similar to: 11.6.2 segfaults after dtmf on dahdi channel

Hi. When I dial a Dahdi extension using asterisk 1.6.0, and there is no answer, the extension hangs up, but the dial status is busy instead of no answer. How do I get this to work -- do I need to update dahdi? The card is an X400p using its FXS module. Thanks in advance for any ideas on this. -- Your life is like a penny. You're going to lose it. The question is: How do you spend it?

Under linux-2.6.38 I was able to compile and install dahdi, however when I ran dahdi_cfg -vv, I got an invalid argument on my fxs port. I have an old 400P card with one FXS and one FXO module. I have dahdi-trunk r9868 and dahdi-tools-trunk 8670. How can I get this to work correctly? Thanks in advance for any ideas. -- Your life is like a penny. You're going to lose it. The question

Hi. I am having problems with dahdi using kernel 2.6.32. I am using 2.6.30 kernel and it works fine -- here is the output of dahdi_cfg -vv ++ dahdi_cfg -vv DAHDI Tools Version - SVN-trunk-r8670 DAHDI Version: SVN-trunk-r7445M Echo Canceller(s): Configuration ====================== Channel map: Channel 01: FXO Kewlstart (Default) (Echo Canceler: mg2) (Slaves: 01) Channel 04: FXS Kewlstart

Hi. I have a Debian Leni system with asterisk-1.8. I was trying to get meetme to work and it depends on dahdi, so I compiled dahdi-trunk and dahdi-tools-trunk, however, when trying to insert dahdi_dummy, it complained about symbol crc_ccitt_table, although the module was actually there in the kernel tree. So, I took the Debian source, and I had the config and I did make Bzimage, make modules

Hi. I have run into a problem compiling dahdi-linux in kernel 6.1.0-10. Apparently there was a change, so I found a patch to fix stdbool.h but now I have an implicit declaration of pci_alloc_consistent in drivers/dahdi/wct4xxp/base.c I don't see any other references to that name anywhere. I am using version from git 5c840cf43838e0690873e73409491c392333b3b8 . So, the question, how to fix,

Hi. I am using gentoo kernel 2.6.27-r2 and dahdi trunk svn 5211 and it will not compile with this kernel whereas it does compile with 2.6.25. Here is the relevant portion of the build: VERIFY /usr/src/dahdi-trunk/drivers/dahdi/xpp/init_card_1_30 VERIFY /usr/src/dahdi-trunk/drivers/dahdi/xpp/init_card_2_30 VERIFY /usr/src/dahdi-trunk/drivers/dahdi/xpp/init_card_3_30 VERIFY

I am using viatalk as my voip provider and they use dtmf=rfc2833, but asterisk is not seeing any of the dtmf. I am using CVShead as of 8/26/05. Nothing in the logs indicates a dtmf is being seen. If I use my pots line it sees it fine. Any assistance would be appreciated. -- Your life is like a penny. You're going to lose it. The question is: How do you spend it? John Covici

Oh, I forgot to mention that Asterisk 15 went End-Of-Life last Thursday. :) You should use Asterisk 16. On Mon, Oct 7, 2019 at 5:58 AM George Joseph <gjoseph at digium.com> wrote: > > > On Fri, Oct 4, 2019 at 1:19 PM John Covici <covici at ccs.covici.com> wrote: > >> Hi. I am trying to install asterisk 15.7.4 from git onto a Debian 10 >> system and I am

Hi. I have a SIP provider which wants RFC2833 for the dtmfmode, however I would like to increase the duration of the tone, its pretty short and some IVR's are unhappy or don't detect it. I did poke around, but it looks like when RFC2833 is used, it actually generates rtp packets of some sort, so I have no idea how to increase that duration. Any assistance would be appreciated. -- Your

Hi. I want to use the new asterisk 1.4 with dahdi, but I would like to know the svn branches for the dahdi, so I can use them that way -- much easier to keep up with bug fixes, etc. Thanks. -- Your life is like a penny. You're going to lose it. The question is: How do you spend it? John Covici covici at ccs.covici.com

Thank you, very interesting! As I understand the Digium card is used as a interrupt source for Asterisk? Is there a diagnostic tool available ? Anybody else experienced a simmialr problem? Thank you! HB > From: > covici at ccs.covici.com > Date: > Sat, 12 Dec 2009 19:04:23 -0500 > To: > Asterisk Users Mailing List - Non-Commercial Discussion <asterisk-users at

Hi. I am having problems with asterisk detection dtmf properly in asterisk 11. I am up to rev 390229. Now, when coming in off a did we have with Velocity, the dids work fine, but from extensions often it misses digits -- I can type *4 and it will miss the 4. Often, if I type quite slowly things will work properly. All dtmf modes are set to rfc2833. Strangely enough, I did not notice this with

On Tue, Apr 26, 2016 at 11:07 AM, Administrator TOOTAI <admin at tootai.net> wrote: > Le 26/04/2016 17:23, Mamadou NGOM a ?crit : > >> Hello, >> >> >> Having installed DAHDI to be able to use the meetme() application , when >> I start the dahdi service it generates me the following error: >> >> -bash: /etc/init.d/dahdi: No such file or

Hi. I am using asterisk-1.8 and I am having problems getting conferencing to work properly. I did modprobe on dahdi and did load => chan_dahdi.so in /etc/asterisk/modules.conf. Now I do get conferencing, but meetme says [Jan 15 11:38:56] WARNING[9214] app_meetme.c: No DAHDI channel available for conference, conference recording disabled (is chan_dahdi loaded?) Now chan_dahdi is indeed

Hi. I have an asterisk system under Debian Leni using asterisk 1.8 with no Digium hardware -- and when I go into a meetme conference the system either locks up or is 100% cpu utilized or something -- I can't type anything and I have to physically reboot the system. The dahdi module is loaded and the last log entry is the playing of you are the only person in this conference,. How would I

OK, using zaptel 1.4 and asterisk 1.4 rev 6745, if someone types an asterisk from the other end of a call, I here it forever till the call hangs up. Looks like it starts the vldtmf, but never ends it from the logs. I am using Digium 400P rev I with one fxs and one fxo module. Any way around this one? Thanks. -- Your life is like a penny. You're going to lose it. The question is: How

Hi. I have a problem with my audio in meetme conference under asterisk 13 using Debian buster compiled from source. The problem is that there is some sort of distortion in the audio -- a workaround is always to lower the listen volume (*4). I see nothing in the log and so I wonder what is happening. I have dahdi loaded so I can record the conferences. Thanks in advance for any suggestions and

Rowland penny <rpenny at samba.org> wrote: > On 29/12/15 13:59, covici at ccs.covici.com wrote: > > Hi. I am having problems accessing subdirectories on a samba share. I > > am using windows 10 build 10586 and linux kernel 4.1.15-gentoo and samba > > 4.2.7. I have two shares, one called audio and the other called > > myshare. I cannot access the subdirectories

Rowland penny <rpenny at samba.org> wrote: > On 29/12/15 15:44, covici at ccs.covici.com wrote: > > Rowland penny <rpenny at samba.org> wrote: > > > >> On 29/12/15 13:59, covici at ccs.covici.com wrote: > >>> Hi. I am having problems accessing subdirectories on a samba share. I > >>> am using windows 10 build 10586 and linux kernel

The minute asterisk tries to execute an agi, it gets utils.c write error broken pipe and so hangs up the call. Anyone know what is going on? I am using kernel 2.6.27 with dahdi trunk if that makes a difference. thanks in advance for any ideas. -- Your life is like a penny. You're going to lose it. The question is: How do you spend it? John Covici covici at