similar to: AVM Fritz! mISDN with Kernel 2.6.32 - Any experiences?

Hi again! > I have excellent success with the tiny "fcpci" and chan_capi, which is > also working great with capi4hylafax. See > net-dialup/fcpci-0.1-r1 in gentoo (should not be difficult to use this > on other distros, but I have never done so). Do not confuse this with > the "fritzcapi"! I managed to install fcpci and it seems to run fine (capiinfo

Hi, I successfully installed 2 avm card in my asterisk box but I'm unable to make call. My capi.conf is: msn=0721111,07211115 incomingmsn=* controller=1,2 softdtmf=1 context=default echocancel=yes callgroup=1 devices=2,2 my capi info : Contr1: 2 B channels total, 2 B channels free. Contr2: 2 B channels total, 2 B channels free. my extensions.conf : exten =>

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Not strictly Asterisk related, but I'm trying to get an AVM Fritz! card to work with Asterisk on a Fedora Core 3 box. I've grabbed the official AVM Fritz CAPI driver from the AVM website and compiled against the current kernel. However, as soon as I modprobe it I get: CAPI Subsystem Rev 1.1.2.8 fcpci: module license 'Proprietary'

Someone have info about install an AVM fritz into FC3 ? I'm getting problems with kernelcapi, after succesfully installed the fcpci support. Thanks -- Adri? Vidal adriavidal@gmail.com Mail is better with 1Gmail

Hello everyone, I have been using an AVM Fritz! card with chan_capi and mISDN for quite a while in PTM mode and it was working finely. Now, I needed more DID/MSN, so I switched to PTP. But now nothing works anymore :( I am using Asterisk on Debian Sarge stable and installed Asterisk along with chan_capi from apt-get. I installed mISDN from the CVS of isdn4linux.de. It is : - Asterisk

Hi everyone, I have Asterisk SVN-trunk-r7498 running for a few months and I'm quite happy with it. However, I am experiencing a quality issue with my AVM Fritz!card PCI which is used with chan_capi. When somebody calls me on this line he hears a lot of noise and I hear "scratches" and "plops". It is very annoying. Below is is my /etc/asterisk/capi.conf I've tried to

Hi, I added a Fritz!PCI card to my asterisk system which is running on fc2 !. I installed the avm modules (fcpci) and when i try an capiinit and a capiinfo then everything seems to be OK (you can see capiinfo and lsmod at the end of the text) !. I installed the asterisk chan_capi module and when i start asterisk and enter the command capi info on the command line i get back: *CLI> capi info

Hi Everyone, Long time reader, first time poster. FINALLY got my First AVM Fritz Card up and running under Centos 3.4 Installed the second....modified the drivers etc as per the instructions found at the wiki System boots Modprobe capi all good modprobe fcpci all good modprobe f2pci the kernel then goes into Panic If Modprobe f2pci before fcpci the kernel still goes into panic.

HI all, Has anyone succesfully installed an AVM Fritz! card on Fedora 7 using the drivers at ATrpms recently? http://atrpms.net/dist/f7/fcpci/ I tried with a clean F7 build on my EPIA 5000 yesterday, after modifying /etc/capi.conf (removing the coment # in front of fcpci line) I received the following error when executing 'capiinit' - FATAL: Error inserting fcpci

I tried that but it still doesn't work... I think I don't have the correct approach. Have I to install any ISDN drivers (=modules ?) BEFORE dealing with CAPI ? If yes, why shouldn't I use the hisax drivers (which are kernel ones) instead of fcpci drivers (which doesn't seems to work, by the way...) And finally, how is it possible to link the two modules together? As you can see,

Hello everyone! Has anyone had success in configuring the "Fritz!Card DSL" card, a combination of an ISDN adapter and a DSL modem from the german AVM GmbH (http://www.avm.de/) in a dom0 Domain (Xen 2.0.7)? I had success in compiling the modules from http://www.avm.de/de/Download/index.php3 and they load fine with "modprobe fcdsl". But with the Xen dom0 Kernel they seem to

Hello all, I would like to know about the support for this ISDN passive card AVM Fritz-PCI v2.0 with Asterisk: 1. which drive should I use with Asterisk: isdn4linux or capi4linux from AVM (I read some messages on the asterisk-users archives but I didn't find the answer) 2. if the drive is isdn4linux then HiSAX support (for passive cards) is enough ? and the device /dev/ttyI0 (for

Hello there I have a serious issue with the AVM Fritz PCI V2 I have the following setup and the problem is, that the kernel freezes hard after about 16 hours. The second problem is, that the S-Bus gets jammed as well, so you can't even use a analog phone! on the NT Kernel 2.4.21rc2 with ACPI Patch and of course capi are there any reasons why this configuration should not work? And the

Hello there I have a serious issue with the AVM Fritz PCI V2 I have the following setup and the problem is, that the kernel freezes hard after about 16 hours. The second problem is, that the S-Bus gets jammed as well, so you can't even use a analog phone! on the NT Kernel 2.4.21rc2 with ACPI Patch and of course capi are there any reasons why this configuration should not work? And the

hello, does anybody know how to setup avm fritz pci card in p2p mode ? regards marian -- SUNTEQ s. r. o. Hviezdoslavova 9 # Prievidza # 971 04 # Slovak republic Tel: +421-46-5430 754 # Fax: +421-46-5439 144 http://www.sunteq.sk/ ------------------------------------------------------------ A mind is like a parachute... it only works when it's open.

Is case anyone wants to know... The Fritz! USB ISDN box works fine with Asterisk! I'm running CAPI 0.3.0 and love it, because the mini ITX server I have only takes one PCI slot which is now filled with a 4 port Digium card.

hello! I'd like to use my asterisk-box on a p2p-line from my alcatel pbx. isdn4linux and capi works fine on a s0-line from the pbx, but i need more then 8 msns, cause i'd like to implement a voice-mail system and an extension to our "old" pbx with voip-phones. had anyone success using isdn4linux on a t0 (p2p) line (of course with an inexpensive passive card like my avm

Hi, I have an AVM Fritz! ISDN card connected to an NT1 unit (Australian). I have no problems getting the drivers up and running but when using it with asterisk nothing happens. I call in using a mobile or analogue phone on either of the numbers and the NT1 activity light either flashes or goes solid while ringing but it pauses for a while and on a mobile i get call not answered and a busy

Hi All, I'm running the latest asterisk CVS code (from experimental), and hardware-wise an AVM Fritz!PCI Card, together with chan_capi 0.3.3. The problem is that any inbound/outbound calls result in echo on MY end (the asterisk end). I've played with the echo settings in capi.conf (mainly turning on echocancel and echosquelch, also tried playing with rxgain/txgain) to no avail. The only

Hello! Is there a way to use AVM Fritz!PCI as a ZAP interface and have it configured for ZAP channels? Thanx in advance! Roland Zagler mailto:r.zagler@fog.at @fog smart partners