similar to: Sangnoma + Digium Bridging

Only 100? We had a single server over 300. From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users-bounces at lists.digium.com] On Behalf Of Zeeshan Zakaria Sent: Saturday, October 30, 2010 9:49 PM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] Under heavy attack My count has reached 100 for the day. The server serves doesn't serve

I'm trying to use a couple of old Western Electric type 500 phones (desk model, rotary dial). These phones work fine, as tested with telco lines (they dial, receiver/transmitter works fine, etc). I'm running Asterisk 1.6.2.11. I can't get them to dial through Asterisk. They are connected to a Rhino channel bank which is connected to Asterisk via a Sangnoma card (T1 with echo

I've been replacing an old Toshiba DK switch with an Asterisk solution. I'm needing a solution for fax machines that works as well as a POTS line from my carrier. If the POTS line is the solution, I'll keep it, but I'd rather move away from that. Here's what I'm thinking...will it work? I would use a dual-port Digium T1 card. In one port, I'd terminate a telco PRI

Hello All: Using the below dataset how can I make a barplot with Date(X) and NumEggs(Y) by Site. Then plot Temp(lineplot) It seems really simple, but I am having a hard time trying to do it by Site. Thanks Date NumEggs Site Temp 1 2008-04-22 0 Massacre Flat (RK424.5) 51.20 2 2008-04-23 0 Massacre Flat (RK424.5) 50.80 3 2008-04-24

We need to monitorate the E1 with nagios, somebody did this? any ideia? Thanks in advance! -- Atenciosamente, ------------------------------------------------------- Dario Quiroz (71) 9275-9080 gtalk: darioquiroz at gmail.com ------------------------------------------------------- -------------- next part -------------- An HTML attachment was

pbx18*CLI> module load codec_g729-ast14-gcc4-glibc-pentium3.so Unable to load module codec_g729-ast14-gcc4-glibc-pentium3.so Command 'module load codec_g729-ast14-gcc4-glibc-pentium3.so ' failed. [Dec 22 15:52:45] WARNING[4491]: loader.c:757 inspect_module: Module 'codec_g729-ast14-gcc4-glibc-pentium3.so' does not provide a license key. [Dec 22 15:52:45] WARNING[4491]:

I'm posting here in case anyone else runs into this and needs some help. I'll probably update the voip-info Wiki pages on Toshiba integration in a bit. Asterisk 1.6 makes things a bit easier than what is on that page. I'm integrating an Asterisk server with a Toshiba Strata system at my office. Right now, it is driving some VoIP phones (Cisco ATAs with analog phones plugged into

Hello I purchased an AEX800 card to replace the ageing cheap channel bank/T1 card solution a few months ago, assuming that it would be a more robust solution for my small scale phone system. However, it appears to be anything but that. Originally implemented as a XEN dom-u virtual machine on a large server class machine, using PCI passthrough to pass the AEX800 and a small older TDM400, then

I have a AEX800 PCI Express card - sort of a TDM800 with PCI-Express. (or AEX844 - 4FXS & 4FXO) I downloaded Asterisk Now - and have got this loaded on a new motherboard (Intel with 3 PCI, 3 PCI Express - etc). (Downside on PCI-Express is the physical support the express slot gives (very little) compared with an 'old' standard PCI slot!!!) With only this card in the box....

Hi All, I have installed asterisk 1.6.2.8 Dahdi: 2.4.0 Digium card: Digium, Inc. Wildcard AEX800 8-port analog card I have configured this card properly and it is working for calls too, But there is issue of one way audio on this outbound routes only, My voice is going to outside pstn number but i am not able to get their audio, I have disabled firewall, selinux is also off. If I am applying

I am running Asterisk 1.16.2.13, dahdi 2.4.0 and libpri 1.4.11.4 on an HP ML110 G6 using Ubuntu Linux 10.04 LTS. I have two Digium TE121 single T1 port cards and a Digium AEX800 8-port FXS card. All PCI Express cards. Co-workers are hearing hissing sounds on some calls, and I am getting IRQ errors when running "dahdi show status". I see that sharing IRQs for Digium cards isn't

Hi dears, I am from saudi arabia and using asterisk 1.6.2.13,Dahdi-2.3.0 and Digium, Inc. Wildcard AEX800 8-port analog card (PCI-Express) . I am facing problem with detecting caller id before first ring.I recorded the dahdi channel using dahdi_monitor command. Where I am able to see and hear caller-id dtmf tones. Pl tell me the procedure to upload recorded file if you needed. Something I want

i have this card installed Digium, Inc. Wildcard AEX800 8-port analog card (PCI-Express) following the steps below found on freepbx site cd /usr/src/dahdi-linux-complete-2.2.0.2+2.2.0 make make install make config /sbin/ztcfg echo "/sbin/ztcfg" >> /etc/rc.d/rc.local cd /usr/src/libpri-1.4.10.2 make clean make make install when i run make config i do not get

Has anyone used this board as an Asterisk server? http://www.supermicro.com/products/motherboard/ATOM/ICH9/X7SPE.cfm?typ=H&IPMI=Y I'm mostly interested about the possible compatibility issues this board may have with the AEX800 card.

Running Asterisk 1.6.2.9, DAHDI 2.3.0.1, CentOS 5.5 (update to date as of a week ago), I've installed a Digium AEX800P with 2 X400M FXO Modules and 1 VPMADT032 Module, hooked up to 5 analog lines. I get the error message referenced in the subject in my dmesg output everytime I load / reload DAHDI using the command "system dahdi start/restart". When I make an outbound call over

Just noticed this today: Digium TE220B Dual Span T1/E1 PCI Express Card with Octasic DSP-based Echo Cancellation Module<http://www.voipsupply.com/product_info.php?products_id=3352> It's about time Digium got on the ball and made PCI-e cards. What are people's experiences with this card? Anyone know if there are plans for a PCI-e analog card for FXO use? -------------- next part

Hello, in asterisk 1.4.30 all realtime configurations go well. In asterisk 1.6.2.11 the following appears on CLI : [Sep 8 16:43:43] WARNING[1843]: res_config_mysql.c:325 realtime_mysql: MySQL RealTime: Invalid database specified: MyDBase (check res_mysql.conf) [Sep 8 16:43:43] WARNING[1843]: res_config_mysql.c:325 realtime_mysql: MySQL RealTime: Invalid database specified: MyDBase (check

Hi - I had a client recently move their asterisk system (asterisk 1.4.26, dahdi 2.2.0.1, aex800 w/vpm module) to a "new" location, a building that's nearly 150 years old. I was not personally able to go there, but the person who did the move said the building's demarc room was "scary"-- water leaks, jumbled and frayed wiring, and all sorts of other fun. The echo on

Hi All, This is a request for testing for users of Asterisk 1.4 or 1.6 with any of the following Digium VoiceBus based cards: TDM2400P, AEX2400, AEX800, TDM800P, TDM410, TE120P, TE121, and/or TE122. From a practical standpoint, this branch should allow these boards to work in more systems / configurations where IRQ misses caused problems in the past. The updated wctdm24xxp and wcte12xp

We're in the process of replacing an ancient Centigram-based, but Fujitsu-labelled, voicemail system with an Asterisk solution. The system will interface with a Fujitsu F9600 switch and use the SMDI module in Asterisk 1.6.1.x to communicate the calling information needed to make the interplay between the two systems work smoothly. This portion of the project is configured and working fine, as