similar to: PAP2

I have a Linksys PAP2. Identical setups for the two channels in both the unit and in Asterisk. In particular, both channels enable g729 and set it as the preferred codec, and have disallow=all and allow=g729 in sip.conf. If we make a call on one channel, it works (and uses g729), but if we make a call on the other channel when the first one is still connected, it fails. We have three g729

We have some extensions in our dialplan that start with a star. We can dial them from Zap phones and SIP phones, but not from phones connected to a PAP2. After the user presses star follwed by two digits (our extensions are dialed with star followed by three digits) he hears a fast-busy that comes from the PAP2, not from Asterisk. This also happens with the builtin *8 (call pickup). In

Hi, anyone can confirm if the Linksys's ATA and Router (PAP2-NA and RT31P2-NA) have the same limitation of just one G.729 call like the Cisco ATA 186 ? I'm testing both appliances here and found this issue but could not confirm this anywhere (nothing on the manual, no document or post from any user about this). In my tests they use G.729 only on the first call and G.711 on the

Is there a way to configure the linksys pap2 to automatically connect to asterisk on lifting the handset (presumably into the 's' state)? Asterisk would then be listening for DTMF tones to figure out what to do rather than having to put a dial plan into each pap2. I think the pap2 is pretty much the same inside as a few of the sipura boxes so the same thing might work if anyone knows...

I am using mysql sipfriends and can't seem to get the MWI to work. From what I've read it seems this is not supported with that dynamic system, and probably never will be. I was thinking of just setting a cron job or something to check every minute for voicemail and set our sip NOTIFY messages as needed. Also, the PAP2-NA has the ability to reboot via a sip notify and I would like to be

Hi, I have 3 PAP2 connected to *, they work fine but there are some things which I would like to improve, some of them are: - double ring tone when placing a call (I hear two tones it seems like the PAP2 is generating it's own tone) - some kind of noise (like glitches or something) when I pick up the phone (seems like some polarity thing) - I'd like to keep the tone after

I receieved my first PAP2-NA yesterday from our distributor(Tech Data). It installed pretty easily and has worked great so I went to order some more of these units today. When I logged into Tech Data this morning, the PAP2-NA was now marked as discontinued and no longer available and only the PAP2 version was available which is the Vonage branded version. :( I saw someone on the list say that

The best I can do so far (which appears to be a bit of a hack) is (<:0>S0), which says to add a '0' to the start of the string and dial immediately. This gives asterisk an extension dialled of '0', which isn't the 's' that i'd hoped for, but is a good start! (S0) by itself doesn't work, nor does (<:>S0). Any other suggestions? Thanks James >

I've got a PAP2 that I've got working with asterisk. At the moment, its configured so that when a phone is picked up on it, it connects to Asterisk. My hope is that I can let Asteirsk handle the entire dialplan, including dial tone generation. What would my context in extenstions.conf look like for this sort of dialing. More accurately, how can I get Asterisk to generate the dial tone on

Hi i am using pap2 phone adaptors as clients to connect to asterisk server i am able to make calls but i cannot access voice mail using phone or start recording while call is in progress and when i place a call to local sip extension there is a long pause ( 15 sec ) before the call gets dialled i assume that the problem would be due to the dial plan in PAP2 if so please help me changing it

Here is some info that may allow some "locked" PAP2 and PAP2-NA units to be used with Asterisk: I have a PAP2-NA (from a provider other than Vonage) for which I did not know the admin password, though the "user" pages were accessible to me. The provider had set it up to fetch at startup, its configuration file by HTTP from a numeric IP. It was running 2.0.10(LSc). A search

I am using my first PAP2 device from linksys. Used many polycom phones... I configured the PAP2 device with asterisk. I have the registration, thought I was good to go. Plugged in my Valcom 2924 public address analog connection, called the extension and I got busy... very strange I thought. I then looked at the status page of the PAP2 and it says the following Reg online and hook state OFF.

I've got a Linksys PAP2 on my Vonage account with unlimited usage, but my softphone-addon account only has 500 minutes. Anyone ever try to setup their * to mimick the Linksys PAP2 ? Any comments or suggestions on what problems I might run into if I try? -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm having a real problem with one of my linksys pap2. On outgoing calls the callee will ring, but caller (pap2) will not here it ring When the callee answers, no audio is transmitted either way. Asterisk reports the call connected and bridged correctly. Now the kicker is that sometimes it works and other times it doesn't. I have had the most luck calling land lines, but sometime

Hi all, I have a problem with the dialing tone in PAP2: When making a call, I can hear the calling tone 5 times and then it stops. The called party still hears the call but not the calling party. I've playing around with different parameters on the PAP2 web config with no success until now. Anyone has seen the same probelm? Thanks, Jose

I am having an odd problem with a linksys pap2 ata and asterisk... Asterisk won't detect digits from it until I issue a 'sip debug'. As soon as I turn on sip debugging, everything works perfectly (classic heisenbug)! Asterisk is latest Debian 'etch' packaged 1.2.13. sip.conf looks like: [mc_ext01] type=friend secret=ext01 context=mc_ata_in host=dynamic dtmfmode=rfc2833

In my seemingly endless search for the cause of echo on my SPA3000, I wired it up in the following configuration: Analogue Handset <--> (FXS)SPA3000(FXO) <--> PAP2 And set the Line1 dialplan on the SPA3k to '(<:@gw0>S0)' which means that as soon as I pick up the handset I get linked straight through to the PAP2, which gives me dialtone. Even in this configuration, with

We have a bunch of PAP2s, and using the # to send immediately does not work as described in the manual. The PAP still waits for the "Interdigit_Short_Timer" to expire before sending the dial string. In addition, the dialplan does not cause the string to be sent immediately as it should. Here's the dialplan I'm using:

I had just found a Dlink DVG-1120 on ebay and I'm curious if anyone has used you it with asterisk. They were only $65. I have tested with the Linksys Pap2 and found that box to be fairly nice except for a lot of backgound/white noise. I was wondering if any else had experienced that? Let me know if I've wasted $65 on the Dlink and also if you had similar experience with white noise on

I run a bunch of the Linksys ATA's.. I always use rfc2833 for DTMF. works very well and have never had a problem with it. ..o-------------------------------------------------------o. Brian Fertig NOC/Network Engineer Planet Telecom, Inc. Tampa, FL Office -----Original Message----- From: asterisk-users-bounces@lists.digium.com [mailto:asterisk-users-bounces@lists.digium.com] On Behalf Of