similar to: QoS and Asterisk

Using a Polycom 550 and 650 phones on my Asterisk server for testing. I can't figure out why the volume is so low. How can I adjust the volume control on Asterisk? It's at max on the handset phones. Thanks! Hin

Thanks to all the content from the archives and the HOWTO, I''ve got a QoS bridge running, based off the Dante script http://www.compsci.lyon.edu/mcritch/dante/ --> http://www.compsci.lyon.edu/mcritch/dante/shape.sh.eth0 While we are experiencing a marked improvement in Citrix consistency, I still feel there is room for improvement. Citrix sends a LOT of small packets. It is

Hi to all in a scenario where: - the bandwith is shared with other traffic (HTTP,VPN,ecc) - the PBX is on a remote VPN peer - due to many reasons Qos is not usable There is a IAX trunk between 2 Asterisk 1.4 i've tried different codecs (ulaw,alaw,gsm) but the main problem still remain the same: too many voice packet get lost. The main problem is surely on the network, but the strange thing

Hi all Asterisk Gurus. I am really badly in need of help. Asterisk is very lovely software, but has one big disadvantage.. lack of documentation.But let's get to the point. 1. Is it normal that I get such a crappy quality with iax, some drops and clicks? Could anyone with some similar setup check my quality and say if this is what the people are so excited about? ( I used to work as a speech

I''ll take it from the begining... About one year ago I only had 1 IP and used wondershaper. It worked great. Now I got /27 (32 IPs) and a gw computer that talks to two ISPs via a two tunnels. See: http://www.flashdance.cx/pics/flashdance-LAN.png I _really_ have a need to do QoS on my connection, for example I host websites that uses all available upstream. When I download at the same

If I relay through my Cisco 7940/7960, does it do QOS, even with a dumb switch? I know you can set quality/qos but only if you have a layer2/layer3 switch that supports the tagging. A simple little linksys 5 port switch wouldn't know about QOS, it'd give everybody equal priority. If a computer plugged into the phone, and the phone into the dumb 5 port switch and then to the internet,

Hi, I'm looking for opinions on the "best value" router to use for home offices. It should work for a scenario in which there are 3 computers and 2 SIP phones, handling QoS so that the phones always have higher priority traffic than the PCs. (and not rely on the phones to do the QoS because some PCs may not be connected to the phones). QoS could be based on destination and source

https://bugzilla.mindrot.org/show_bug.cgi?id=1997 Damien Miller <djm at mindrot.org> changed: What |Removed |Added ---------------------------------------------------------------------------- CC| |djm at mindrot.org --- Comment #1 from Damien Miller <djm at mindrot.org> --- The problem with this is that

Hi, I have what to me is an interesting issue. I am wanting to prioritize (QoS) traffic that will be passing through an IPSec (OpenS/WAN) VPN between two (identical) Linux routers. I know that I can apply the IPSec patches (1-4) to the kernel and IPTables (if they are not already applied by now) filter traffic before and after IPSec encapsulation. My problem is that I don''t know

I'm wondering if anyone knows of ISPs with service that has QoS features that would be good to use with VoIP stuff. Granted, the QoS would only be supported as long as you stayed within their network, but it might be better than nothing. --Eric

Greetings list, Thanks to all who replied to my thread a few days ago "SIP devices with packet loss tolerance". One of the suggestions that came out of that thread was to replace routers at users' premises with ones that support QoS. I've used m0n0wall's QoS in the past with reasonable success, but it's quite a bulky and complex setup for deploying to remote sites which

Guys. I need some advice on some h323 issues. I need to test connectivity from Asterisk to a Cisco AS5300 that has PSTN lines and to cisco 3600 voip routers. H323 needs to be used here but I was wondering if anybody has linked Asterisk to these Cisco routers before? Thank you for any pointers.

Hi I have Linux box (Debian) that acting as a bridge. Eth0 and Eth1 are bridged (br0). Br0 have public IP. Eth0 connects to the internet. Eth1 connect to servers in DMZ (with public IPs). Eth2 connects my Lan (192.168.1.0/24). My connections is 2Mbit/2Mbit. I''m doing SNAT for my Lan. QoS on eth0 works fine for DMZ, but is there a possibility to doing QoS on

Hello all, Can anyone recommend a good book which thoroughly explains QoS from a Linux perspective? Something with TC examples & the like. I''ve looked at the following: http://www.amazon.com/gp/product/1580533418/qid=1148368189/sr=1-2/ref=sr_1_2/102-2819973-6353768?s=books&v=glance&n=283155 Engineering Internet QoS. Thanks.

Hi! I have some problem in my asterisk 1.4.2, I've installed it on centOS 5.2 and this didn't accept voip QoS and can't route the packets having voip QoS. So I should change voip packets to be routing with centOS. I want to use iproute2 but i don't what to do after installing iproute2. Anyone could help me please? -------------- next part -------------- An HTML attachment was

I''m playing with the rather excellent QOS script from Alexander Clouter at http://digriz.org.uk/jdg-qos-script/ So far I am really impressed with it - a very impressive example of the power of linux QOS rules (has pretty much everything in it from the LARTC Howto!) However, the instructions hint that "for QoS to affect locally generated traffic in a non ethernet bridge setup

Hello All, I am interested in QoS provided by Linux, when I looked into IP header I came accross ToS field, also while going more into detail about QoS I found that the QoS based on ToS is serviced thru DiffServ which in turn gives more priority to packets with higher value is ToS field, but I am not able to understand when we finally call dev->hard_start_xmit routine of underlying device

I asked this on the list over the weekend, and likely missed a few people inboxes. I'm having a problem pulling data from RTPAUDIOQOS. For testing purposes I have asterisk sending QOS data to the console. It seems I get QOS data only if the caller hangs up, with the variable being empty if the callee (or asterisk) hangs up. Any idea why I would see this? exten =>

Hi. I did send this to `jaazz@post.cz'', but I suspect the list is a more appropriate/useful place for it. It''s a question about Michal Charvat''s QoS extension to Net-SNMP. When I look at the MIB entries for the QoS handles, I get something like this - enterprises.qos.qosObjectTable.qosObject.qosHandle.0.0 = Gauge32: 0

HI there Simple question :-) Why there is always only qos examples for upload and not download stream of adsl? I have a linux router which shares 5 wireless "customers" my neighbours and me to one adsl link 512kbps download 128kbps upload ... Now does it make sense to do qos on the linux router for download for us? Say if someone is using ssh from outside ... So I tried to apply the