similar to: DAHDI not detecting hangup

Ok so this is officially driving me crazy. I have an Asterisk 1.6.1.6 install with DAHDI/DAHDI tools (latest) and an OpenVOX TDM400 card with 1 FXO port and 1 FXS port. I have a POTS line from my phone company attached to the POTS line. I have asked for "disconnect supervision" to be provisioned on my line and they claim to have added it. However, my scenario is as follows: I receive a

I've got a piece of CPE equipment that has an FXS port that I have tied to an FXO port on a TDM400 clone card. Normally, if I go off-hook with a standard telephone connected to it, I get a dialtone. If I dial a digit, and send a hookflash, the device will provide a dialtone back for the next available channel on the device. I'm trying to recreate this same behavior with Asterisk,

Hello, After installing on Ubuntu 10.04 using the tutorial on http://hmontoliu.blogspot.com/2010/03/installing-asterisk-and-freepbx-on.html I have a running instance of Asterisk. PROBLEM: result of dahdi_cfg: DAHDI Tools Version - 2.2.1 DAHDI Version: 2.2.1 Echo Canceller(s): MG2 Configuration ====================== Channel map: Channel 01: FXS Kewlstart (Default) (Echo Canceler: mg2)

I've spent a week playing with Asterisk 1.6 and I love it. What a brilliant piece of software! Progress and learning have been reasonably good. I have external SIP provider calls coming in and have put together a little call platform and I'm stunned at the flexibility. There is one issue for me. I took me a while to click that ZAPTEL now equals Dahdi, but now I'm there I have an

Hi guys, This has been bugging me for days and I can't figure out what's happening. Using the same channel on DAHDI, I can't make a call after previous one being hung up by remote side. However, it works like it should if my end hangs up the call. To make things interesting, DAHDI, or astribank rather, seems to "reset" itself after receiving an incoming call on that DAHDI

after installing asterisk 1.4.23.1 and dahdi-linux-2.1.0.4 and at CLI> module load chan_dahdi.so receive the following: signalling must be specified before any channels are. CLI> Warning [4663]: chan_dahdi.c:11627 process_dahdi: Ignoring signalling Error[4663]: chan_dahdi.c:10946 build_channels: Unable to reconfigure channel '1' Error[4663]:

Afternoon, I was hoping someone could point me in the right direction. I have an asterisk PBX deployed in China using a TDM400P based card. The incoming calls are being picked up correctly, but are not being hung up. I suspect that this might be an issue with the signaling that has been selected. If anyone here has deployed asterisk in china using an analog card, it would be a great help

I have an i686 cpu and when compiling from source I get this error: touch /usr/src/dahdi-linux-2.2.0/drivers/dahdi/xpp/init_fxo_modes.verified Building modules, stage 2. MODPOST WARNING: could not find /usr/src/dahdi-linux-2.2.0/drivers/dahdi/vpmadt032_loader/.vpmadt032_x86_32. o.cmd for /usr/src/dahdi-linux-2.2.0/drivers/dahdi/vpmadt032_loader/vpmadt032_x86_32.o Anyone else seeing this?

Hi, I am running Fedora 7 VM. On an earlier configuration with zaptel and Asterisk 1.4.21 , meetme worked alright. I upgraded to Dahdi and Asterisk 1.4.26, and the result is choppy sound via Meeme, while a simple Musiconhold works OK with descent audio quality. So I am sure its a Dahdi_dummy problem. Running dahdi_test gave me very poor results. Opened pseudo dahdi interface, measuring

When I do a service dahdi stop I get an error message: Unloading DAHDI hardware modules: execvp: No such file or directory the modules remain loaded. I dont know what to do with this??? Anyone else? I am running centos 4.4 2.6.9-42 This box ran 1.2 with zaptel fine. Jerry

Hello Friends, I am trying to Installl dahdi on amazon EC2 which have Open-SUSE-11.1 X86 version. and here is snap of uname- a command *Linux ip-10-160-86-41 2.6.32.19-0.3-ec2 #1 SMP 2010-09-17 20:28:21 +0200 x86_64 x86_64 x86_64 GNU/Linux* when I try to run DAHDI distribution dahdi-linux-2.1.0.4 I am getting following error *echo "You do not appear to have the sources for the

Hi, I need to run ztdummy for Paging, but now that this is all become dahdi I don`t really know where to start. I did build dahdi before building asterisk, but that`s it. I find it hard to find any documentation referring to dadhi instead of zaptel. I have no Digium hardware, but I still need the ztdummy timer (or whatever it`s called now). How do I get myself going? Regards,

Can anyone tell me what this message means? Got event 17 (Polarity Reversal)... I'm running DAHDI 2.0 with a TDM401 card. Asterisk version 1.6.0. It appears that I get this Polarity Reversal each time an inbound call hangs up. This results in another ring, but no one is there. It appears as an unknown caller, but I believe its a phantom. Thanks, Jim [Oct 10 12:47:54] NOTICE[6669]:

Hi, I am using asterisknow 1.5.0 and Wildcard TDM410P card. Everything is working fine except the caller ID of incoming call from PSTN line. The phone display is showing "Unknown" when there is an incoming call. I think the same problem listed here: https://issues.asterisk.org/view.php?id=6683 There is one patch on this link but i don't know how to apply patch on asterisknow.

CENTOS 5.5 dahdi 1.4.3.0.1 uname -r 2.6.18-194.3.1.el5PAE [root at localhost dahdi-linux-2.3.0.1]# service dahdi start Loading DAHDI hardware modules: FATAL: Module dahdi not found. wct4xxp: FATAL: Module wct4xxp not found. [FAILED] wctc4xxp: FATAL: Module wctc4xxp not found.

Hi all, I was using dahdi 1.6.2.0.9 version for a long time. We decided to upgrade to 1.6.2.22 a few days ago. After that we started to have some problems with dahdi channels. PS:DAHDI Version: 2.6.0 Echo Canceller: HWEC, MG2 We have 2 PRIs between Ericsson pbx and asterisk and a sip trunk for outside calls. At begining everything works fine but in a few hours, calls from asterisk to ericsson

We recently updated our Asterisk (1.4.24) box from Zaptel (1.4.12.1) to Dahdi (2.1.0.4). Everything seemed to go smooth with the exception of meetme. Meetme seems to not be able to find a zap channel for conferencing. We use voice introductions in our conference bridge and it seems to break that feature. The error from the console is.... # app_meetme.c:2593 find_conf: No Zap channel available for

Hello, # rpm -qa | grep kernel kernel-headers-2.6.18-274.18.1.el5 kernel-PAE-2.6.18-128.el5 kernel-devel-2.6.18-274.18.1.el5 kernel-PAE-devel-2.6.18-274.18.1.el5 [root at localhost ~]# uname -i i386 Trying to install dahdi-linux-complete-2.3.0.1+2.3.0 on CentOS but get below error. Can you please assist in this? [root at localhost dahdi-linux-complete-2.3.0.1+2.3.0]# make make -C linux all

Hi, I'm using a revision 6822-enabled Dahdi-Tools (see https://issues.asterisk.org/view.php?id=13897) with a Junghanns QuadBRI. 1. Do I still need qozap driver ? If positive, how is it recommended to get it ? 2. Which line should be included in /etc/dahdi/modules to have the appropriate driver loaded ? 3. The process I'm planning to use is : A- Hand edit /etc/dadhi/modules,

After a reboot, I can't reproduce the problem anymore which is quite frustating. 2011/6/14 Tzafrir Cohen <tzafrir.cohen at xorcom.com> > On Tue, Jun 14, 2011 at 03:44:32PM +0200, Olivier wrote: > > Hi, > > > > I'm using a two-years old installation script for the first time on a > > Squeeze (linux 2.6.32) platform. > > For an unknown reason (might