similar to: BRI line issue on third call

Hi, Hi All, I've just delved into the world of asterisk and I'm having a few dtmf issues. Internally, amongst sip phones, dtmf is fine. Externally, if you ring from a GSM mobile, DTMF is fine, however if you ring from a standard phone, DTMF fails to register. I am attempting to use a quad port HFC-4S Beronet Card. I've been searching the web most of the last week and

Hi, Since a week ago I am trying to get chan_misdn working with asterisk 1.4.19, using HFC based ISDN card on Linux 2.6.22. My setup is done as detailed on wiki and FAQ. * mISDN and miSDNusers are 1.1.7.2, unpacked, build and installed. After installation and misdn-init, I have this: aragorn:root/pts/1: # misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lines) ->

Hi. I'm running Asterisk server with 10 sip phones, and 2 grouped T0 lines with 10 DDI numbers. My provider is France Telecom and my setup is : - Debian Lenny - Asterisk 1.4 - Linux kernel 2.6.25.17 - mISDN 1.1.8 driver - Sip phones Thomson ST2030 No problem with the SIP . But when reveiving a call on RNIS line (any of the DDI numbers), the associated SIP phone rings indicating _two_

i am using asterisk 1.6.2 with mISDN and a passive AVM Fritz!card on CentOS 5.5. The only thing, i want to do is a call-redirection from an isdn-call to my mobile via sip-account. My extension conf is: general] static=yes writeprotect=no [globals] OUT_PORT=1 [ISDN] exten => 12345,1,Dial(SIP/012346737222 at sipprovider.local) If i call to the msn 12345, the SIP-call is going out, but after

hi i've configured a Beronet BN8S0 Card with misdn beronet utility. the card is configured with all lines in TE and P2P mode, and it is connected with the special cable with an ISDN connection. i've turned on debugging to level 4, this is the output from the asterisk cli when i receive a call: P[ 5] MGMT: Short status dinfo 1000001 P[ 5] MGMT: SSTATUS: L1_ACTIVATED P[ 5] handle_frm:

I'm trying to set caller ids on outgoing calls. I have a quad BRI B410P card connected to my telephony provider. I know the list of DID numbers the provider assigned to my company. If I don't set the caller id then the callee always sees the same "top-level" number. If I set the caller id to a specific DID number we own, the callee keeps seeing the "top-level" number,

Use Set(CALLERID(num)=9999999999) instead of using CALLERID(all). Remember to set this BEFORE you Dial. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 12:36 -->> To: asterisk-users at lists.digium.com -->>

You're quite right. We'll need to see your misdn.conf file to check the settings. -->> -----Original Message----- -->> From: asterisk-users-bounces at lists.digium.com [mailto:asterisk-users- -->> bounces at lists.digium.com] On Behalf Of Vieri -->> Sent: 06 February 2009 13:49 -->> To: asterisk-users at lists.digium.com -->> Subject:

I'm running a setup with chan_misdn on a austrian PTP-line. When somebody dials in without an extension, he gets a busy signal. I don't see the call at all in asterisk. I *have* set immediate=yes in misdn.conf. And I *do* have an s-extension in my dialplan for the context used by misdn. Calls that provide an extension work fine. Attached is my misdn.conf and a verbose 3, misdn set debug

Hi all I have a very strange problem here... I use a hfc-s card with mISDN in NT mode with an ISDN Phone connected. When I make a call, the phone rings two or three times and then misdn runs into a timeout... I don't know where to set that timeout, but it's way to short for the called to pick up the phone. If the destination phone is picked up, then everything is allright and the

Hello everyone. I've got this really annoying HFC Cologne card (or however I should call it - a single channel ISDN card based on the HFC chipset). It wrongfully detects lots and lots and lots of incoming DTMFs, to the point the card is not usable. Here's a sample out of CLI: P[ 1] I IND :DTMF_TONE oad:206361 dad:520101 P[ 1] --> mode:TE cause:16 ocause:16 rad: cad: P[ 1] -->

Just to add.... P[ 1] Transmitting 128 samples 2 misdn P[ 1] writing 128 bytes 2 asterisk P[ 1] Sending :160 bytes 2 MISDN P[ 0] misdn_jb_fill: written:160 | Buffer status:256 p:861fee0 P[ 0] misdn_jb_empty: read:128 | Buffer status:128 p:861fee0 P[ 1] Transmitting 128 samples 2 misdn P[ 1] writing 128 bytes 2 asterisk P[ 1] PH_CONTROL: channel:1 oad2:07nnnnnnnnn dad0:820055 P[ 1] --> DTMF

Hi I try to connect my asterisk with a Siemens Hicom pbx. I have a PCI cologne Chip card wich support NT mode. I have compiled mISDN driver, and I use chn_misdn from debian package. The card wotk fine in TE mode but mot in NT mode. for informations : routeur*CLI> misdn show stacks BEGIN STACK_LIST: * Stack Addr: Uid 40200001 Port 1 Type NT Prot. PMP Link DOWN --> bchan: addr 0 channel

Hi I have beronet BN8S0 isdn card in my asterisk and , card is working fine, but when I try to dial to special number 118913 ( telephone number information) from polish telecom TPSA, I always geting timeout . Bellow is isdn signaling dump : --> * CallGrp: PickupGrp: --> rxgain:0 txgain:0 --> * dad:118913 tech:mISDN/2-u25 ctx:default --> * Setting Context to from-tpnet -->

Hi, I've run into a veird problem. I'm using a B400P BRI and an A1200P card with dahdi (2.2.1) driver. The dahdi_scan shows the each moduls and spans, everything seems fine. With dahdi_genconf I made the config, set up the channels in chan_dahdi.conf, but after reboot, the two card changes the order, (originaly the B400P is the first (closer to the processor) and A1200P is the

Hi, I have a B400P BRI card with point-to-point connection (signalling: bri_cpe) with this dmesg: http://pastebin.com/sXrRt1yM When i restart asterisk server, the card cannot connect to the telco, the control led flashes red. If I unplug the cable between the ISDN nt and the card and wait 40 sec, the card can connect and works properly. The telco says the asterisk crashes the connection

Hi, i use an BN4S0 with misdn an asterisk on Linux 2.6.9. The hfcmulti module is loaded with option: type=0x04 protocol=0x2,0x2,0x22,0x2 layermask=0xf,0xf,0xf,0xf and the fourth port is connected to an ISDN PTMP (MSN) port. Call to #72 from S0 (BN port 4) are not accepted from asterisk but why ? Can anyone give me a hint ?? misdn debug messages follows: lib: NEW_CR Ind with l3id:80001

I hadn't used FWD for quite a while. A customer sent me an email last week, "Is FWD broken when one tries to use it with IAX?" I have been playing around, and indeed seems to be the case. Is there anyone out there successfully using the two of them together? Thanks. B. -- This message has been scanned for viruses and dangerous content by MailScanner, and is believed to be

Hello everyone! I've just switched from Asterisk 1.6.0-beta9 to 1.6.0.1 and my mISDN is not working. Here's what happens, if I try to call the line: bach >> P[ 1] --> !! lib: No free channel! P[ 1] --> we have already send Release_complete I haven't changed the configuration fles. Should I change something there? If you need more info, just tell me and I'll

Hi. When I call my RNIS numbers (with a mobile phone for example), I can see 2 incoming calls on the IPBX, which should not happend. I'm not sure if it's a problem with the telco France Telecom and their ISDN setup, or if it's a problem with the MISDN driver on the IPBX itself. I'm stuck ... Any advices for troubleshooting that? Someone provide working configuration files