similar to: conferencing without DAHDI

Hi! What are the typical ways to work around the 64 groups limit? thanks klaus

Hi! I've went through the READMEs and could not answer this question: During installation, the Setup program asks: Would you like update/upgrade wanpipe drivers? (y/n) For a pure Asterisk TDM installation - is it required to patch the kernel or is this only when using the sangoma cards as WAN router? regards klaus

Hi all, Is it possible to install more than 1 asterisk in a single server? If yes, what do I need to set and take care? Rgds, ango

I'm currently writing some code to support conferencing in Asterisk without using the Meetme application. The conference runs in its own thread and every new inbound or outbound channel that is created is passed to it. This thread runs the conference loop reading and writing frames to each channel. I'm writing this as if it were a bridge with more than two channels, and I'm not

Hi! I am looking for a tool (application or webinterface) which shows me the current status of an Asterisk server, e.g.: - Status of the SIP peers (registered/offline) - current incoming and outgoing calls - start-time, numbers, some history - history (calls stopped in the last 15 minutes, who hang up?) - should be possible to link those calls to the relevant SIP peers -

Hi! Is it somehow possible to evaluate the SIP response code inside the dialplan? I have an Asterisk server which forwards requests to various PSTN gateways with SIP. If the Dial() attempt is not successful I want to differ at least these 3 options: - called destination is busy (486): e.g. activate auto-redial - called destination does not exist, unassigned number (404) - gateway is broken,

Hi! I have the following problem with Asterisk 1.4.23: ATA w/ T.38 Asterisk ATA w/o T.38 --------INVITE--------> --------INVITE--------> <-------200OK---------- <-------200OK---------- --------ACK-----------> --------ACK-----------> --------INVITE

Hi! Since some time the download of the newest Asterisk does not contains the version number anymore, but is just called "asterisk-1.4-current.tar.gz" This gives me a tarball where I do not know the version without looking into the tarball. Thus, IMO it would be very useful to switch back to old schema war the download contained the version number. Thanks Klaus

Hi! All the AEL examples have a semicolon after the closing curly bracket, e.g: context test { 1 => Hangup(); }; but without ; it works fine too, e.g: context test { 1 => Hangup(); } So - what is the reason for the ; after the closing curly bracket? thanks klaus

Hi Asterisk Users, we are using Asterisk 1.4.18.1 on debian 4.0 etch, pwlib 1.10 and openh323 1.18. We are using MeetMe for conference calls and with two participants there is no echo problems, but with more than two participants there is a lot of echo that sometimes disappear for a short time and all function well. Someone have some suggestions?? Do you ever used app_conference

Hi! I have a setup with Asterisk in front of a PBX connected with ISDN to the PSTN and to the PBX. This Asterisk (a old 1.2 instance) is doing ENUM for outgoing calls and allows incoming calls per SIP. Recently the IP connectivity for this location was down the whole telephony was down too - not even incoming calls did work. This is really strange as incoming calls from PSTN are routed

Hi All; I am facing a problem that always the users confused and connect the telephone line coming from the telephone service provider to the FXS port and cause it to be damaged, specially if the card was 2 fxs and 2 fxo, so they make mistake and connect the line to fxs while it should be connected to fxo. What is the solution for this disaster? Regards Bilal

Hi! I wonder why users.conf generates a SIP user and a SIP peer? Why is it not possible to set type=... in users.conf? (Asterisk 1.4.22) thanks klaus

Hi all, I've been trying to get meetme working for a while now (complie problems - will probably try again later on another machine) but have given up and started looking at alternatives. I've managed to get app_conference compiled and installed - show modules shows its there in asterisk, but I don't know how too actually use it in the dial plan... The info on voip-info

I have used every asterisk 11.8.X version. Have not had an issue till 11.8.0 and 11.8.1 When I use ConfBridge I am attempting to put all participants in MUTE mode and just one talker... However, since 11.8.0 I am hearing feedback in the announcement like the channel is not really muted. I dropped back to 11.7.0 and I hear no feedback. Has something changed - or - am I not correctly setting up

Hi everyone. I am looking at providing a conference for up to 300 people and was wondering if anyone has scaled meetme to 300 people. Here are some points: 1) I am using an IAX2 gateway hosted on a VOIP service provider. 2) The machine is hosted at the providers site so one has to assume that bandwidth is not going to be an issue. 3) Everything is coming in as ULAW so we won't need to

Do anybody could compile app_conference on x86_64??? I tryied with two versions of app_conference and got the same problem on compiling: relocation R_X86_64_32 against `a local symbol' can not be used when making a shared recompile with -fPIC app_conference.o: could not read symbols: Bad value" ENVIRONMENT:

Hello Asteriskos, Screenshot: http://www.areski.net/asterisk-meetme/about.php The goals of this application is to control your audience/users in the conference room. That will allow you to have a visual presentation and to control the conferences over the net. A lot of changes has be made to app_meetme to keep some conferences informations into a DB and to check through if some properties has

Hi all, <p>once again i came up with my conferencing stuff. On a conference with more then two people it's a waste of bandwidth, that every entity send it's data to every entity. Since there is only one audio line, the audio must be merged on the server. Here are my questions: - How many audio chanels can a server process (let's say a 3GHz machine) in this way: decode all

As stated here: http://www.voip-info.org/wiki/index.php?page=Asterisk+cmd+MeetMe A Meetme room uses Ulaw as the audio codec, so if the other channels use different codecs, then * will transcode. Does the app_conference application works the same way? Or if i have SIP/g729 users and i create a conference with other users also at g729 asterisk will not transcode (when using app_conference)?