similar to: ISDN Options

I had Asterisk 1.6.2.2 running fine with a mISDN using a HFC-S based card. I installed my TDM400P into the PC, it's really slow to boot now, when it finally does I gets stuck in a loop of reporting "isac xdu no tx_busy". Anyone able to assist? Thanks in advance! -------------- next part -------------- An HTML attachment was scrubbed... URL:

Hi, I have installed Asterisk 1.4 with mISDN with the install-asterisk.tar.gz script from beronet.com. On my system I have two cards, one a AVM Frit!Card Pci 2.0 and one HFC-S chip. I know both to work well with mISDN on my system from a previous installation. Now however, the AVM card works well at first glance, i.e. it "registers" incoming calls and works through the asterisk

Subsequent to some previous E-Mails, I've been trying to dig into the ISDN - BRI situation a bit more. I have determined that I have a HFC card with Winbond chip, but I'm not sure what combination of drivers is best or usable. zaphfc is out because it only supports the cologne chip. misdn is a possibility. I haven't determined if it supports the card natively, or needs a card

Mine is very similar: i don't have echocancelwhenbridged=yes because it seems work only on TDM, is it ? And in Italy, I often have set pridialplan = unknown About echo I have some problems, but only at the beginning of the call. After 3-4 seconds the echo became almost null, specially with snom 190; with pa168s and ywh10 I have again some problem, the echo come up also after 1 minute of

Hi, I would appreciate some advice on the following: how does one use a single BRI port HFC chipset based ISDN cards with the latest DAHDI, libpri and Asterisk 1.8? For Asterisk 1.4 I would first install mISDN & mISDNuser and then build Asterisk 1.4. Now I noticed that Digium's HFC chipset based B410P is supported by the latest DAHDI & libpri but reading the source of the

hello, anyone has worknig ISDN hfc-pci card in DDI (DID) point2point mode? what kernel ? and second question mISDN driver .. anyone has working solution with mISDN and maybe fritz card? what you suggest for DDI -> point2point mode (card,kernel,chan_..., ...) ? thank you, Tomaz

Hello, After searching the archives, I''ve found only two messages regarding this case, but there were no solution. I have a similar problem, so I try to ask here. I have twi HFC chipset ISDN cards in my pc: 0000:00:0d.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus

Hi, currently I got the following problem: The system contains a HFC-PCI card, it's running without problems under zaphfc. Now this system also should send/receive faxes. Receiving faxes works with rxfax (spandsp) but txfax is not comfortable enough and doesnt bring the demanded results. So an older external ISDN modem and mgetty-sendfax is used for sending faxes. I'd like to send the

Hi I have installed the http://asteriskathome.sourceforge.net/ with a Digium card with no problems, very good ! Now I want to install my Billion PCI ISDN card (HFC based) in TE mode. I get a little confused with Isdn4Linux, ZapHFC HIAX and the need to install Capi ! Please suggest best and easiest approach ? Thank you ! HB Norway

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

Hi! I just wanted to ask if anyone managed to get "ordinary" HFC-S ISDN cards with the zaphfc driver running in a Xen3 DomU. I am referring to this post ( http://lists.xensource.com/archives/html/xen-users/2007-04/msg00202.html ), which perfectly describes my problem and I am therefore going to simply copy-and-paste it here: ----------- snip ------------> Hi, I''m

Hello, I am trying to use a HFC-PCI (CCD/Billion/Asuscom 2BD0) card in TE mode to dial-in and out with ISDN. The problem is I can not get the card to dial out with a Zap channel. Dial-in is working. I am using bri-stuff 0.1.0-RC4 (but tried also RC3 and RC2k). I tried all combination of "immediate", "overlapdial", "pridialplan". I earlier also managed to dial out

Greetings to everyone! I am new to Asterisk and ISDN modules so i tried to follow many of the articles about capi, bristuff, mISDN and so on. Now I am working in mISDN but every way I try I have compiling errors! The HFC PCI card is a Digi Datafire Micro V. The bristuff give me the error "invalid module format zaphfc.ko" and I don't know how to compile and load it. The capi

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Hi! I'm struggeling had to get a hfc pci card working in NT-Mode. I've installed a very basic test system with just one hfc pci card connected to an ISDN-phone over a modified NTBA as described on jollies homepage. I commpiled asterisk as descibed in kape's INSTALL file that comes with 'bri_stuff'. I have not modified the config fieles yet. After connecting to asterisk by

hi list. after my unsuccessfull experiences with mISDN i tried again to implement a zaphfc based solution. problem is: sound on calls via capi is stuttering/broken and therefore unuseable. my conf: - cel 1300, 256mb ram - avm b1 via capi connected to my outgoing ISDN - acer surf pci via zaphafc and crosslink cable with termination as internal bus - siemens gigaset 3035 as internal phone -

Hi to all, I am searching to make work an Asterisk, with an ISDN card with Cologne Chipset. Here is the lspci: 01:09.0 Network controller: Cologne Chip Designs GmbH ISDN network controller [HFC-PCI] (rev 02) Subsystem: Cologne Chip Designs GmbH ISDN Board Flags: bus master, medium devsel, latency 16, IRQ 5 I/O ports at c400 [size=8] Memory at fdefd000 (32-bit,

Hi all, I'm fighting with a really strange problem that is really busting me. I have an asterisk 1.4.22 ( from a trixbox 2.6.2 ) and mISDN 1.1.7 3 extension on hardphone and 3 extension in softphone ( zoiper ) What happens is that sometimes the people on the other side of communication hear my voice as metallic and chopped. This happen either on incoming call than on outgoing call. If I

Hi, I'm setting up an asterisk server with this hardware configuration: AMD Athlon 1000 Mhz 256 MB ram 3ware ATA raid controller 2 * Ethernet controller 2 * ISDN HFC controller One ethernet controller is connected directly to the internet (public IP) One ethernet controller is connected to the internal lan One ISDN controller is connected to the public telephone network One ISDN controller

Hi, I'm very new to asterisk and managed to set one up in debian, I installed via apt-get the asterisk and asterisk-bristuff packages. I downloaded the bristuff source as well. I managed to get as far as loading the following modules: zaptel 199144 4 cwain,zaphfc,zttranscode,ztdummy But the problem now is that all channels that I try to configure gives me an error that