similar to: PRI down due to chan_zap.c: No more room in scheduler....Got SABME and Sending Unnumbered Acknowledgement...Any thoughts?

Hi Guys, Anyone might know why this error keeps showing up and inbound/outbound is not working on a Bell PRI with Sangoma A101D? -- Got SABME from network peer. Sending Unnumbered Acknowledgement No calls can be made inbound/outbound. Keeps repeating. No alarms ON and no changes been made to the system. Stopped all a sudden. Asterisk CLI doesn't show anything with full verbose for both

Any ideas? Sangoma support is closed for the evening. I have the latest Sangoma drivers and Asterisk 1.4 everything installed. When I fire up asterisk, I keep getting "Primary D-Channel on span 1 up" repeated over and over. The B channels never come up. There are no errors in any of the logs, zttool, or the wanpipe tools. Intense pri debug output: < Unnumbered frame: < SAPI:

Hi, I'm trying to install an E1 PRI, and I need it working by Monday, but although everything seems ok, I get no response to calls. When I make a pri extense debug on span 1, I repeatedly get the following: Sending Set Asynchronous Balanced Mode Extended [ 00 01 7f ] Unnumbered frame: SAPI: 00 C/R: 0 EA: 0 TEI: 999 EA: 1 M3: 3

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hello List, since some days i run into the problem that one span on a TE407P is not comming up correctly. With intense debug on that span i get: < [ 02 01 7f ] < Unnumbered frame: < SAPI: 00 C/R: 1 EA: 0 < TEI: 000 EA: 1 < M3: 3 P/F: 1 M2: 3 11: 3 [ SABME (set asynchronous balanced mode extended) ] < 0 bytes of data

I've got a couple of PRIs coming in from a SUMA 4 switch with some 800 numbers routed through it. When the calls come in, I get the following message on the console and the call never makes it through: (800 number is fake) Extension '8005551212' in context 'nonauthenticated' from '232102749585' does not exist. Rejecting the call on span 4, channel 1. I do have the

Hi, I hope someone can help me with this.... Asterisk 1.0.6 Zaptel 1.0.6 Libpri 1.0.6, 1 Digium E100P card installed Panasonic TDA200 firmware v2.0.6 E1 Card Firmware 1.0.2 System is located in Australia, so as technologies go, I believe it is twist on the euro standard for the E1 signalling. Here is the situation. The TDA E1 card is set in cross over mode and I am using a functional

Hi, I have the following happen to me after the restart of one of my servers: out of my 3 PRIs (all configured with the same technical settings), the last one isn't coming back. It's underutilized (chances it didn't get a call since my reboot), if it makes a difference . The PRI goes from provisioned to unprovisioned, and I get this regularly: [Jun 22 09:03:48]

Hi everyone, I'm trying to get a Sangoma A101D-X card talking to a Sasktel PRI (Megalink) circuit and having some trouble getting it to handshake. Thanks for any help or suggestions to diagnose this problem. The problem is that Asterisk has trouble bringing up the link. I see the following lines every couple of minutes: == Primary D-Channel on span 1 up == Primary D-Channel on

Hello list, i've got some problems getting a E1 line with a E100P up and running (germany). # cat /proc/zaptel/1 Span 1: WCT1/0 "Digium Wildcard E100P E1/PRA Card 0" HDB3/CCS/CRC4 YELLOW RED "YELLOW RED" sounds not so good. When launching asterisk, enabling pri debug on that span, i see outgoing attempts: ;---------- snip -------- > [00 01 7f ] > Unnumbered

I managed to get Asterisk working with my PBX using T1, now I am moving on to trying to make PRI work. I have my zaptel.conf and zapata.conf configured as follows: Zaptel.conf: span=1,1,0,esf,b8zs bchan=1-23 dchan=24 loadzone=us defaultzone=us Zapata.conf: [channels] transfer=yes immediate=yes callprogress=yes language=en context=default switchtype=national signalling=pri_net group=1

Hi, I'm having problems with a new ISDN PRI in a new server. The cable is connected and the E1 modem seems to have issues with syncing (blinking light on the modem). versions: CentOS 6, asterisk 1.6.2.20, dahdi 2.5.0.1, libpri 1.4.12 ------------------------------------------------------------------------------------ dahdi show status T4XXP (PCI) Card 0 Span 1 RED 0

Hi All, I've a BT Versatility PBX that I want to connect to my asterisk 11.9.0 box via BRI port in NT mode but actually I wasn't able to get it working. I've another standalone PBX, it's a Panasonic model, which works fine connected to the same port. The BT connected to a UK BT BRI line works quite fine after roughly a minute once connected. The PBX can be seen at

Ok Guys, I've done a tonne of hunting around on this problem, but can't find much help. I'm running: asterisk 1.4.19.1 libpri 1.4.3 and zaptel 1.4.9.2 which I believe has been modified by RedFone to add the ztd-ethmf module. My interface is a RedFone foneBridge2 4 Span; and I'm connecting to a BT E1 PRI / ISDN30e with 15 lines on span 1, and a legacy Panasonic PBX on span 4. Upon

Hi I have a small ISDN PABX , (BRI) at home - Siemens Gigaset 4175 which has cordless DECT extensions. I have set up asterisk on FC3 with two HFC cards and I am using the latest bristuff. I am trying to use * between my ISDN line and my PABX. One card is in TE mode and can receive and make calls OK. I can make and receive external calls to a SIP phone. I cannot get the other card to talk to my

Hi. I'm running some asterisk boxes on different sites, some equipped with a couple of ZapHFC cards, others with Junghanns quadBRI cards. All boxes were compiled with Asterisk 1.2.10 (libpri 1.2.3 zaptel 1.2.6) and bristuff 0.3.0 pre 1s, distribution is Fedora Core 4 with kernel 2.6.17.3 The cards are connected to Telecom Italia's NT1/NT1+ S/T lines; some of them are point-to-point,

So we've got a TE410P configured as E-1. The PRI is showing up as normal, I have green lights, but d channel doesnt seem to come up and i keep getting this error if i do a "pri intense debug" The carrier swears up and down that there are no issues on their end. Any thoughts? localhost*CLI> > Unnumbered frame: > SAPI: 00 C/R: 0 EA: 0 > TEI: 000 EA: 1 > M3:

Hi I've been running into a weird issue, which its hard to get any information on. We successfully setup a R710 system with Asterisk 1.4.22 / libpri 1.4.7, utilizing a Digium TE121B Pci express card. However we are having some stability issues and can't seem to trace it down to if it is a card/system issue or our PRI vendor having a dirty line. I know some will say it is a old version of

Hi, I'm pulling my hair out, cause cannot connect to EuroISDN BRI in Italy with octobri card from Beronet. I use bristuff and have following zaptel.conf... # # This file is parsed by the Zaptel Configurator, ztcfg # # # First come the span definitions, in the format # span=<span num>,<timing>,<line build out (LBO)>,<framing>,<coding>[,yellow] # # The timing

Hello- I have a system with one D410P and one B200P (both OpenVox). All is well with the D410P, inbound and outbound, and I can initiate calls on the B200P BRI span, but there may be something wrong with my inbound BRI setup: there is no indication of an inbound call when I dial in to it from the PSTN. When I run "pri intense debug" and make a call to the BRI span, I can see a

Hi all, Last night I went to replace an Asterisk 1.4 + mISDN + b410p box with Asterisk 1.6.2 and DAHDI BRI - to no avail. I had two servers so copied network setting etc from the working one, moved the card across, ran dahdi_genconf etc and it didn't work. Here's the console output with notices disabled: lucas*CLI> pri intense debug span 1 Enabled debugging on span 1 [Dec 16