similar to: Commands needed via AMI to find callerid of inbound call to extension

I have a number of inbound analog lines connecting through Digium cards to an Asterisk box. Asterisk then bridges the calls over to the internal extensions which are all SIP phones. Currenly the inbound lines do not have callerid on them so callerid=no in my zapata.conf file. What happens on inbound calls is that the SIP extensions are dialed but their callerid shows

On Mon, Jun 26, 2023 at 4:04 PM TTT <lists at telium.io> wrote: > It looks like if I call Getvar and pass PJSIP_HEADERS() I can get the > entire SIP header for a channel. I also read (on stackoverflow) that the > PJSIP_HEADER function will only return the headers from the INVITE of the > *inbound* channel. > > > > If that’s correct, how would I get the headers from

It looks like if I call Getvar and pass PJSIP_HEADERS() I can get the entire SIP header for a channel. I also read (on stackoverflow) that the PJSIP_HEADER function will only return the headers from the INVITE of the inbound channel. If that’s correct, how would I get the headers from the outbound channel (second leg of the bridged call) INVITE ? Or will PJSIP_HEADERS() in fact return the

Hi, We encounter a problem with the variable CALLERID(dnid) We use E1 lines where we can make an inbound call or an outbound call on the same channel (not at the same time) If the CALLERID(dnid) is not used, than the CALLERID(dnid) will be the CALLERID(dnid) of the previous call For example: - First we get a inbound call on channel DAHDI/11-1 with CALLERID(dnid) = '655871460' We read

I think that’s getting me close. I’m trying to get (or recreate) the FROM and TO lines of the header, from a system running PJSIP. I think if I use CHANNEL to get local_uri and local_tag I can recreate a FROM line like: FROM=<URI>;tag=TAG And if I use CHANNEL to get remote_uri and remote_tag I can recreate a FROM line like: TO=<URI>;tag=TAG Would it be correct to assume

Dear all, I think this is common, or at least how it is supposed to be, but whening dialing over a ZAP channel, it's taking around 5~ seconds to ring on the over end, likewise inbound. This is just with a normal Dial command. Are there any ways to tweak this? Thanks, Gavin.

We have several customers we need to place outbound calls for (in a single system). May have to place calls for thousands of different caller ids. Customer signs a contract guaranteeing the caller id they provide is owned by them. I have everything setup for AMI Originate and can place the calls. However, I'm encountering a problem with the caller id. The system I'm dialing through

We have an inbound PRI connected to our Cisco 3825 router which is then passing the calls to Asterisk as SIP calls. We're getting the CallerID number but not the CallerID name. We are seeing the name in the RPID field with a SIP trace on the Asterisk box but don't understand why it's not registering as the CallerID name. Here is a link to pastebin with the Sip trace. In it you

Hi, i've some trouble with an * installation when the following scenario happen. 1) Inbound call to SIP/xxxxxxxxxxxx ; 2) Call is redirected to ring group 6xx 3) SIP extension 1xx answer. 4) caller want to speak with john doe on his mobile 5) assistant put caller on hold 6) assistant start a call to john doe mobile using a php script (AMI - Originate with custom context to force outbound

Converting this customer from a MiTel system to asterisk. Discovered that the inbound calls from the T1 are going to extension 366. (This was mapped in the MiTel for some arcane purpose.) The dial plan I am currently using is shown below. When loading the dial plan, I get this warning: WARNING[5004]: pbx_config.c:1561 pbx_load_config: The use of '_.' for an extension is strongly

I currently have Asterisk deployed in my office with a TE411P. On the first port of this card is a T1 from the telco setup for D4 AMI. Unfortunately, I'm not receiving caller ID on inbound calls from this line. The caller ID information is arriving in the form *ANI*DNIS*. In zapata.conf, I have signalling set to em_w. The DNIS always arrives correctly, but I'm never receiving the ANI

Hi, I have configured the below things: Extensions Trunk Outbound route Inbound route IVR Ring group If anybody call to my DID number, my IVR is responded. After that, if he press 1, then Ring group will be activated. All are working fine. My Problem: I want to avoid IVR for some phone numbers depends on their called IDs. If my common users will call to my DID

XO fixed my caller ID name. I am using FreePBX and I can include a "wait" to my custom extensions. Is there a way to add a wait to the whole PRI? I assume that if I set immediate to yes, I can then have a "s" extension do the wait, but how would it get from the "s" to the DID extension? (also, I would rather not answer every call) Is there a "magic" spot

Hello, For each incoming or outgoing call, sip hardphones I'm using, turn BLF on and off like this: the first call (after leaving idle status) turns 1st BLF on, the second one turns 2nd BLF and so on, when a call is hanged, its BLF is turn off. My first question is : do you think such behaviour is general ? My 2nd question is : using AMI, how can I tell for a given extension : 1. the number

Hi, I have small confusion in my configuration which is I had some DID's like 044578900-04457999. I was configured dial plan below mention. exten => _0XXXXXXXXX,1,NoOp(Int exten:${CALLERID(num)}) exten => _0XXXXXXXXX,2,Set(outgoing_ident=0445789${CALLERID(num):-2}) exten => _0XXXXXXXXX,3,NoOp(Ext ident:${outgoing_ident}) exten =>

I would like to develop a Call Center Dialer (outbound and inbound calls) and it would use AMI method to communicate with Asterisk Server. A daemon would need to run in the background, would you recommend coding in PHP or Node.js? which would be much faster and stable. Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL:

On Mon, Jun 26, 2023 at 10:57 AM TTT <lists at telium.io> wrote: > I am connecting to the ARI with subscribe all, so I can see channels being > created. I now want to extract a variety of header variables (at the > moment the from and to tag). I tried to read them from the ARI but > Asterisk refuses since the channel is not in a stasis app. > > > > Is there a way

I've got a rather strange callerid problem and don't know how to debug it. I've got two X100P cards installed in a RH9 box and both are connected to individual pstn pots lines. Both are equipped with callerid and both display callerid info on regular analog phones (verified 100%). Incoming and outgoing calls are handled just fine. When an incoming call arrives on one X100P card, *

Sending this to asterisk-users, in case anyone has AsteriskNOW experience they can share. Joe ---------- Forwarded message ---------- From: Joe Wood <schmoe at gmail.com> Date: Wed, Aug 18, 2010 at 9:22 AM Subject: AsteriskNow REGISTER'ing s@ extension for all inbound trunks To: asterisknow at lists.digium.com Hello. Can someone tell me why AsteriskNow is reverting to registering