone on Zap5-1 ("3987") and call the external number "1901" it will do so, connect me and everything is fine. In the second, where it tries to attempt the native bridge, the audio will disappear. Using another card

Hi, I have a partial working installation with zaphfc. Incoming call : For incoming call, seems work fine. But the sound is very bad with bounce short crashing sound. Same sound with echo cancel off or on. SDA work fine. Another problem, it's seems that's zaphfc don't reset correctly the line. I have one of my D channel how was busy even after stop communication. Outgoing call :

Hi all, So, we reverted the LibPRI version and tested it, and then tried with the latest version of everything. Still no changes. The BRI line is in PTMP. If we set the configs to PTMP in the genconf_parameters and try it, we get the following: [Jan 21 17:32:20] ERROR[20341]: chan_dahdi.c:12645 dahdi_pri_error: Unable to receive TEI from network! If we set it to PTP (which it is not) we

Hi! Has anybody seen anything like this using zaphfc? On outgoing calls (via isdn) , the line gets hung-up as soon as the called party answers. As seen below i get some protocol error (6) - but i'm not sure if this is related to the "hang-up" which apparently comes a little earlier?! Incomming calls on the isdn (zaphfc) interface is working just fine (P.S. what about the

Hi, I've been learning asterisk for a couple of weeks now - and it worked for me as faar as standard configurations where concerned (sip/iax outbound/isdn4linux & capi with AVM Fritz!, Digium X100P FXO). Now I recently I'evaluating to use asterisk as a replacemnt for our companies (15 employees) legacy pbx system and I'm experiencing multiple problems with the hfc isdn cards:

I tried to setup an PBX System with the following parties: 1. SIP Phones 2. One AVM ISDN Card with CHAN_CAPI for Outbound dialing and receiving external calls 3. One HFC-S PCI Card in NT-Mode with ZapHfc for physical ISDN Phones. 1+2 work perfect I have problems with part 3 Card is working, drivers loading fine, asterisk initializes chan_zap without problems. Demo did work. My problem is

hello, I have a asterisk box (Slackware 9.1.0, Linux 2.4.31) connected to a Ericsson Businessphone PBX on the internal S0 bus with HFC-S card and zaphfc driver - point2point mode -. --------- | TELCO | | BRI | --------- | | PBX external S0 -------- | PBX | -------- | PBX internal P2P S0 NT Mode | | HFC-S Card P2P TE Mode

Hello all, if I try to call from one phone on the internal S0 to another on the same S0 using zaphfc, the bus is hung up. The called phone is ringing, but I can't talk from one phone to the other. The error I get is: -- Executing Dial("Zap/2-1", "ZAP/1/55|15|tr") in new stack -- Requested transfer capability: 0x00 - SPEECH -- Called 1/55 -- Channel 0/1,

bri-stuff.0.1.0-RC4a on debian sid with 2.6.7 kernel isdn sk: Bus 0, device 18, function 0: Network controller: Digi International Datafire Micro V (Europe) (rev 2). IRQ 17. Master Capable. Latency=16. Max Lat=16. I/O at 0xe400 [0xe407]. Non-prefetchable 32 bit memory at 0xd8021000 [0xd80210ff]. i still receive error messages continuosly (every few seconds) i

I've a lot af this waring May 12 18:44:35 WARNING[65541]: chan_zap.c:6070 zt_pri_error: PRI: received TEI check request for TEI = 76 May 12 18:44:36 WARNING[65541]: chan_zap.c:6070 zt_pri_error: PRI: !! Got a UA, but i'm in state 1 May 12 18:44:42 WARNING[65541]: chan_zap.c:6070 zt_pri_error: PRI: received TEI check request for TEI = 76 How i can resolve it? Thak's Tiziano

Hello List, is someone operating a DID /P2P / Anlagenanschluss with more than one HFC-Based ISDN-Card ??? I have now 12 hours of setup-troubles behind me with Colt-Telekom, where we did not get it working with two HFC-based cards. Here the setup: - 2 HFC-ISDN-Cards (the one from Conrad-Electronic) - bri-stuff.0.0.2 (with the asterisk-sources from the download.sh-skript) - two NTBAs from

I am running Asterisk 1.0.9 and the latest bristuff in combination with a HFC isdn card, connected to a BRI interface. For some reason, I am not able to have it dial out (see below). It exits with DIALSTATUS=CHANUNAVAIL. One thing that may be misconfigured is that it says: Signalling Type: PRI Signalling. How do I change this? Or is this the correct value? I posted my configs below. ------