similar to: asterisk 1.8 Calendar

I have a E1 conected to asterisk all zap channels are ok, but when calls come into Asterisk caller don't hear none ring, the call goes straight into the menu, how can i simulate 2 or 3 rings? here it is my conf. exten => s,1,Answer exten => s,2,Wait,2 exten => s,3,NoOp(${CALLERID}) exten => s,4,ResponseTimeout,45 exten => s,5,DigitTimeout,3 exten =>

Someone have info about install an AVM fritz into FC3 ? I'm getting problems with kernelcapi, after succesfully installed the fcpci support. Thanks -- Adri? Vidal adriavidal@gmail.com Mail is better with 1Gmail

Someone can confirm the new release is out? Haven's seen any post about it!!!!! -- Adri? Vidal adriavidal@gmail.com

Somone in europe have had succes getting Callir ID showed on a phone screen conected to an Handytone 286 ? Adri? Vidal -------------- next part -------------- A non-text attachment was scrubbed... Name: not available Type: text/enriched Size: 235 bytes Desc: not available Url : http://lists.digium.com/pipermail/asterisk-users/attachments/20041124/e5514052/attachment.bin

Have someone running fine Alert-Info with a Snom 370 ( System Information: Phone Type: snom370-SIP MAC-Address: 0004132661BD IP-Address: 192.168.10.170 Firmware-Version: snom370-SIP 7.3.14 14961) i've tried exten => 200,1,SIPAddHeader(Alert-Info:<http://www.notused.com>\;info=alert-external) exten => 200,n,Dial(SIP/${EXTEN},30) Can see into the phone SIP trace is

Hi Everyone, I am running DD-WRT on a router that feeds about 30 Aastra 6753i. The phones occasionally go into "No Service" mode. The POE switch doesn't seem to be the problem as it's tested fine. I think the router sometimes gives up and comes back quickly. Or something of that nature. However, the connections are maintained if a call is going on because there are peer to peer

Hello! I'm having a bit of an issue with one of my installations that I cannot figure out. For some reason, when two people are in a call (both local to the * box, same subnet, pure SIP), the call will randomly be placed on hold and provide MOH to the other party. We're using Polycom IP430 handsets almost exclusively for this installation. Can anyone think of a reason why a call would

I'm getting "Got SIP response 406 "Not Acceptable" back from 10.0.1.2" occasionally when try to dial to SPA942 , anyone has any idea on this before i consider Firmware upgrade? -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20080326/2fd2c557/attachment.htm

Hi list, I have for a year I have an account to call with broadvoice from about 3 days beginning a not registered problem of, asterisk shows to a message of error with the DNS, and my dns this working fine WARNING[5770]: chan_sip.c:7595 transmit_register: Probably a DNS error for registration to 908XXXXXXX at sip.broadvoice.com@sip.broadvoice.com, trying REGISTER again (after 20 seconds) [Dec 16

My provider migrated from an old EOL softswitch to Trixbox. I have a number (8159093011) on a different server on a different network. It appears as though the incoming calls are trying to authenticate against that number, which isn't present on the box. Could someone help me decode this debugging output? I was calling 8159911010. My server is 208.100.1.33. Theirs is 208.1.87.235. I

I am trying to setup a simple pstn gateway using Asterisk and a X100p card. I have got everything installed using Redhat 9 and am able to load Asterisk. I also configured sip and I am able to connect to the asterisk gateway with Xlite on the windows side. I am able to dial 1000 and get the welcome message. What I am NOT able to do is dial a seven digit local or 10 digit long distance number and

I have asterisk 1.0.5 installed via apt on a debian system. It's a custom distrobution called Voyage Linux that runs from a flash card and I have a hard drive installed with mysql installed on it as well as apache. I have been though the AMP install guide (asterisk management portal) and in the interface it has a place for me to record new IVR menus. I have to dial *77 to begin recording

R people, I need to know if is possible to make data mining with R. If so, is there any manual or somewhere/one to consult about that. Thank you very much Adri?n

Hi, does the hint extension work together with the Snom phones in stable? I don't get an error in the dialplan, but it does not work either. On SIP/26 I want to monitor SIP/22. This is what I do right now: extension.conf [incoming] exten => 955,hint,SIP/22 exten => 955,1,Dial(SIP/22) sip.conf [26] ... subscribecontext=incoming ... Running Asterisk 1.0.2-BRIstuffed-0.2.0-RC2b TIA

Hi everyone, I have been long working on a project (http://asterisktools.org, to be released under GPL) that aims to provide desktop tools for Macs. I am finally getting to the release stages of this application and hope to have an early BETA available next weekend. If there is anybody who is interested in this tool, please send me an email as I am looking for people who can test the

R people, I'd like to know how can I make inequations with are, specially work with lineal programming. Thanks for your unvaluable help Adri?n

Hi, I tried to compile the latest version of postfix, runs fine on C6 and C7, on C8 it fails. Complaining about missing ypclnt.h, this should com from glibc-headers. Any suggestions? Adrian -- Adri P. van Bloois "Elegance is not a dispensable luxury but a factor that decides between success and failure." Edsger W. Dijkstra

Hello, I'm using dovecot 1.0 under debian etch. The lda socket path is set to: auth_socket_path = /var/spool/postfix/private/auth But this gives me the error: net_connect(/var/spool/postfix/private/auth) failed: Permission denied I suppose deliver is run as dovecot user. I read about running deliver as root with the suid bit set. I'm not quite sure if this is a good solution. Is there

Dear all, I'm looking for some material on data mining with R. I have something from Luis Torgo but I'd like to see something else. If anybody could help me I'll be thankful Adri??n

Hello everybody, I'm having trouble with samba 3.5.11 and an access 97 database. I work in a business with 5 users that use a mdb database over samba, and for the first to make a query everything works fine, but if some other user tries to make a query when the first one is doing it, the database works really slow, like if the .mdb file is being blocked (that's what I suppose). I've