similar to: DAHDI Congestion cause 34

Hi, I have a X101P card and am running Asterisk SVN-trunk-r226890. The X101P card seems to be identified properly: debian:/usr/src/dahdi-tools# dahdi_hardware pci:0000:01:01.0 wcfxo+ e159:0001 Wildcard X101P debian:/usr/src/dahdi-tools# dahdi_cfg -vv DAHDI Tools Version - SVN-trunk-r7409 DAHDI Version: SVN-trunk-r7445 Echo Canceller(s): MG2 Configuration ======================

When I try and start asterisk I get the following, however I have commented out the data the connections in res_mysql.conf and res_pgsql.conf. I am not sure therefore why I am getting these errors. Do I have to change something else to turn this off? Thanks Asterisk 1.4.21.2~dfsg-3, Copyright (C) 1999 - 2008 Digium, Inc. and others. Created by Mark Spencer <markster at digium.com> Asterisk

I have a brand new IAXy I'm playing with. I do not get a dialtone on the phone, or any response at ll on the phone. No sound, no dialing, no ringing. The phone and wire are tested and known to be good. I think I have it setup correctly. When I give the iaxprov command I get this: #iaxyprov 192.168.1.90 iaxy.conf 02: c0 a8 01 5a 05: 11 d9 03: ff ff ff 00 04:

For anyone playing around with IAXy(S100i) devices, I am making the following available: Windows IAXy Provision v1.00 This is a from-the-ground-up development of a means of provisioning IAXy devices using a Windows environment. For some users, being bound to Linux for IAXy provisioning is not viable or convenient in some cases. This application provides a GUI data entry for the various IAXy

Hi, I've got an IAXy, and provided it with connection data - unfortunately didn't provide a fixed ip address, but left with dhcp. Everthing went fine, and I could work a while with it. After a restart of IAXy, it didn't negotiate a new IP address, nor used the old one. I even restarted the DHCP server and cleared its cache. No success. I went to another office with a different

Or: "An IAXy by any other name is still an IAXy" http://nextalarm.com/abn.jsp These folks are selling alarm supervision for us phone-line impaired folks. What's scary about this is that we probably need to install a fire/smoke detector with the IAXy ;-) IAXy users on this list -- who of you would trust their home/business security to an IAXy? Is there a silent majority who loves

Hi.. I have to setup an extension in a remote location that will use a cordless analog telephone.. I am looking at the IAXY to do this for me..Basically the data path will be as follows... [Asterisk] == (NAT) == {Internet} == (NAT) == ATA -- Handset Since there are two NAT boxes in the path I know SIP won't work.. I also don't want to move the Asterisk box to the internet side of the

I'm having a problem with my IAXy not always connecting to my Asterisk box. When I pick-up the phone plugged in to the IAXy I get a busy signal. I have to hang-up the phone and wait a few seconds after the orange LED goes out and then try again. When this happens I don't see any connection attempts in the Asterisk -r output. When I do get the IAXy to connect to Asterisk I get a

Hi all, I have a Soekris net4801-50 board with OpenBSD 3.9 where I've configured a dhcp server and tested it with a regular PC connected directly via a crossover cable with success. The problem comes when I try to connect my IAXy device instead of the PC. I can see with 'tcpdump -nettti sis1' that the IAXy isn't sending any packets to the dhcp server. I thought my IAXy was bad

Hey Everyone, I recently purchased a few IAXy units for some testing, and have come across a some problems. One of them can be provisioned but will not ring the connected telephone. It also does not provide a dial tone when you pick up the phone. When a call is made to the IAXy one of the green lights on the board goes from a solid on state, to a flashing state that coincides with the

Hi, hoping that experienced hands will quickly show me the right way: after a fruitless web search i am turning to this list with my rather elementary question: is there any other way to communicate with the IAXy besides using special utility software that needs to be compiled under UNIX? Here is the story: about two months ago, after some not very satisfactory attempts at using SIP (my phone

Ok, I searched the lists and found no definitive answer. I'm assuming the IAXy has some primitive form of echo cancel, is there anyway to adjust this? Or any ideas on what to do instead. Here's the setup, this will not be a typical setup for our company however, well whatever. Anyway it looks like this: IAXy --> Netgear router --> Charter --> Level3 --> Asterisk --> VOIP or

Yesterday I was using one of the cheap Radio Shack phone polarity on various phone outlets in my house and ended up plugging it into my IAXY. While the regular phone jacks tested OK, the IAXY tested as being reverse polarity. The tester was plugged directly into the IAXY so there is no chance of this being caused by crossed wires. Is this something that is misconfigured on the IAXY, a hardware

I've tried to simplified the dial plan and use "n" instead of numbers but I've noticed it is not executing my voicemail if I substitute number with "n" In the example below when the call is not answered, it does not go to voicemail; call just hangup. exten => 1,1,Playback(transfer) exten => 1,n,Dial(${sales_support}&IAX2/iaxy-322,20,jrw) exten =>

Hi, I have three Iaxy devices (s101i) parts. Two of them seem to work fine. The third plays a loud repeating click sound when an analog phone is plugged in. I can provision all of them, and make calls to all of them. The clicking one will blink when a call is incoming, but no audio from the call can be heard on the handset, and the caller only hears silence. The same handset works on the

We have many IAXy devices in the field now. In all cases, in iax.conf, we have "qualify=yes", so that using "iax2 show peers", we can see whether or not the device is currently online. In some cases, the IAXy device and/or Asterisk are not communicating their qualification, because "iax2 show peers" shows the device as status UNKNOWN. However, when a user picks up

In the mailing list archives, I found a message that indicates that the IAXy has the ulaw, alaw, and g726 codecs, but I cannot find anything official on Digium's site about it. The Installation Manual has an example iax.conf file that indicates the ulaw codec, so I know that one is good. But we are thinking about using the IAXy over a VPN, to replace our MultiVoip. alaw and ulaw are

When Asterisk first starts up, it will attempt to "bring up" the B channels on any PRI circuits. If you are using A@H then you can log on to the Asterisk CLI (asterisk -r) and then do "stop now" to stop asterisk. Start up Asterisk again by typing asterisk -cvvv at the Linux command line. You should see a bunch of messages on the terminal and then you'll get the Asterisk

According to http://kb.digium.com/entry/12/ The Iaxy will respond to pings on port 9999. You can ping your broadcast IP on your network and listen with tcpdump on your network on port 9999 which will show the Iaxy responding and what IP address it is coming from. Ex. ping 192.168.1.255 tcpdump -i eth0 udp port 9999" Before I get my karma whacked again, does this work for

I place a call from an IAXY to an IAXY device. INitially the calls show in the output of "show channels". Then after a few seconds the "show channels" command shows 0 active channels even though I am still talking on the channels. Any ideas on this? THanks, Jerry