similar to: qsigchannelmapping parameter

Hello, I wrote earlier today about a new PRI installation in the Caribbean, where all outbound calls are functioning fine *except* calls to Sprint phone numbers, which get rejected immediately as "busy". The telco has been working with their switch manufacturer and took the output of "pri show span 1" from me and came back with this: ----quote--- Please check your timers

Hi Guys, Anyone might know why this error keeps showing up and inbound/outbound is not working on a Bell PRI with Sangoma A101D? -- Got SABME from network peer. Sending Unnumbered Acknowledgement No calls can be made inbound/outbound. Keeps repeating. No alarms ON and no changes been made to the system. Stopped all a sudden. Asterisk CLI doesn't show anything with full verbose for both

We have a server with a TE120 on a partial PRI trunk that several times a day declares the PRI trunk down and stops handling calls until the asterisk is stopped, the zaptel/te120 modules reloaded, and asterisk started. Just before things go down, the log shows the following error: ERROR[9424] chan_zap.c: Write to 28 failed: Unknown error 500 at which point a "show pri spans"

Hi everyone, I am reading through Sangoma Wiki right now. But someone may already and quickly notice this. I have a system that is down since the morning (maybe power intruptions). All seems fine except for "wanrouter status" shows disconnected. Following are the alarms raised. Should I call telco (they have long wait times) or should I just keep searching online for troubleshooting

Hi, In my lab, I'm testing BRI spans in NT/ptmp mode. My setup is: asterisk 11.2.1 libpri 1.4.14 dahdi 2.6.1 wctdm24xxp (HA8 hybrid with B400M) SIP phone <----> Asterisk with HA8 <----> Patton SN4638 <----> Asterisk <----> SIP phone The single BRI line I'm testing remains down: CLI> pri show spans PRI span 1/0: In Alarm, Up, Active I'm quite certain this

Hi Guys I'm configuring a TE212P card and have the following two entries in my /etc/asterisk/zapata.conf switchtype=dms100 signalling=pri_cpe When I reload asterisk I get the following messages: > -- Reloading module 'chan_zap.so' (Zapata Telephony) > == Parsing '/etc/asterisk/zapata.conf': Found > [Mar 30 17:48:42] WARNING[2985]: chan_zap.c:11072

Hi list! We currently have a PRI gateway composed by a box with two Digium quad-span PRI cards (a TE420 and a ). One of the cards is filled with TELCO1, while the other has first two slots filled with TELCO2, and 3rd slot with TELCO3. I am currently having (timer ?) issues on TELCO3 (span 7) D-Chan (202 as determined by dahdi_genconf ) is constantly failing causing on-going calls to terminate.

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I' try to implement an automatic callback mechanism, just for local SIP calls.. Callback on busy and on no answer. If the other party doen't answer, it should be possible to press 5 to place an callback. Here is my dial: exten => _X.,1,Set(EXITCONTEXT=callback) exten => _X.,n,Dial(${DIALNUM},${ARG2},dtT) And here the script for

Hi List, I have configured TE121PF card in E1 mode. I am using asterisk 1.6 and freepbx 2.7. My card staus turn in to green and looks like sync with the service provider. My service provider is BSNL - India. I have one toll free number for incoming and one land line number for out going calls. Problem : If i am calling to the toll free number, i am getting the ring but that call is

Hi, Is Asterisk "fully QSIG-compliant"? I currently have an Alcatel 4400 connected to Asterisk 1.2 and 1.4. Zaptel versions are 1.2.26 and 1.4.11. I am using switchtype=euroisdn and all works fine. However, it seems that Alcatel's latest firmware has dropped support for euroisdn which is really despicable. So now I need to see if I can migrate to QSIG which is supported by

Hi, we are still trying to properly connect a Tenovis PBX to an Asterisk server (asterisk 1.2.6, libpri 1.2.2, zaptel 1.2.5, Digium Wildcard TE110P), this time with QSIG. Calling from a Tenovis phone to a SIP phone (i.e. traditional phone -> Tenovis PBX -> QSIG -> Asterisk -> SIP phone) works with the following messages: --- Don't know what to do if second ROSE component is of

Hi all, My problem boils down to these errors: ... Unable to create channel of type 'ZAP' (cause 34 - Circuit/channel congestion) == Everyone is busy/congested at this time This is triggered by lines in extentions.conf such as: exten => _X.,1,Dial(ZAP/g1/${EXTEN},,W) The system is CentOS v5.2 with Asterisk 1.4.23 (druid-asterisk-1.4.23.1-2), a Sangoma A104

I have a server running Asterisk 1.4.14, Zaptel 1.4.6, Libpri-1.4.2 on a CentOS 5 server. The server has a single TE110 card connected to a provider called Alestra in Monterrey, Mexico. Since we installed everything we have been having problems dialing certain numbers, those numbers always fail when dialed from Asterisk but if you dial from your cell phone they always go through. I once has a

Hi I am trying to connect asterisk with a Cisco GW 2600 with E1 pri using a Digium, Inc. Wildcard TE210P dual-span T1/E1/J1 card 3.3V (rev 02), Errors: [Jan 28 17:32:33] VERBOSE[6182] logger.c: == Primary D-Channel on span 1 up [Jan 28 17:32:33] WARNING[6182] chan_dahdi.c: PRI Error on span 0: We think we're the CPE, but they think they're the CPE too. [Jan 28 17:32:34] NOTICE[6182]

I am looking to get the info about QSIG support in Asterisk. Does Asterisk have QSIG support? Does Asterisk support QSIG SIP Tunneling or QSIG SIP Interworking? If so, How to configure that? Thanks -------------- next part -------------- An HTML attachment was scrubbed... URL: http://lists.digium.com/pipermail/asterisk-users/attachments/20060503/3cb7f966/attachment.htm

That was my impression as well, I tried adding switchtype=qsig in zapata.conf, but all I see is the capi information... No connection... Janne > -----Ursprungligt meddelande----- > Fr?n: asterisk-users-bounces@lists.digium.com > [mailto:asterisk-users-bounces@lists.digium.com] F?r Peter Svensson > Skickat: den 23 februari 2005 21:34 > Till: Asterisk Users Mailing List -

I have a 'CONGESTION' Status with R2 protocol. While testing this scenario sip GW--?Asterisk ?Digium E1 R2 Protocol?Cisco E1 R2 protocol?sip Gw Find below my error and configuration ,where are the errors in my configuration ? ========================================================================= Connected to Asterisk SVN-branch-1.6.2-r235775 currently running on

I have a Toshiba PBX connected via a QSIG PRI to Asterisk. I can make calls from the Toshiba to Asterisk and internal calls from Asterisk to the Toshiba. What I can't do is make an call with an outside destination from Asterisk to the Toshiba. The Toshiba is looking for 9 to grab an outside line then it expects to see the 10 digits. In the FreePBX dial plan I use 9|. which sends 9 plus the 10

[Reposting, as was bounced for non-member, sorry if this is a dupe] Arrangement: { PSTN }--E1--[PBX]--E1--[*]--LAN--[SIP phones] \__[PBX system phones] Normal calls between PBX system phones and SIP phones work, in both directions. The call logs look like (ignore the no answer, it did ring):

Hello to all, I have a problem with an asterisk qsig. I have three machines: Nortel CS1000 --- Card Sangoma PRI ---> Asterisk QSIG ---SIP Trunk---> Asterisk I use Snom phones on Asterisk. If I call from Asterisk to Nortel, Nortel reminds me of the name of the person i'm calling and I visualize on the display of Snom phone, but if I call from Nortel to Asterisk, the QSIG does not send