similar to: forward incomming line to modem

Hello, Is it possible, for testing, to connect an cat5 straight patch cord between 2 ports of a Digium B410P card and use these 2 ports as a normal dahdi trunk ? I've tried this: One port is set as NT, the other as TE. I would expect timing to come for system hardware so I choose in /etc/dahdi/system.conf : span=1,0,0,ccs,ami span=2,0,0,ccs,ami Results: - both ports lights are green -

Hi all, I am having trouble setting the signalling method for the B410P using DAHDI. Asterisk complains that it has never heard of 'bri_cpe' or 'bri_net' - but it doesn't mind having 'pri_cpe' etc. ERROR[4294]: chan_dahdi.c:11327 process_dahdi: Unknown signalling method 'bri_net' Dahdi - dahdi-linux-complete-2.1.0.4+2.1.0.2 Asterisk - 1.4.23.1 Libpri - 1.4.9

hello: thanks for Tzafrir Cohen for dahdi testing. I installed dahdi-2.1-r3c svn code and asterisk1-6 for testing OpenVox B400P and junghans card. i fund that there is bug (i think) to dectect NT or TE mode. actually on the board, i set it as TE mode, but after start wcb4xxp, but it show the port is NT mode. to detect the TE mode, I modefy the code in base.c

Hi, I'm experiencing difficulties to get a B410P running with Asterisk 10.3.1 and DAHDI 2.6.1. Am I supposed to use DAHDI for this card and ISDN BRI for my country (Belgium)? thx, BC

Hello everybody, I try to install -Ubuntu 8.04 server- a B410P and a TDM2400P together with Asterisk 1.4.26-2, dahdi-linux-2.2.0.2 and dahdi-tools-2.2.0. Problem I face is the following one: CLI> module load chan_dahdi.so == Registered application 'DAHDISendKeypadFacility' == Registered application 'ZapSendKeypadFacility' == Parsing

Hi list! I am installing an * box that will be installed on a site with KPN BRI ISDN in The Netherlands. I am using bristuff fron Junghanns. Does anybody know the correct settings for this? I will not have internet access there which makes it harder to google around on location. switchtype = euroisdn is pretty obvious but what about these settings: signalling = bri_cpe_ptmp ; p2p TE mode

Hi, When startin * it tells me: ================================ [chan_zap.so] => (Zapata Telephony w/PRI) == Parsing '/etc/asterisk/zapata.conf': Found Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf: Updated conferencing on 1, with 0 conference users -- Registered channel 1, PRI Signalling signalling Sep 3 17:21:59 DEBUG[1076873856]: chan_zap.c:1208 update_conf:

Hi, i've downloaded/compiled/installed the bristuffed asterisk Asterisk 1.0.7-BRIstuffed-0.2.0-RC8a and i'm using it with an hfc card. It runs on a debian 3.1 sarge machine with kernel 2.6.11. Asterisk works well if i configure the card using isdn4linux. I'm having problems dialing out (not tried the input yet). This is the output from asterisk: -- Accepting AUTHENTICATED call from

Hi! This weekend we had a problem with our Asterisk Box which ran flawlessly for nearly 4 weeks. The Asterisk server sits between the PSTN and a Siemens PBX and bridges 2 BRI lines. No calls, not incoming, not outgoing. The admin rebooted the Dell Box and then everything worked fine again. Now, I'm analyzing log files to find the cause. During the Asterisk outage the logfiles only show

I'm just getting started, and getting quite a strange result. I've been able to mount my (login hal) Linux home directory as E: on my w95 system, but when I try to "smbmount //isdn2/AMDAHL-WORK /mnt/amdahlwork", where /mnt/amdahlwork is an empty directory on Linux, isdn2 is defined in /etc/hosts as 192,168.1.2, the address the W95 box uses, and AMDAHL-WORK is the name under

I am running * with a Junghanns quadbri that should allow us to integrate our ISDN house telephone system with VOIP. Preferably I would like to run a setup, so that our internal ISDN phones on an S bus are not aware that * is sitting in between. With the configuration below I run into the following problems: 1. On outbound calls, I get the normal rining call progress tone althought the

Hi! Has anybody seen anything like this using zaphfc? On outgoing calls (via isdn) , the line gets hung-up as soon as the called party answers. As seen below i get some protocol error (6) - but i'm not sure if this is related to the "hang-up" which apparently comes a little earlier?! Incomming calls on the isdn (zaphfc) interface is working just fine (P.S. what about the

Hi sir, I was installed Goautodial server and I have b410p BRI card. BRI card showing OK with dahdi_tool, this NT mode. whenever I am dialing from server i am not able to connect the call . in Cli below mention warning is comming . please what is the mistake with me . help me Executing [0559566768 at default:1] AGI("Console/dsp", "agi:// 127.0.0.1:4577/call_log") in new

Hello all What I'm looking for is some plain speaking advice on ISDN. Currently using 4 analog lines connecting via a four port TDM400P FXO card. We need to physically move our installations, and on requesting the analog lines be moved - our telco (BT) is suggesting we replace our analog lines with ISDN2. We would have 3 x ISDN2 connections, giving us six voice channels. They've

Hi, I have done my best and tired of searching the net about the problem. If anybody could help would be a great favour. Description of Problem ------------------------ I am trying to install two Netpci cards(Traverse Technology Netjet ISDN-s) on Trixbox 2 and aim is to use in Asterisk as dailin and dialout. I compliled the driver as directed in the manufacture manual. After installation dmesg

The DAHDI docs actually include the 'steps' that used to be in Zaptel's 'make b410p'. These steps involve downloading and compiling mISDN. Why re-invent the wheel? Just a thought :-). As for the 100ohm termination bit - it's simply changing a couple of dip switches on the b410p card (as described in the manual). Andy -----Original Message----- From:

Hi, I'm having some trouble setting up a Xorcom Bri 4 port. I have compiled asterisk and zaptel using the Bristuff bristuff-0.3.0-PRE-1y-g patches. So I'm running zaptel-1.2.17.1 and asterisk-1.2.18. The problem I'm having is that for one I get no LEDs showing if the unit is in TE and NT mode (not a issue for me but may have some impact on things) I have no errors in any logs I

Hi, My set up is : Asterisk with B410P in NT mode <-------------cat5 straight cable ----------------> Another PBX in TE mode Is the 100 Ohm terminator you can find on B410P boards, necessary when connecting in NT mode to another PBX (set in TE mode) ? Cheers -------------- next part -------------- An HTML attachment was scrubbed... URL:

I'm getting a strange error on one of the two controllers on an AVM C2 card under chan_capi-cm-0.6.3. I have two ISDN controllers defined, both in the same group, both connections are UK ISDN2e Point to Point: On the third outbound call (both of the first two calls are handled by the second controller "ISDN2",) I get this error : chan_capi.c conf_error 0x2001 PLCI=0x301

Hi list, we have a dual Xeon server with 2GB RAM running Debian Etch 2.6.18.4-686 kernel. The server has 2 B410P cards plugged in. No other card. We installed Asterisk 1.4 trunk with zaptel trunk, ran make b410p, the install mISDN1.1.0 (for bug 9064) configure and compile Asterisk with chan_misdn, all is fine. In misdn-init.conf we have added option=1,master_clock. Asterisk is up and