similar to: is it possible to connect Digium TE420 and Cisco card?

Hi, I wonder if I may freely use the default soundfiles that came with asterisk (fpm-world-mix, fpm-calm-river and fpm-sunshine) on production server? Are there any official sources of royalty free music? -- Mvh, Aurimas Skirgaila -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi I'm having problems getting the TE420 working in HP DL380G5 servers. The cards don't seem to be detected 100% by the BIOS. With two cards in the server they are never detected. things I've tried: 1 Update firmware to latest (P56) for the server 2 change irq settings 3 disable all onboard devices on server and remove raid controller 4 different cards in different slots What I

Hello! Just got new server with TE420. Not all four spans will be used immediately, but spans not configured or not connected blink red light. Is it possible to turn span off, so my colleagues will not eventally tell me that something is wrong with asterisk? :-) Thank you!

Hi, long time ago, I came up with an optimal configuration set for my environment - good detection and little false positives. Unfortunately some people are always being detected as Answering Machines. I'm not up to re-adjust my precious balance of initial_silence/max_words/... , so I'm thinking about to check if the pickup time is equal to the pickup time when the same phone number was

hi, We have a phone number from third party provider which is used for inbound calls. How could I monitor if this *phone number* is reachable? the initial idea doesn't sound elegant: - on my SIP server I set couple seconds of ringing before Answer(). - the monitoring server calls to that phone number for few seconds, checks if it "hears" the ringing and hangs up the call. ** I use

Hello everyone. I have a timing slips errors and I can't understand what source of the problem is. My installation has 2 digium cards: TE420 and TE220 cards in one server. There are 3 spans (E1) to PSTN and 3 spans to internal PBS stations - normal installation for transit communication. Span configuration is: span=1,1,0,ccs,hdb3 #TE420 - first port. To PSTN. span=2,0,0,ccs,hdb3 #TE420 -

I have just built a new system using an HP DL360G7 with a TE420 T1 card, and this is the first system using a generation 7 server. I'm not sure whether that is an issue or not. I am using Asterisk 1.2, and Zaptel 1.4.12.1 with patches for GEN5 of the TE420 card. I have successfully used this combination on several systems based on the DL360G6 and TE420(gen5), which have been in production for

<rant level="mild"> I tried emailing support and got a rejection notice saying to go via the website, which then wants registered product details before it will let me enter a support request. Unfortunately, the card was bought by my customer, not by me :-( So I'll just have to ask here... </rant> I am currently trying to replicate an existing system build using new

Hi All I am getting a strange prblem while installing TE420 on a Dell Poweredge T100 machine. I get a "TE4XXX: version Synchronisation error " nad the machine hangs which needs a hard reboot . Its a new machine and if i install TE410P then installation is successful. Strangely enough i have a working TE420F on another Dell POweredge T100 machine at a different locaiton ... The DELL tech

I have the following software installed in a Centos Box with a TE420 (5th Gen) card. . Centos 6.5 64-bit . Asterisk 1.4.22 . dahdi-linux-complete-2.9.1.1+2.9.1 . libpri-1.4.14. Even without plugging in the ISDN into span 1, all 4 spans are flashing red. Plugging an E1 into span 1 makes no difference. My system.conf is just simply: loadzone=au defaultzone=au span=1,1,0,ccs,hdb3,crc4 bchan=1-15

Hello, I have an ISDN-30 connection and a Digium TE-121 with VPMADT032 echo cancellation. Every 30-60 minutes I experience PRI dropping. @@@ /etc/zaptel.conf: loadzone=dk defaultzone=dk span=2,1,0,ccs,hdb3,crc4 bchan=32-46 dchan=47 bchan=48-62 @@@ @@@ /etc/asterisk/zapata.conf [channels] switchtype=euroisdn usecallerid=yes group=2 signalling=pri_cpe context=incoming channel => 32-46

Asterisk 1.4.32 dahdi-2.3.0.1 Centos 5.5 Digium TE420 CAC channel bank (2) Cisco RVS4000 router Cox 50 Mbps/ 5 Mbps cable modem Flowroute provider codac G-711 90 % CPU idle callwaiting=no When there are 10-15 or more calls up the farend hears a callwaiting like beep every 3 to 6 sec. the duration of this "beep" is very short and would be no problem if it didn?t happen every few

Hi, I have IVR and when I press 1, asterisk calls my mobile phone. If my mobile phone is offline, asterisk transfers to asterisk voicemail. I'd like asterisk detects my mobile voicemail and if my mobile voicemail answers, asterisk transfers to asterisk voicemail. For that, I used AMD. So I have problems ! Asterisk detects answering machine everytime! How do I do please ? extensions.conf

Hi All I'm having some serious kernel panic while using digium cards. It may be related to IRQ shared. Can this cause a lot of drop call and bad voice quality ? Do you guys know if there is a way I can assign one IRQ for each digium card ? Thanks a lot. Here is the output of /var/log/syslog kernel: [ 3821.982893] Uhhuh. NMI received for unknown reason 20. kernel: [

So historically I've done one of two things on systems where I've needed to use MeetMe * used a real Digium card, and I've only ever used a TE400 or a TE420 for that purpose, and I know they have the timing chip * used dahdi_dummy, which works well with light load, but I had it running on a very overloaded server and had audio quality issues. I may have had quality issues even with a

Dear members of the list, I have difficulties to obtain sync with a Digium TE420 PCI Express For four entries E1, In my case I am with only 3 E1s available to configure. The telephony operator is BrasilTelecom and Signaling is R2 Digital. The information I have is that are E1s with 32 channels, not have sure. My settings Have been based on the link reference:

Hey, I wrote yesterday about PRI dropping, which turned out to just be a regular reset of unused B-channels. This time there's a real issue. As noted earlier I have an ISDN-30 connection, a Digium TE-121 with VPMADT032 echo cancellation. These are my configurations files: == /etc/zaptel.conf loadzone=dk defaultzone=dk span=1,1,0,css,hdb3,crc4 bchan=1-15 dchan=16 bchan=17-31 == ==

Hi, I'm having some questions related to echo cancellation configuration on a Digium board enabled systems (B410P, TE420, TE420B, ....) for cases when a hardware ech canceller is present or not. I read in TEXXX manual that when setting echocancel=yes in chan_dahdi.conf on a VPMOCT64-equiped system, 128ms hardware echo cancellation was enabled. 1. I'm correct thinking that it is then

Hello List, our setup: Callcenter IBM Hardware, 1x TE420, 1x xircom analog switch, 4x different cellular providers on the xircom analog port, ~60 agents Debian 5.0.1 (Lenny) Asterisk 1.4.21.2 Debian Package recompiled with additional app_queue segfault fix Zaptel 1.4.11 Debian Package My Problem is I have two channels (Zap/9-1 and Zap/6-1) which have a duration of over 4 hours. I am

Hi All, Is it possible to make a IAX2 connection between asterisk 1.6.1.0 , and asterisk 1.2.14 ? i tried to use a IAX2 connection between version 1.2.14 and 1.6.1.0 but it gave an error - 1.2.14 End - Error Msg WARNING[8313]: chan_iax2.c:7103 socket_read: Call rejected by 147.120.203.71: No authority found 1.2 END , IAX.conf [trunk14] type=friend host=147.120.203.71 secret=test123