similar to: ISDN - Busy signal on 3rd call

hi i've configured a Beronet BN8S0 Card with misdn beronet utility. the card is configured with all lines in TE and P2P mode, and it is connected with the special cable with an ISDN connection. i've turned on debugging to level 4, this is the output from the asterisk cli when i receive a call: P[ 5] MGMT: Short status dinfo 1000001 P[ 5] MGMT: SSTATUS: L1_ACTIVATED P[ 5] handle_frm:

Use Set(CALLERID(num)=9999999999) instead of using CALLERID(all). Remember to set this BEFORE you Dial. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 12:36 -->> To: asterisk-users at lists.digium.com -->>

You're quite right. We'll need to see your misdn.conf file to check the settings. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 13:49 -->> To: asterisk-users at lists.digium.com -->> Subject:

Hello everyone. I've got this really annoying HFC Cologne card (or however I should call it - a single channel ISDN card based on the HFC chipset). It wrongfully detects lots and lots and lots of incoming DTMFs, to the point the card is not usable. Here's a sample out of CLI: P[ 1] I IND :DTMF_TONE oad:206361 dad:520101 P[ 1] --> mode:TE cause:16 ocause:16 rad: cad: P[ 1] -->

I am trying to use misdn insted of zaphfc to drive two billion isdn cards zaphfc is ok, but the problem with cdr and the fact tha you always have to wait the bristuffed version of asterisk took me to try another way. so I downloaded the misdn installation script from beronet for the last version ( I am using asterisk stable 1.2, so now is 1.2.5) wget

Hi, Hi All, I've just delved into the world of asterisk and I'm having a few dtmf issues. Internally, amongst sip phones, dtmf is fine. Externally, if you ring from a GSM mobile, DTMF is fine, however if you ring from a standard phone, DTMF fails to register. I am attempting to use a quad port HFC-4S Beronet Card. I've been searching the web most of the last week and

I hadn't used FWD for quite a while. A customer sent me an email last week, "Is FWD broken when one tries to use it with IAX?" I have been playing around, and indeed seems to be the case. Is there anyone out there successfully using the two of them together? Thanks. B. -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be

i am using asterisk 1.6.2 with mISDN and a passive AVM Fritz!card on CentOS 5.5. The only thing, i want to do is a call-redirection from an isdn-call to my mobile via sip-account. My extension conf is: general] static=yes writeprotect=no [globals] OUT_PORT=1 [ISDN] exten => 12345,1,Dial(SIP/012346737222 at sipprovider.local) If i call to the msn 12345, the SIP-call is going out, but after

Hi, Since a week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) ->

Hello list, I've been having a problem for some time now that I can't figure out how to solve it. On a PTP BRI ISDN line, if I have both channels in use and I place a third call from the outside, I'm not getting a busy tone like I should. Instead I get a congestion tone, as if the line was not working/didn't exist. Currently I'm using mISDN 1_1_9.1 and Asterisk 1.4.35 with

Hi. I'm running Asterisk server with 10 sip phones, and 2 grouped T0 lines with 10 DDI numbers. My provider is France Telecom and my setup is : - Debian Lenny - Asterisk 1.4 - Linux kernel 2.6.25.17 - mISDN 1.1.8 driver - Sip phones Thomson ST2030 No problem with the SIP . But when reveiving a call on RNIS line (any of the DDI numbers), the associated SIP phone rings indicating _two_

I'm running a setup with chan_misdn on a austrian PTP-line. When somebody dials in without an extension, he gets a busy signal. I don't see the call at all in asterisk. I *have* set immediate=yes in misdn.conf. And I *do* have an s-extension in my dialplan for the context used by misdn. Calls that provide an extension work fine. Attached is my misdn.conf and a verbose 3, misdn set debug

Hi all I have a very strange problem here... I use a hfc-s card with mISDN in NT mode with an ISDN Phone connected. When I make a call, the phone rings two or three times and then misdn runs into a timeout... I don't know where to set that timeout, but it's way to short for the called to pick up the phone. If the destination phone is picked up, then everything is allright and the

I'm trying to set caller ids on outgoing calls. I have a quad BRI B410P card connected to my telephony provider. I know the list of DID numbers the provider assigned to my company. If I don't set the caller id then the callee always sees the same "top-level" number. If I set the caller id to a specific DID number we own, the callee keeps seeing the "top-level" number,

Hi All, We've got msidn configured: Port 1: TE-mode BRI S/T interface line (for phone lines) -> Protocol: DSS1 (Euro ISDN) -> childcnt: 2 -------- mISDN_close: fid(3) isize(131072) inbuf(0x8fd5060) irp(0x8fd5060) iend(0x8fd5060) and running on Asterisk 1.4.21.2: pbx*CLI> misdn show stacks BEGIN STACK_LIST: * Port 1 Type TE Prot. PMP L2Link UP L1Link:UP Blocked:0 Debug:0

Hi I have beronet BN8S0 isdn card in my asterisk and , card is working fine, but when I try to dial to special number 118913 ( telephone number information) from polish telecom TPSA, I always geting timeout . Bellow is isdn signaling dump : --> * CallGrp: PickupGrp: --> rxgain:0 txgain:0 --> * dad:118913 tech:mISDN/2-u25 ctx:default --> * Setting Context to from-tpnet -->

Just to add.... P[ 1] Transmitting 128 samples 2 misdn P[ 1] writing 128 bytes 2 asterisk P[ 1] Sending :160 bytes 2 MISDN P[ 0] misdn_jb_fill: written:160 | Buffer status:256 p:861fee0 P[ 0] misdn_jb_empty: read:128 | Buffer status:128 p:861fee0 P[ 1] Transmitting 128 samples 2 misdn P[ 1] writing 128 bytes 2 asterisk P[ 1] PH_CONTROL: channel:1 oad2:07nnnnnnnnn dad0:820055 P[ 1] --> DTMF

Hi helpers, I seem to have a problem of intermittent DTMF tones being played during a conversation. Eg: Extn 100 takes an inbound call and all is fine. Except, at an undetermined time the person on extn 100 will here a DTMF tone for no apparent reason (it's not the caller pressing buttons). The caller doesn't hear the tone - only the called person. The call itself progresses normally.

Greetings everyone, I'm trying to compile asterisk for an AVR32 (Atmel NGW100). Buildroot for AVR32 already has the asterisk package, though it has bugs. Firstly it tries to apply a patch for 1.2 on a 1.6, but deleting the contents of the patch file did the trick. Now, the problem is making asterisk. The first error is because asterisk needed to be ./configure:ed. Trying to just do

I'd like to make some polar plots with R, but I can't seem to find anything designed to help with that. Is there anyway to get a real polar mode, where instead of x and y you have r and theta? How about a way to draw a circle? -.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.-.- r-help mailing list -- Read http://www.ci.tuwien.ac.at/~hornik/R/R-FAQ.html Send